Diamond Audio HXM1200.1D Handleiding
Diamond Audio
Receiver
HXM1200.1D
Lees hieronder de š handleiding in het Nederlandse voor Diamond Audio HXM1200.1D (10 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 7 personen en werd door 4 gebruikers gemiddeld met 5.0 sterren beoordeeld
Pagina 1/10
A U D I O
A U D I O
H X M S e r i e sH X M S e r i e s
DIGITAL AMPLIFIERSDIGITAL AMPLIFIERS
HXM800.2D/HXM800.4D/HXM800.1D
HXM1200.1D/1200.6D
HXM800.2D/HXM800.4D/HXM800.1D
HXM1200.1D/1200.6D
19
WARRANTY
INTRODUCTION
2
Congratulations, you have just purchased one of the finest mobile audio products on the
market. Diamond Audio products represent the latest advances in acoustic technology in
sound reproduction for your vehicle. Diamond Audio products are designed, developed, and
engineered in the USA using the latest innovative materials and components to provide the
finest sound reproduction possible. Every Diamond Audio product has been verified and
tested to ensure the best sounding and most reliable product on the market, if installed
properly .Diamond Audio products will provide many years of the ultimate listening experience.
Please note that prolonged exposure to sound pressure levels in excess of 100dB can cause
permanent hearing loss. Using Diamond Audio products can exceed that level so please
exercise restraint in its operation in order to preserve your ability to enjoy its high fidelity sound
for many years to come.
Diamond Audio recommends our products be professionally installed by an authorized
Diamond Audio dealer to achieve the best possible system recommendation and installation.
This will ensure a true Diamond Audio listening experience and sound you would expect from
Diamond Audio products. With proper validation, using a Diamond Audio Retialer for installation,
your newly purchased amplifier, Diamond Audio will extend the product warranty from one year
to Two Years!!
Go ahead, Hear the Music
THIS WARRANTY IS NOT TRANSFERABLE AND APPLIES ONLY TO THE ORIGINAL PURCHASER OF THIS PRODUCT
IN ITS ORIGINAL INSTALLATION. Original purchaser must reside in the United States and be able to provide proof of
purchase and installation with the sales receipt and completion of online regoistration from the authorized DAT retailer that
sold and installed the product.
Should a manufacturing defect occur during above said warranty period, DAT will replace or repair the defective product
with a product of the same or equivalent value and performance, at DATās discretion.
Damage or failure caused by any of the following is not covered under this warranty policy: negligence, improper use,
abuse, product modification, unauthorized repair attempts, accident, acts of God, misrepresentations by DAT retailers, and
improper/inadequate packaging during return shipping.
Warranty is void if serial numbers have been removed, altered or defaced.
HOW TO OBTAIN WARRANTY SERVICE
In the event a DAT product should require service, you should visit the authorized DAT retailer you purchased the product
from and they can expedite your claim. All claims must fall into the guidelines listed above and be accompanied by a copy of
the original sales and installation receipt from that authorized DAT retailer.
Product returned for warranty service must be freight-prepaid, properly packaged and clearly marked with the Return
Authorization (RA) number issued by DAT. Any product returned to DAT that is improperly packaged, does not have a
RA number clearly marked on the package, or never received a RA number may be refused upon delivery. DAT does not
assume responsibility for lost or misdirected product.
Repair or replacement under this warranty is the exclusive remedy of the consumer. DAT shall not be liable for any
incidental or consequential damages for breach of any expressed or implied warranty on this product. Some states do not
allow the exclusion or limitation of incidental or consequential damages, or allow limitations on how long an implied warranty
lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may
also have other rights that may vary from state to state.
Customers outside the United States should contact their local sales office to obtain information on pricing, exchange unit
availability, instructions, service and warranty/non-warranty replacement or repair.
Diamond Audio Technologies
1225 E.7th ST
LOS ANGELES,CA 90021
Tel: 213-261-4161
Fax: 213-947-4767
Web: diamondaudio.com
Service/Tech Support:
213-261-4161
Tech Support Email
techsupport@diamondaudio.com
Diamond Audio Technologies (DAT), a division of CV & DA Holdings Incorporated, warrants this product to be free from
defects in material and workmanship for a period of one (1) year from the original date of purchase, provided it was
purchased from an authorized DAT retailer within the United States. Product warranty period starts at the date of
purchase or one year past the manufacture date whichever is first. However, upon purchase and completion of the
on-line registration and installation by an authorized DAT dealer you warranty period will be extended to two (2) years.
This warranty extension offer will only be recognized upon completion of the on-line registration of your product within
thirty (30) days of the date of purchase.
