EXSYS EX-2346 Handleiding

Bekijk gratis de handleiding van EXSYS EX-2346 (2 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 6 mensen en kreeg gemiddeld 4.9 sterren uit 2 reviews. Heb je een vraag over EXSYS EX-2346 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

65

Die EX2346 ist ein Modul zur Umsetzung von USB 2.0 auf eine RS422/485 Schnittstelle mit --

FIFO 16C550 Port für den Anschluss von High Speed seriellen RS422/485 Peripherie Geräten -

(z.B. Modem, Plotter usw.). Die EX2346 ist mit einem USB 2.0 CStecker zum Anschluss an --

den PC und einem RS422/485 seriellen 9 Pin Stecker ausgestattet. Das USB Modul ist Hot -

Plug & Play fähig. Für die Einstellungen der I/O Adressen und Interrupts sind keine Jumper und

Einstellungen notwendig, da die Einstellungen automatisch vom System BIOS und bei der

Installation des Betriebssystems vorgenommen werden.

Kompatibilität:USB 1.1, 2.0 & 3.2

Betriebssysteme:Windows 9.x / ME / 2000 / XP / Vista / 7 / 8.x / 10 / 11 / Server 20xx /

Linux / MAC

Anschlüsse:1x USB 2.0 CStecker, 1x 9 Pin Stecker Seriell RS422/485--

Lieferumfang:2346, Adapter 9 Pin Buchse zu 5 Pin Terminal Block,EX-

2x Sechskantmuttern, Treiber CD, Anleitung

Zertifikate:

1

BESCHREIBUNG & TECHNISCHE DATEN

AUFBAU

Anleitun

Vers. 1.1 / 08.12.21

E234

USB 2.0 CStecker -

zum Anschluss an PC

S1: 9 Pin Stecker Seriell RS422/485-

2x Sechskantmuttern

CONNECTORS, STATUS LEDS & DIPSWITCH‘-

DIPSchalter-

HARDWAREINSTALLATION

Because there are large differences between PCs, we can give you only a general installation ’

guide for the EX-2346. Please refer your computers reference manual whenever in doubt.

1.-- Connect the EX2346 USB to the USB CPort at the your PC.

2.-If you would like to screw the serial cable to the 9 Pin connector of the EX2346, then

unscrew the screws (see Picture 1) and screw the supplied hexagon nuts into the holes on

the EX2346 (see Picture 2). Now you can attach the serial cable to the EX--2346.

USB 2.0 CPlug:-

Status LED‘s:

RXD

TXD

DIPSwitchPositionDescription-

1

ON (Factory Settings)2wire RS485 Mode--

OFF4wire RS485 or RS422 Mode---

2

ONReserved for features in future

OFF (Factory Settings)Reserved for features in future

3

ON120 Ohm TXD Termination Resistor is Enabled

OFF (Factory Settings)120 Ohm TXD Termination Resistor is Disabled

ON120 Ohm RXD Termination Resistor is Enabled

4

OFF (Factory Settings)120 Ohm RXD Termination Resistor is Disabled

DIPSwitch:-

DRIVER INSTALLATION

CLEANING

Windows

After the hardware installation Windows will recognize the device automatically and install the

drivers. If the driver shoul not be installed automatically, please insert the Driver CD into your

CD-Rom drive (e.g. Drive D:) and open the folder USB_to_IO/FTDIPlease select the folder „“.

with your operating system and install the driver (see Picture). Follow the hardware assistant

and finish the installation. Restart your PC in any case after installing the drivers.Important!

For cleaning please use only a dry fluff less cloth and remove the dirt with gently pressure. In

the area of the connectors please make sure that no fibres from the cloth remain in the connect-

ors. Attention! Never use a moist or wet cloth for cleaning!

CHECK INSTALLED DRIVER

Open the . Now you should see at >Device manager<„Ports (COM & LPT)USB“ and „-

Controller “the following new entry:

If you see this or a similar information the device is installed correctly.

Picture 1Picture 2

Remove the ScrewsInsert the Hexagon Nuts

3.Now set the DIP-Switch to the desired settings (see figure DIP-Switch on page 2).

4.When you are ready you can start your PC and continue with the point „Driver Installation.“

HARDWAREINSTALLATION

A12A11A10 A9A8A7A6A5A4A3A2A1

GNDRX2+RX2VBUSSBU1DVBUSTX1TX1+GND - - D+CC1 -

GNDTX2+TX2VBUSDSBU2VBUSRX1RX1+GND - CC2D+ - -

B1B2B3B4B5B6B7B8B9 B10B11B12

ANSCHLÜSSE, STATUS LEDS & DIPSCHALTER‘-

DB 9M RS422/485 Anschlussbelegung:-

DB9 (EX- 2346) DB9 (Endgerät)

1 TXD 1 TCD--

2 TXD+ 2 TXD+

3 RXD+ 3 RXD+

4 RXD- 4 RXD-

5 GND 5 GND

DB9 (EX-2346) DB9 (Endgerät)

1 DATA- 1 DATA-

2 DATA+ 2 DATA+

3 NC 3 NC

4 NC 4 NC

5 GND 5 GND

RS--422 und RS485 4Draht Anschlussbelegung-

RS--485 2Draht Anschlussbelegung

Product specificaties