Draper 78775 Handleiding
Draper
Soldeermachine
78775
Bekijk gratis de handleiding van Draper 78775 (4 pagina’s), behorend tot de categorie Soldeermachine. Deze gids werd als nuttig beoordeeld door 21 mensen en kreeg gemiddeld 5.0 sterren uit 11 reviews. Heb je een vraag over Draper 78775 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/4
HEAT GUN
78775
MICRO BUTANE
EN
Original Instructions
Version 2 – March 2023
1. Specication
2. HealthandSafetyWarnings
• Observe all standard safety precautions and good
practices when working with naked ames and
ammable fuels.
• Keep the work environment clear and well-lit, with
bystanders at a safe distance.
• Keep this product out of reach of children at all times.
• ALWAYS wear appropriate eye and face protection and
protective gloves when using this product.
• Check the heat gun for damaged, clogged or corroded
parts and leaks before every use.
− use the product if it is damaged or leaking DO NOT
in any way; contact Draper Tools for repair and
replacement options.
− If you suspect that the product is leaking gas, move
it to an external environment immediately.
The product can be tested for leaks by Important:
dabbing soapy water solution on joints and
connections while gas is added to or stored in the
product. Leaks will create a steady feed of soapy
bubbles at the breach point.
• Use ONLY in well-ventilated environments.
• use this product in environments where paint DO NOT
fumes, solvents and other ammable materials are
present.
• Use only good quality butane gas.
WARNING!Butanegasishighlyammable;
handle it carefully and in accordance with the
instructions on the canister.
• During rst use, allow a few minutes for the product to
settle once ignited before directing it towards the
workpiece.
WARNING! The metal parts of the heat gun
becomeveryhotduringuse.DONOTtouchthe
barrelorworkpieceuntiltheyhavecooled
thoroughly.
WARNING!Avoidcontactwithskin,clothingor
otherammablematerials.
• leave the product running while unattended.DO NOT
• expose the product to temperatures above 49°C DO NOT
(120°F) or to prolonged periods of sunlight.
• switch o the product while it is not in use and ALWAYS
ensure that the control lever remains in its lowest
position.
• After each use, ensure that the ame is fully
extinguished, the control lever is in its lowest position
and the product has completely cooled before storing.
• attempt to disassemble or modify this tool in DO NOT
any way.
• refuel outside.ALWAYS
• smoke while refuelling.NEVER
WARNING! This product is not insulated against
electricity.NEVERusethisproductonworkpieces
that are connected to electrical power.
WARNING! ALWAYS ensure that the control
leverremainsintheopositionafteruse.
Ifthefuelsupplyisre-engaged,residual
heat can cause reignition without operating
theignitionbutton.Oncethetoolhas
cooled,followthenormalignition
procedure to reignite.
Stock No. 78775
Part No. GT9
Fuel type Butane
Approx. temperature ≤ 450°C
Operating time (one gas
lling)
20 mins approx. at mid
setting
Dimensions W 90 × H 35 × Ø 20mm
Weight (80% gas ll) 51g
Read this manual in full before using this product and
retain it for future use. Always use the latest version of the
manual. Please visit drapertools.com/manuals for the
latest version of this manual.
3. Refuelling
WARNING!Beforellingtheproduct,ALWAYS
ensurethatthecontrolleverisinitslowest
position.ONLYusebutanegastofueltheproduct.
Important: This product is not shipped with butane gas
and MUST be fuelled before use.
1 Fig.
(A)
1. Turn the heat gun upside-down and push the butane
can nozzle rmly into the lling valve (A).
2. Filling begins automatically and takes only a few
seconds.
The fuel level can be viewed through the window (B)
beneath the control lever (C).
3. Allow a few minutes after lling for the gas in the
product to stabilise.
WARNING!Allowescapedgastodispersebefore
lighting the heat gun. NEVER light the product
whileagascanisterisinsertedintothelling
valve.
4. IgnitionandUse
WARNING! Keep your hands and face away from
thebarrelwhenignitingandoperatingthe
product.Griptheheatgunbythehandleonly.
1. Fuel the product and allow the gas to settle.
2. Move the control lever (C) to the ON position to start
the fuel supply.
2 Fig.
(C)
(B)
3. Depress the ignition button (D) repeatedly until the
ame is lit.
3 Fig.
(D)
4. Adjust the size and temperature of the ame using
the control lever.
5. Allow approximately 30 seconds for the ame to
reach temperature, then direct the heat gun safely
towards the workpiece.
6. Wait for the gauze (E) to glow, indicating that
operating temperature has been reached.
7. Direct the heat gun at the workpiece to heat it,
keeping your hands away from the barrel and the
vents on the side of the heat gun.
WARNING! DO NOT hold the heat gun too
closetotheworkpiece.Heatreectedback
towards the heat gun may damage the heat
gun or cause injury. NEVER allow the heat
guntotouchtheworkpiece.
8. To switch o the heat gun, move the control lever
fully to the left and allow several minutes for the
gauze to cool.
– The clear lid (E) can be used as a stand while
cooling.
9. While the gauze is still hot and glowing, the heat gun
can be reignited by moving the control lever out of
the OFF position.
4 Fig.
(E)
20
min
REFILLABLE
Important: Avoid using the product in sideways or inverted
orientations as this may interrupt the ow of fuel to the
ame.
WARNING!ALWAYSensurethatthecontrollever
remainsintheopositionafteruse.Ifthefuel
supplyisre-engaged,residualheatcancause
reignitionwithoutoperatingtheignitionbutton.
Oncethetoolhascooled,followthenormal
ignition procedure to reignite.
5. MaintenanceandDisposal
WARNING!ALWAYSensurethatthecontrollever
is in the OFF position and that the heat gun is
completelycoolbeforemaintainingorstoringthe
product.
• Keep the barrel clean and dry.
− Use a dry cloth ONLY to clean the barrel.
− use solvents or other aggressive chemicals DO NOT
to clean the product as they may damage plastic or
insulated parts.
• Keep the air vents of the barrel free from dust and
obstructions.
• Store the product in a clean, cool and dry location, out
of direct sunlight and out of reach of children.
• At the end of its working life, dispose of the product
responsibly and in line with local regulations. Recycle
where possible. Exhaust the fuel before disposing of the
product and dispose of butane separately and
responsibly.
6. ExplanationofSymbols
Read the instruction leaet
Max. potential operating time per refuel
Operating temperature
Rellable gas
Keep out of the reach of children
450°C
Product specificaties
| Merk: | Draper |
| Categorie: | Soldeermachine |
| Model: | 78775 |
Heb je hulp nodig?
Als je hulp nodig hebt met Draper 78775 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Soldeermachine Draper
3 Juni 2025
2 Juni 2025
2 Juni 2025
Handleiding Soldeermachine
- UNIMIG
- Yato
- Epcom
- Ersa
- Weller
- Maestro
- VOREL
- Mag-Torch
- RIDGID
- Gude
- Craftsman
- Vigor
- Powerplus
- Fixpoint
- Stamos
Nieuwste handleidingen voor Soldeermachine
5 Juli 2025
3 Juli 2025
17 Juni 2025
16 Juni 2025
23 Mei 2025
20 Mei 2025
20 Mei 2025
15 Mei 2025
15 Mei 2025
15 Mei 2025