Draper 23707 Handleiding
Draper
Meetapparatuur
23707
Lees hieronder de 📖 handleiding in het Nederlandse voor Draper 23707 (4 pagina's) in de categorie Meetapparatuur. Deze handleiding was nuttig voor 5 personen en werd door 3 gebruikers gemiddeld met 5.0 sterren beoordeeld
Pagina 1/4
23707
12V DIGITAL
BRAKE FLUID
TESTER
WITH PRINTER
EN
Original Instructions
Version 1 – March 2024
User Manual for: 12V Digital Brake Fluid Tester with Printer
Stock No.: 23707
Part No.: BFT4
Read this manual in full before using this product and
retain it for future use. Always use the latest version of the
manual. Please visit for the drapertools.com/manuals
latest version.
1. Intended Use
This product is designed to check the water content of
brake îœ uid quickly and eciently. Fitted with a printer
for printing o the test results, essential for safety checks
and servicing.
Any other application beyond the conditions established
for use will be considered misuse. Draper Tools accepts no
responsibility for improper use of this product.
2. Specication
Stock No: 23707
Part No: BFT4
Compatible Brake Fluid: Dot 3 / Dot 4 / Dot 5.1
Power Supply Required: DC 12V Battery
Tester Length: 235mm
Tester Diameter: 90mm
Flexible Probe Length: 260mm
Flexible Probe Diameter: 5mm
Net Weight: 524g
Positive/Negative Lead Length: 270mm
Paper Dimension (L X W): 57 X 30mm
Operating Temperature: 0 - 50°C
3. Health and Safety Information
Important: Read all the Health and Safety instructions
before attempting to operate, maintain or repair this
product. Failure to follow these instructions may result in
injury or damage to the user or the product.
• ONLY trained and competent personnel may operate
this device.
• use the tester for any other purpose than which DO NOT
it is designed for.
• Keep children and unauthorised person away from the
work area.
CAUTION! Always wear safety googles and gloves
when working with brake îœ uid. If the brake îœ uid
comes into contact with skin, wash o immediately
and seek medical advice if necessary.
• clean the tester probes after every use.Always
• DO NOT use this device if the tester, clamps or probe are
damaged in any way.
• attempt to repair this device; it contains no DO NOT
user-serviceable parts.
• Only use a DC 12V vehicle battery, DO NOT use 24V or
any other voltage with this tester.
• short contact either the positive or negative DO NOT
terminals of the battery.
4. Identication
1. Test probe
2. Display screen
3. Printer compartment
4. Positive (+) red clamp
5. Negative (-) black clamp
6. Conrm button
7.
/decrease button
(8)
/reset button
(9)
/increase button
– 2 –
(6)
(7)
(9)(8)
(2)
(3) (4) (5)
(1)
6. Using the Printer function
3 Fig.
1. Insert the print paper roll into the printer
compartment (3).
2. After carrying out the brake îœ uid test press the conrm
button to enter the print mode.
3. The date and Vin number (last 4 digits) can be printed.
Press the
/decrease button (7) and /increase
button (9) to select each digit, press the conrm button
after each selection.
4. Once selection completed press the conrm button
again to print out the test results.
7. Maintenance, Storage and
Disposal
• After use clean the probes to remove any brake
îœ uid residue.
• Store the device in a cool, clean and dry environment,
out of direct sunlight and out of reach of children.
• Calibration - To conrm the accuracy of the tester,
carry out a test using clean water. If the tester is working
correctly the temperature reading will be 100°C/212°F.
• At the end of its working life, dispose of the product
responsibly and in line with local regulations.
Recycle where possible. dispose of this product DO NOT
with domestic waste; most local authorities provide
appropriate recycling facilities.
Warranty
12 months – Visit drapertools.com/warranty
for full details.
– 3 –
5. Testing The Brake Fluid
1. Connect the clamps to a 12V vehicle battery – ensuring
the positive (+) red clamp (4) is connected to the positive
terminal and the negative (-) black clamp (5) to the
negative terminal.
1 Fig.
2. Press the
/decrease button (7) and /increase
button (9) to select the brake îœ uid type to test.
Then press the conrm button (6).
3. Dip the tester into the brake îœ uid until the probes are
fully submerged and press the conrm button (6).
2 Fig.
4. The îœ uid quality results will be displayed on the screen
(2) examples below: -
DOT 3
3.0% <X%
DOT 4
2.5 ≤ X% ≤ 3.0%
DOT 5.1
X% < 2.5%
Need to
replace
immediately
Risk Exist
Keep caution
Available to
use continually
Monitor Good to use
5. To reset or return to the previous screen press the reset
button (8).
(7)
(6)
(9)
(8)
(3)
Product specificaties
| Merk: | Draper |
| Categorie: | Meetapparatuur |
| Model: | 23707 |
Heb je hulp nodig?
Als je hulp nodig hebt met Draper 23707 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Meetapparatuur Draper
6 Juni 2025
5 Juni 2025
4 Juni 2025
3 Juni 2025
3 Juni 2025
3 Juni 2025
2 Juni 2025
2 Juni 2025
30 Mei 2025
30 Mei 2025
Handleiding Meetapparatuur
- Meetapparatuur Ade
- Meetapparatuur MSW
- Meetapparatuur Duux
- Meetapparatuur Kopp
- Meetapparatuur Oscium
- Meetapparatuur Wentronic
- Meetapparatuur Eltako
- Meetapparatuur Blebox
- Meetapparatuur DriveTest
- Meetapparatuur Microlife
- Meetapparatuur Honeywell
- Meetapparatuur Grohe
- Meetapparatuur Cliff
- Meetapparatuur Water-i.d.
- Meetapparatuur Corentium
Nieuwste handleidingen voor Meetapparatuur
6 Juni 2025
3 Juni 2025
3 Juni 2025
25 Mei 2025
24 Mei 2025
24 Mei 2025
24 Mei 2025
23 Mei 2025
23 Mei 2025
23 Mei 2025