18
3
RMS Power (1Ī©) 800 W X 1 RMS 1200 W X 1 RMS
RMS Power (2 Ī©)
550 W X 1 RMS
350 W X 1 RMS
850 W X 1 RMS
550 W X 1 RMS
RMS Power (4 Ī©)
Power Rating
11.72 x 5.27 x 1.75
297.6 x 133.9 x 44.5
HXM800.1D HXM1200.1D
Power Supply Full PWM Full PWM
Power Supply Threshold 10.0VDC -
17.0VDC
10.0VDC -
17.0VDC
Distortion
THD (1KHz @4Ī©) 0.05% 0.07%
S/N Ratio (A weighted @1W) -77.2dBA --77.4dBA
S/N Ratio (A weighted @ FP) -98.9dBA -97.4dBA
Input Sensitivity
Low Input Level 0.2mV - 10.0V 0.2mV - 10.0V
High Input Level
YES - UP to 25 W RMS YES - UP to 25 W RMS
Input Impedance
Low Input Level 22 KĪ© 22 KĪ©
Crossover (-12dB/Oct)
Variable High-Pass N/A N/A
PRODUCT SPECIFICATIONS
Variable Low-Pass
Variable Sub-Sonic
Fuse Ratings
30Hz - 300Hz
10Hz - 55Hz
30Hz - 300Hz
10Hz - 55Hz
Power Supply
Output Stage
Output Impedance 0.047Ī© 0.047Ī©
Damping Factor (50Hz @ 4ā¦)
>250 >250
Idle Current (0.7A) (0.7A)
ATC N/A N/A
Dimensions
Lenght x Width x Height (inches)
Lenght x Width x Height (mm)
Bandwidth (-3dB) 10Hz-350Hz 10Hz-350Hz
Topology MonoBlock Class D
Type
MonoBlock Class D
MODEL:
8.56 x 5.27 x 1.75
217.6 x 133.9 x 44.5
High Input Level
22 KĪ© 22 KĪ©
WARNING:
Prolonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss.
Cerwin Vega Mobile ampliļ¬ers can exceed that level so please exercise restraint when listening and enjoying your new ampliļ¬er.
GENERAL PRECAUTIONS
ā¢This unit is designed for negative ground 12V DC operation only.
ā¢Total system impedance must not be less than 2ohms, in a bridged OR stereo conļ¬guration
ā¢Avoid installing the unit where:
- It would be subject to high temperatures, such as from direct sunlight or hot air from the heater.
- It would be exposed to rain or moisture.
- It would be subject to dust or dirt.
ā¢Do not cover the unit with carpet or wires.
ā¢Do not use the unit with a weak auto battery. Optimum performance depends on a normal battery supply voltage.
ā¢For safety reasons, keep the volume of your car audio system moderate while driving your vehicle so that you can still hear
normal trafļ¬c sounds outside your car.
ā¢There is NO speaker level input connector, you can cut RCAās and solder the wires and connect directly thru low level input(RCA)
MOUNTING PRECAUTIONS
Although Cerwin Vega Mobile ampliļ¬ers incorporate heat sinks and protection circuits, mounting the ampliļ¬er in a tight space
without any air movement can still damage internal circuitry over time. Choose a location that provides adequate ventilation
around the ampliļ¬er. For easy system set-up, mount the ampliļ¬er so the side panel controls will be accessible after
installation. To increase thermal run times on low impedance loads, an additional fan is recommended, remember any moving
air across the ampliļ¬er will reduce heat.
In addition, observe the following precautions:
1. Using a felt pen mark the mounting hole locations.
2. Mounting the ampliļ¬er on carpet will signiļ¬cantly reduce air ļ¬ow, resulting in reduced thermal run times.
3. Mount the ampliļ¬er on a solid surface. Avoid mounting to sub woofer enclosures or areas prone to vibration. Do not install
the ampliļ¬er on plastic or other combustible materials.
4. Prior to mounting the ampliļ¬er, make sure not to cut or drill into the fuel tank, fuel lines, brake lines (under chassis) or
electrical wiring.
WIRING PRECAUTIONS
1. Before installation, make sure the source unit power switch is in the OFF position.
2. Disconnect the negative (-) lead of the battery before making any power connections.
3. When making connections, be sure that each one is clean and secure. Insulate all of your connections. Failure to do so
may damage your equipment.
4. A secure clean ground connection is critical to the performance of your ampliļ¬er. Connect the ground directly to the car
chassis to minimize resistance and avoid any noise problems.
5. Add an external fuse on the ampliļ¬erās positive (+) power lead and connect it as close as possible to the vehicleās (+)
battery terminal. Use a rating that equals the total current consumption at full output of all ampliļ¬ers in the system. This
external fuse will protect the vehicle from short circuits that can cause a ļ¬re.
Product specificaties
| Merk: | Diamond Audio |
| Categorie: | Receiver |
| Model: | HXM1200.1D |
Heb je hulp nodig?
Als je hulp nodig hebt met Diamond Audio HXM1200.1D stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Receiver Diamond Audio
23 Mei 2025
23 Mei 2025
23 Mei 2025
23 Mei 2025
23 Mei 2025
23 Mei 2025
23 Mei 2025
22 Mei 2025
22 Mei 2025
22 Mei 2025
Handleiding Receiver
- Receiver Ibanez
- Receiver Panasonic
- Receiver Peavey
- Receiver Hirschmann
- Receiver Orava
- Receiver Mosconi
- Receiver Rolls
- Receiver Tangent
- Receiver Sandberg
- Receiver Kathrein
- Receiver Genie
- Receiver Redline
- Receiver Graupner
- Receiver Bugera
- Receiver Viscount
Nieuwste handleidingen voor Receiver
4 Juni 2025
4 Juni 2025
4 Juni 2025
4 Juni 2025
4 Juni 2025
4 Juni 2025
4 Juni 2025
4 Juni 2025
4 Juni 2025
4 Juni 2025