Emko ECO PID+ Handleiding

Bekijk gratis de handleiding van Emko ECO PID+ (4 pagina’s), behorend tot de categorie Temperatuurregelaar. Deze gids werd als nuttig beoordeeld door 80 mensen en kreeg gemiddeld 4.9 sterren uit 7 reviews. Heb je een vraag over Emko ECO PID+ of wil je andere gebruikers van dit product iets vragen? Stel een vraag

3

2

1

45

6

Eco PID+, PID Temperature Control Un t�

- 4 d g t process (PV) and 4 d g t set (SV) d splay� �� ��

- Temperature sensor �nput (TC,RTD)

- Programmable ON/OFF, P, PI, PD and PID control forms

- Adaptat on of PID Coeff c ents to the system w th Self-Tune and Auto-Tune �� ��

- Programmable Heat ng or Coolng Funct ons for Control Output �� �

- Selectable Alarm Funct ons for Alarm Output�

- Ser al RS485 Commun cat on (opt onal)�� ��

Introduct�on Brochure. ENG EcoPID+ 01 V00 03/22

Easy Access D agram For Program Parameters�

Panel Mount ng�

Enter Password wth ncrement� �

or decrement buttons.

Approve password

w th Enter button�

Password Screen

Eco ser es temperature controllers are des gned for measurng and controll ng a ��� �

temperature value. They can be used n many appl catons wth ther TC and RTD �� ���

temperature measurement nput, mult-funct on control outputs, selectable alarm �� �

funct ons.�

They are ma nly used � �n glass, plast c, petro-chem stry, text le, automotve and mach ne �� ���

producton � ��ndustres. Accurate and advanced controll ng � �s performed wth selectable �

ON-OFF, P, PI, PD, PID and Self Tune/Auto Tune PID funct ons.�

SPECIFICATIONS

Process Input: Thermocouple (TC): J, K, R, S, T and L (IEC584.1)(ITS90)

Thermores stance (RTD): Cu-50 and PT-100 (IEC751)(ITS90)�

Measurement Range: Please refer to process �nput type select on � �n process menu

parameters secton.�

Accuracy:

Thermocouple (TC):( ± 0.25% of full scale or ± 3ºC, wh ch one � �s greater) ±1 d gt max. � �

Thermores stance (RTD):( ± 0.25% of full scale or ± 2ºC, wh ch one �� �s greater) ±1 d gt � �

max.

Cold Junct on Compensat on:�� Automat cally ±0.1°C/1°C�

L ne Compensat on:�� Max mum 10 Ohm�

Sensor Break Protect on:�Upscale

Sampl ng Cycle: �0.1 second

Input F lter:�Programmable

Control Form: ON/OFF, P, PI, PD or PID (Control form can be programmed by the user)

OUTPUT

Process Output:Relay (5A@250V at res stve load) or SSR Dr ver Output V� ��

(Max mum 10mA, Max. 12V )�Z

Alarm Output:Relay (5A@250V at res st ve load)V� �

SUPPLY VOLTAGE (It must be determ ned � �n order)

230V (±15%) 50/60Hz - 4VAV

115V (±15%) 50/60Hz - 4VAV

100-240V 50/60Hz - 4VAV

24V(±%15) 50/60Hz - 4VAV

24V (±%15) 50/60Hz - 4VAW

10...30V - 4W Z

DISPLAY

Process D splay:�16 mm Red 4 d gt LED Dsplay� ��

Set Value D splay:�9 mm Orange 4 d gt LED D splay� ��

Led Indcators:�PO1 (SSR Process Output Status Led), PO2 (Relay

Process Output Status Led), AL1, AL2 (Alarm Output Status Leds),

ºC, ºF LEDs

ENVIRONMENTAL RATINGS and PHYSICAL SPECIFICATIONS

Operat ng Temperature:�0...50ºC

Hum d ty :� �0-90%RH (none condensng)�

Mechancal Impacts: �1Joule (IK06)

Protect on Class: �NEMA 4X (IP65 at front, IP20 at rear)

We ght:�150 gr.

D mens on:�� 48 x 48 mm, Depth: 86,5 mm

Panel CutOut:46 x 46 mm

*1 -ON/OFF Hysteress parameter s not actve unless parameter s set as .�� ��

*2 - Soft Start parameters( , , ) s not act ve unless parameter s set as .� ��

*3 - Soft Start Control Output and Soft Start Control Tme parameters s not actve f parameter��� �

s set as .�

*4 -PID control parameters are not actve unless parameter s set as .� �

*5 -Alarm-2 parameters are not act ve f parameter s set as .� ��

*6 - Communcaton parameters are not actve on dev ces have no communcat on module.� ���� �

*7 -If s dfferent from 0 and user enters to program menu w thout enterng the password� ���

Prot menu s not shown.�

Note: User can ex t from any parameter screen w thout sav ng the values by pressng button. If �� ��

no operaton for 120 seconds, devce automatcally return to man screen. �� ��

Easy Access D agram For Sensor Break Output�

Value From Ma n Screen�

Change the sensor break

output value w th ncrement� �

or decrement buttons.

