Digital Watchdog MegaPix DWC-MV82DIVT Handleiding

Digital Watchdog Bewakingscamera MegaPix DWC-MV82DIVT

Lees hieronder de 📖 handleiding in het Nederlandse voor Digital Watchdog MegaPix DWC-MV82DIVT (2 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 10 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2

DWC-MV82DiVT

Template

Sheet

Resetting the camera: To reset the camera, use the tip of a

paper clip or a pencil and press the reset button. Pressing the

button for ﬁve (5) seconds will initiate a camera-wide reset of

all the settings, including network settings.

Reset

Button

Ethernet

Cable

Quick Start Guide Quick Start Guide

WHAT’S IN THE BOX

Quick setup

guide 1 Set Waterproof

cap 1 Set

Mounting

template

for bolt and

nuts

installation

1 Set Torque

wrench 1 Set

Mounting

template

for plate

installation

1 Set

Screws and

plastic

anchors

3pcs

1 Set

Bolt and

nuts 2pcs 1 Set

Moisture ab-

sorber and

absorber

guide

1 Set

Metal

mounting

plate

1 Set

1. The mounting surface must withstand ﬁve times the

camera weight.

2. Do not let the cables get caught in improper places or the electric

line cover can be damaged. This may cause a short or ﬁre.

3. For the installation process, remove the dome cover from the

camera module by loosening the three (3) screws on the dome.

Use the wrench provided with the camera.

4. Install the moisture packet in the base of the camera’s lens.

a. Remove the moisture absorber from the packaging.

b. Cut the card and folder along the dotted line.

c. Place the moisture absorber behind the camera’s lens module.

Pass the wires through the mount bracket and make all necessary

connections.

1. NETWORK CONNECTIONS – If you are using a PoE Switch,

connect the camera using an Ethernet cable for both data and

power.

2. NETWORK CONNECTIONS – If you are using a non-PoE switch,

connect the camera to the switch using an Ethernet cable

for data transmission and use a power adapter to power the

camera.

STEP 1 – PREPARING TO MOUNT THE CAMERA

STEP 3 – INSTALLING THE CAMERA

STEP 2 – CABLING THE CAMERA TO

EXTERNAL DEVICES

1. Attach the main body to the mount bracket by tightening the

lock screw.

2. For soft installation surfaces, use the included metal mount plate. Fix

the mount plate on the mounting surface using the included screws.

Then, press the bottom case onto the mount plate. The three bezels

on the case will align and snap lock onto the plate.

3. To use the camera’s water proof wiring:

a. Install the LAN cable into .

b. will be assembled

to with a 1/4 turn.

c. Thread tightly to .

NOTE: To ensure moisture seal, make sure the o-ring is in place

between and . In extreme environments use of an

outdoor rated sealer is recommended.

a b

NOTE: When using the waterproof cap, crimp the RJ45

connector after passing the cable through the

waterproof cap.

Power requirements Power consumption

DC 12V, PoE (IEEE

802.3af Class 3).

(Adapter not included)

DC12V: max 4.3W

PoE: max 6.2W

Tel: +1 (866) 446-3595 / (813) 888-9555

Technical Support Hours:

9:00AM – 8:00PM EST, Monday thru Friday

digital-watchdog.com

Attention: This document is intended to serve as a quick reference for initial

set-up. It is recommended that the user read the entire instruction manual for

complete and proper installation and usage.

NOTE: Download all your support materials and tools in one place

1. Go to: http://www.digital-watchdog.com/resources

2. Search your product by entering the part number in the

search bar. Results for applicable ‘Search by Product’

part numbers will populate automatically based on the

part number you enter.

3. Click . All supported materials, including manuals ‘Search’

and quick start guide (QSGs) will appear in the results.

Power

Ethernet

Cable

WARNING DO NOT TOUCH THE SURFACE OF THE

BUBBLE. CleanView™ Hydrophobic Dome

Coating has been applied to the camera’s dome.

5. Remove the protective ﬁlm between the dome and the camera

module.

6. Remove the screw hole caps as shown in the image below. If you

are mounting the camera using the mounting plate, you do not

have to remove these screws.

7. Using the mounting template sheet or the camera itself, mark and

drill the necessary holes in the wall or ceiling.

Default Login Information: admin | admin

Rev Date: 07/19

Speciﬁcations and pricing are subject to change without notice.

STEP 3 – INSTALLING THE CAMERA (CONT.)

4. Adjust the camera’s pan, tilt and position to achieve the desired

view. The cameras’ max angles are:

Pan: 0° ~ 345°

Tilt: 0° ~ 75°

Rotation: 0° ~ 375°

5. To adjust the camera’s focus and zoom:

a. Unlock the zoom or focus screws by

rotating them counter-clockwise.

b. Adjust the zoom and focus screws

at the base of the camera module

to achieve a clear image.

c. Tighten the screws and close the front

case by rotating it clock-wise.

6. Once the installation is complete, remove the protective ﬁlm from

the camera’s dome cover.

7. Assemble the dome cover over the camera body and detach the

protecting ﬁlm from the dome bubble.

Installation using Mount Bolt and Screws:

1. Using the template sheet, make and drill the cabling holes on the

wall/ceiling.

2. Secure the two long mounting screws to the camera’s base.

3. Pass the wires through the mount bracket and make all

necessary connections.

4. Mount the camera to the mounting surface by using the 2

mounting nuts. Rotate the locking discs over the screws until the

camera is held tightly from the mounting surface.

