Festo SPAN Handleiding

Bekijk gratis de handleiding van Festo SPAN (6 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 29 mensen en kreeg gemiddeld 4.5 sterren uit 9 reviews. Heb je een vraag over Festo SPAN of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Pressure sensor SPAN

Festo SE & Co. KG

Ruiter Straße 82

73734 Esslingen

Germany

+49 711 347-0

www.festo.com

Operating instructions8035566

2017-11a

[8035568]

Translation of the original instructions

Pressure sensor SPANEnglish..........................................

For all available product documentation è www.festo.com/pk

1Product description

The operating instructions describe the entire function range. The function range is

limited, depending on the product variant.

Note

You can find detailed specifications for the product, the device description file

(IODD) with a description of the IO-Link parameters and the declaration of con

formity at: è www.festo.com/sp.

1.1Overview

1

2

3

456

1Display

2Electrical connection

3Pneumatic connection

4B-key

5Edit button

6A-key

Fig. 1 Representation of other variants can deviate from this

1.2Characteristics

CharacteristicValueDescription

TypeSPANPressure sensor

Pressure

measuring range

-B2, -B11, -P025, -P05, -P1, -P2,

-P6, -P10, -P12, -P16, -V025,

-V05, -V1

è Technical data

Supply portRRelative pressure

Pneumatic port-G18, -R18, N18, -M5,

-Q4,

Thread Gx, Rx, NPTx, M5

Push-in connector4 mm

Thread type

M

F

None

Male thread

Female thread

Electrical

output 1

-PNLK

-PN

Switching output PNP / NPN / IO-Link

PNP / NPN

Electrical

output 2

-PNVBA

-PN

PNP / NPN / 0…10 V / 1…5 V / 4…20 mA

PNP / NPN

Electrical

connection

-L1Plug connector, design L1

Certificate

+T

Without

With inspection report

Fig. 2

2Safety

Intended use

The pressure sensor SPAN is intended for monitoring pressure of compressed air

and inert gases in the piping.

General safety information

Only use the product in its original status, without any unauthorised modifications.

Only use the product if it is in an excellent technical status.

The product is intended for use in industrial environments. Measures may need

to be implemented in residential areas for radio interference suppression.

Take into consideration the ambient conditions at the location of use.

Operate the product only with compressed air of the specified air quality class

(è Technical data).

Observe the specifications on the rating plate.

Comply with all applicable national and international regulations.

Disposal

Observe the local specifications for environmentally friendly disposal.

Range of applications and certifications

In connection with the UL marking on the product, the information of this section is

also applicable for compliance with the certification conditions of Underwriters

Laboratories Inc. (UL) for the U.S.A. and Canada.

UL approval information

Product category codeQUYX (USA)

QUYX7 (Canada)

File numberE322346

Considered standardsUL 610101

C22.2 No. 610101

UL mark

Fig. 3

Unit shall be supplied by a power source which complies with the requirements of

a limited-energy circuit in accordance with IEC/EN/UL/CSA 61010-1 or a Limited

Power Source (LPS) in accordance with IEC/EN/UL/CSA 60950-1 or IEC/EN/UL/

CSA 62368-1 or a Class 2 circuit in accordance with NEC or CEC.

3Function and application

The sensor converts pneumatic pressure values (relative pressure) into electrical

signals, which can be used for control or regulating functions.Measurements are

carried out using a piezoresistive sensor element with a following electronic evalu

ation unit. Interfacing to the higher-level system is provided by 1 or 2 switching

outputs, an optional analogue output and an optional IO-Link interface.

The switching outputs can be configured for monitoring of a threshold value,

a pressure range or a differential pressure. The outputs can be set as PNP or NPN

and normally open (NO) or normally closed (NC). Via the IO-Link interface, process

values can be read out and parameters changed and transmitted to additional

devices.

3.1Operating statuses

Operating statusFunction

RUN mode–Basic status after the operating voltage is switched on

–Display of the current measured value

SHOW mode–Display of the current settings

EDIT mode–Setting or modification of parameters

TEACH mode–Acceptance of the current measured value to determine switching

points

Fig. 4

3.2Switching functions

Threshold value comparator for monitoring of a pressure threshold _|¯

FunctionNO (normally open)NC (normally closed)

Switching function:

–1 switching point (SP)

TEACH mode:

–2 teach-in points (TP1, TP2)

–SP = ½ (TP1+TP2)

TP1TP2

HY

1

0

Out

p

SP

TP1 TP2

SP

HY

1

0

Out

p

Fig. 5

Product specificaties