Press Enter button to save

new sensor break output value

and ext.�

Ma n ScreenMa n Screen� �

Note1: User can ext from parameter screen w thout savng the �� �

values by pressng button. If no operaton for 120 seconds, dev ce �� �

automatcally exts from parameter screen.� �

Note2: Sensor break output value can be adjusted on programmng �

secton too.�

Tune Operat on�

Start ng the Tune operat on� �

1- Enter to the parameter n menu and select �

or ,then press button for sav ng parameter and turn to man � �

screen. Or easly press button for 3 seconds* n ma n screen.�� �

2- Observe that bl nks n set dsplay.� ��

*Only Self Tune can be started by th s way.�

Cancel ng Tune operat on:� �

1- If sensor breaks;

2- If tune operaton can not be completed n 8 hours;� �

3- Whle heatng self tune s runn ng, f process value becomes ���� �

greater than process set value;

4- Whle cool ng self tune s runn ng, f process value becomes less ���� �

than process set value;

5- Whle tune operaton s runn ng, f user changes the process set �� ���

value;

6- Whle tune operaton s runn ng, f user changes the �� ���

parameter n menu; �

Then tune operat on s canceled, devce cont nues to run w th former � ����

PID parameters w thout chang ng PID parameters.� �

PID TEMPERATURE CONTROL UNIT

PID+

Eco

D mens ons� �

48 mm / 1.89 nch�

48 mm / 1.89 nch�

6 mm / 0.24 nch�80,52 mm / 3.17 nch�

Max mum 9 mm / 0.35 nch� �

1-Before mount ng the dev ce n your panel, �� �

make sure that the cutout s of the r ght sze.�� �

2- Check front panel gasket pos ton.� �

3-Insert the dev ce through the cutout. If the �

mount ng clamps are on the unt, put out them � �

before nsert ng the un t to the panel.� ��

4-Insert the mount ng clamps to the two of �

des gnated holes that located four sdes of � �

dev ce. �

5- Drag the mount ng clamps n d recton 5 �� � �

unt l the dev ce completely mmoble w thn the ����� �

panel.

6-In order to remove dev ce push on the �

mount ng clamp as shown w th arrow 6 and � �

pull back.

Access and Change Set Values

Press ncrement or decrement�

button to change process set value.

Press Enter button to save new

set value and return the man screen.�

Ma n ScreenMa n Screen��

Temperature Set Value Parameter (Default: 200) MODBUS ADDRESS: 40000

a

Note-1: User can ext from set value sect on wthout sav ng the values by pressng button. If no �� ���

operaton for 120 seconds, devce automatcally exts from Set Value secton.��� ��

Note-2: Set value can be adjusted between Set Value Low and Hgh Lm t ( - ).�� �

Press Program button

to access password screen.

Electrcal Wrngs�� �

Toreducethe effectof electrcalnoseon devce,lowvoltagelne (especallysensor� ����

�� ����nput cable) wrng must be separetely from hgh current and voltage lne. If possble,

use shelded cable and sheld must be connected to ground only one s de.� ��

c

Note-1: External Fuse s recommended.�

Note-2: Stranded cable cross sect on: 1,5mm², Sol d cable cross-sect on: 2,5mm²� ��

The str pp ng length s 7mm to 9mm.� ��

Note-3: Supply cables must comply w th the requ rements of IEC 60277 or IEC 60245.� �

It s adv sed to use a two-pole supply sw tch, desgnated for th s dev ce, w th open/� ���� ��

closed post ons marked, n order to cut the power. It must be placed on the supply � ��

� ��nput of the dev ce at a place where the user can easly reach.

V External fuse must be on phase connect on of the supply nput.� �

Z External fuse must be on (+) l ne connect on of the supply nput.� ��

Make sure that the power supply voltage range s su table for the dev ce.� ��

Sw tch on the power supply only after all the electr cal connect ons are n place.��� �

1

2

3

4

5

6

7

8

9

10

11

12

13

14

PO1

(Process Output 1)

SSR Output

12V

Max. 10mA

C

NO

NO

AL1

(Alarm Output 1)

AL2 / PO2

(Alarm Output 2 or

Process Output 2)

Process

Input

5A@250V

5A@250V

Ser al Commun caton�� �

(RS485, Modbus RTU)A+

B-

PID+

Eco

PT-100

TC

Supply

Sw tch�

L

N

Supply

Voltage

1A T

Fuse

NOTE-1

AL1 / PO2

(Alarm Output 1 or

Process Output 2)

Process

Input

8

9

10

11

C

NO

5A@250V

12

13

14

PT-100

TC

The Devce �

w th Two Relays�

The Devce �

w th One Relay�

Çalma Ekranış ı

*1

*5

*2

*4

*2,3

*2,3

*7*6

Product specificaties