Electro Harmonix LPB-3 Handleiding
Bekijk gratis de handleiding van Electro Harmonix LPB-3 (4 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 56 mensen en kreeg gemiddeld 4.5 sterren uit 28.5 reviews. Heb je een vraag over Electro Harmonix LPB-3 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/4
POWER SUPPY REQUIREMENTS:
Voltage: 9VDC Current: 120mA Polarity: Center-Negative
This device comes equipped with an Electro-Harmonix 9.6DC-200 power supply. Use of the wrong adapter
or a plug with the wrong polarity may damage the device and void the warranty. Do not exceed 12VDC on the
power plug. Power supplies rated for less than 150mA can cause the device to act unreliably.
Operating Instructions
Insert the output plug from the supplied 9VDC AC Adapter into the power jack
at the top of the LPB-3. Connect an instrument cable from your instrument to
the Input jack of the LPB-3. Connect an instrument cable between the Output
jack and a suitable amplier or mixer. Press the footswitch to engage the
LPB-3 and light the LED.
A good starting point is to set the knobs to their 12 o'clock positions and the
MAX and Q toggle switches to their lower positions. Increase the BOOST knob
for a noticeable increase in volume compared to bypass mode. Play some of
your favorite licks then further tweak the knobs and switches to dial in your
perfect setting.
Welcome to the Electro-Harmonix LPB-3, a compact booster pedal
capable of delivering up to 33dB of clean gain. Powerful Treble, Mid,
and Bass EQ controls allow for wide variation in tone shaping. Addition-
ally, the LPB-3 boasts extended +/-15V power rails and switchable
true or buffered bypass modes. Whether your sound needs just a little
nudge, a boost to line level for DAW recording, or to send your
amplier into saturated bliss, the LPB-3 has you covered.
- 2 -
Controls and Connections
1. PRE-GAIN Knob Adjusts clean input gain from 0dB (unity) to 20dB before
the signal hits the EQ circuitry. Use PRE-GAIN in conjunction with BOOST and
MAX to ne-tune the total output volume and gain through the LPB-3.
Pro Tip: If the EQ knobs are set in the boost half of their range, signal clipping
can be avoided by decreasing PRE-GAIN. If the EQ settings are set to cut, turn
up PRE-GAIN for more volume.
2. BOOST Knob Sets the output level of the LPB-3, basically working like a
volume control.
3. MAX Switch Boosts the gain at the output stage, and sets the maximum gain
of the LPB-3—from Input to Output—to either 33dB or 20dB. Set MAX to 20dB
for greater dynamics; set MAX to 33dB to drive the signal harder and poten-
tially send your amp into saturation.
Product specificaties
| Merk: | Electro Harmonix |
| Categorie: | Niet gecategoriseerd |
| Model: | LPB-3 |
Heb je hulp nodig?
Als je hulp nodig hebt met Electro Harmonix LPB-3 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd Electro Harmonix
5 Augustus 2025
5 Augustus 2025
5 Augustus 2025
5 Augustus 2025
5 Augustus 2025
4 Augustus 2025
4 Augustus 2025
4 Augustus 2025
4 Augustus 2025
4 Augustus 2025
Handleiding Niet gecategoriseerd
- FeinTech
- Orange
- InFocus
- Primera
- Peterson
- W'eau
- Ade
- Hager
- Musicmate
- Baby Jogger
- Sacrament
- MBM
- Expobar
- Bulman
- Akrobat
Nieuwste handleidingen voor Niet gecategoriseerd
14 September 2025
14 September 2025
13 September 2025
13 September 2025
13 September 2025
13 September 2025
13 September 2025
13 September 2025
13 September 2025
13 September 2025