NOTE: The camera’s maximum tilting angle is 75°

WARNING DO NOT TOUCH THE SURFACE OF THE

BUBBLE. CleanView™ Hydrophobic Dome

Coating has been applied to the camera’s dome.

Quick Start Guide

STEP 5 – WEB VIEWER

The GUI display may dier by camera models.

STEP 6 – DW IP FINDER™

Thumbnail view

Firmware version

DHCP status

Camera’s uptime

Open IP conﬁguration

settings

Ping camera

Port information

Gateway address

Netmask address

Camera’s MAC address

Filter results

Scan network

Select network to scan

Show/hide thumbnail view

Refresh thumbnail view

Bulk password assignment

Bulk IP assignment

Firmware upgrade

Camera’s name

Camera’s IP address

Part number

Use the DW IP Finder™ software to scan the network and detect all MEGApix® cameras, set the camera’s network settings or access the camera’s web client.

Network Setup

1. To install the DW IP Finder™, go to:

http://www.digital-watchdog.com

2. Enter “DW IP Finder” on the search box at the top of the page.

3. Go to the “Software” tab on the DW IP Finder™ page to

download the installation ﬁle.

4. Follow the installation to install the DW IP Finder™. Open the

DW IP Finder™ and click ‘Scan Devices’. It will scan the selected

network for all supported devices and list the results in the

table. During the scan, the DW® logo will turn gray.

‘Port forwarding’ has to be set in your

network’s router for external access

to the camera.

Select DHCP to allow the camera to receive its IP address

automatically from the DHCP server.

Select “Static” to manually enter the camera’s IP address, (Sub)

Netmask, Gateway and DNS information.

* The camera’s IP must be set to Static if connecting to

Spectrum® IPVMS

Contact your network administrator for more information.

Default TCP/IP information: DHCP

5. When connecting to the camera for the ﬁrst time, a password

must be set. To set up a password for your new camera:

a. Check the box next to your new camera from the IP Finder’s

search results. You can select multiple cameras.

b. Click “Bulk Password Assign” on the left.

c. In the pop-up window, enter admin/

admin in the current username and

password ﬁelds. Enter a new

username and password to the right.

d. Press “change” to apply all changes.

6. Select a camera from the list by

double-clicking on the camera’s image

or clicking on the ‘Click’ button under

the IP Conf. column. The pop-up

window will show the camera’s current

network settings, allowing admin users

to adjust the settings as needed.

7. To access the camera’s web page,

go to the IP Conﬁg page and click on

‘View Camera Website’.

8. To save the changes made to the

camera’s setting, input username

and password of the camera and

click Apply.

NOTE: Please see the full product manual for web viewer setup,

functions and camera settings options.

NOTE: Some menu options may not be available based on the

camera model. See the full manual for more information.

Once the camera’s network settings have been setup properly, you

can access the camera’s web viewer using the DW IP Finder™.

To open the camera’s web viewer:

1. Find the camera using the DW IP Finder™.

2. Double-click on the camera’s view in the results table.

3. Press the ‘View Camera Website’. The camera’s web viewer will

open up in your default web browser.

4. Enter the camera’s username and password you setup in

the DW IP Finder™. If you did not setup a new username and

password via the DW IP Finder™, you will not be able to view

video from the camera. A message will direct you to setup a

new password for the camera in order to view video.

5. When accessing the camera for the ﬁrst time, install the VLC

player for web ﬁles in order to view video from the camera.

Product specificaties

Merk:	Digital Watchdog
Categorie:	Bewakingscamera
Model:	MegaPix DWC-MV82DIVT

Heb je hulp nodig?

Als je hulp nodig hebt met Digital Watchdog MegaPix DWC-MV82DIVT stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Bewakingscamera Digital Watchdog

Digital Watchdog Star-Light Plus DWC-B6853WTIR Handleiding

17 Januari 2024

Digital Watchdog MegaPix DWC-MVT4WiA Handleiding

17 Januari 2024

Digital Watchdog DW-VMAXD1 Handleiding

17 Januari 2024

Digital Watchdog DWC-MC352 Handleiding

17 Januari 2024

Digital Watchdog Star-Light DWC-V4363TIR Handleiding

17 Januari 2024

Digital Watchdog MegaPix IVA+ DWC-MPV85WIATW Handleiding

17 Januari 2024

Digital Watchdog Star-Light Plus DWC-B6563WTIR650 Handleiding

17 Januari 2024

Digital Watchdog MegaPix CaaS DWC-MF4WI4C2 Handleiding

17 Januari 2024

Digital Watchdog Star-Light Flex DWC-VS753WT Handleiding

17 Januari 2024

Digital Watchdog VMAX AHD CORE DW-VAC42T Handleiding

17 Januari 2024

Handleiding Bewakingscamera

Nieuwste handleidingen voor Bewakingscamera

Aqara Camera Hub G2H Handleiding

28 April 2024

Iiquu Dummy Dome Camera Handleiding

28 April 2024

Sony SNC-VB640 Handleiding

26 April 2024

Sony SNC-EB642R Handleiding

26 April 2024

Sony SNC-VB642D Handleiding

26 April 2024

Sony SRG-HD1 Handleiding

26 April 2024

Sony SNC-ZM550 Handleiding

26 April 2024

Sony SNC-EM642R Handleiding

26 April 2024

Sony SNC-EM641 Handleiding

26 April 2024

Sony SNC-ZB550 Handleiding

26 April 2024