CyberPower UT650E Handleiding

Bekijk gratis de handleiding van CyberPower UT650E (2 pagina’s), behorend tot de categorie UPS. Deze gids werd als nuttig beoordeeld door 60 mensen en kreeg gemiddeld 4.2 sterren uit 6 reviews. Heb je een vraag over CyberPower UT650E of wil je andere gebruikers van dit product iets vragen? Stel een vraag

UT650E User’s Manual K01-C000347-00

IMPORTANT SAFETY INSTRUCTIONS

This manual contains important safety instructions. Please read and follow all instructions carefully during installation and operation of the unit. Read this

manual thoroughly before attempting to unpack, install, or operate your UPS.

CAUTION!To prevent the risk of fire or electric shock, install in a temperature and humidity controlled indoor area free of conductive contaminants. (See the

specifications for the acceptable temperature and humidity range.)

CAUTION!To reduce the risk of overheating the UPS, do not cover the UPS' cooling vents and avoid exposing the unit to direct sunlight or installing the unit

near heat emitting appliances such as space heaters or furnaces.

CAUTION! Do not attach non-computer-related items, such as medical equipment, life-support equipment, microwave ovens, or vacuum cleaners to UPS.

CAUTION! Do not allow liquids or any foreign object to enter the UPS. Do not place beverages or any other liquid-containing vessels on or near the unit.

CAUTION! In the event of an emergency, press the OFF button and disconnect the power cord from the AC power supply to properly disable the UPS.

CAUTION! Unplug the UPS prior to cleaning and do not use liquid or spray detergent.

CAUTION! Servicing of batteries should be performed or supervised by personnel knowledgeable of batteries and the required precautions. Keep

unauthorized personnel away from batteries.

UNPACKING

The box should contain the following: (1) UPS Unit x1; (2) User Manual x1; (3) USB Cable x1

HARDWARE INSTALLATION GUIDE

1. Your new UPS may be used immediately upon receipt. However, recharging the battery for at least 8 hours is recommended to ensure that the battery's

maximum charge capacity is achieved. Charge loss may occur during shipping and storage. To recharge the battery, simply leave the unit plugged into

an AC outlet. The unit will charge in both the on and off position.

2. With the UPS unit off and unplugged, connect the computer, monitor, and any externally powered data storage device (Zip drive, Jazz drive, Tape drive,

etc. into the battery power supplied outlets. DO NOT plug a laser printer, copier, space heater, vacuum, paper shredder or other large electrical device

into the battery power supplied outlets. The power demands of these devices will overload and possibly damage the unit.

3. Plug the UPS into a 2 pole, 3 wire grounded receptacle (wall outlet). Make sure the wall branch outlet is protected by a fuse or circuit breaker and does

not service equipment with large electrical demands (e.g. air conditioner, refrigerator, copier, etc. Avoid using extension cords.

4. Press the power switch to turn the unit on. The power on indicator light will illuminate and the unit will "beep".

5. If an overload is detected, an audible alarm will sound and the unit will emit one long beep. To correct this, turn the UPS off and unplug at least one piece

of equipment from the battery power supplied outlets. Wait 10 seconds. Make sure the circuit breaker / fuse is normal and then turns the UPS on.

6. To maintain optimal battery charge, leave the UPS plugged into an AC outlet at all times.

7. To store your UPS for an extended period, cover it and store with the battery fully charged. Recharge the battery every three months to ensure battery

life.

1. Power Switch

Press the switch for 2 seconds to turn the UPS ON or OFF.

Alarm setting: The audible alarm can be turned OFF or ON by quickly pressing the POWER button twice. The default setting is for the Alarm

On. To turn the Alarm Off, quickly press the power button twice. You will hear two short beeps

when the Alarm is turned off. To turn the Alarm back on, quickly press the power button twice.

You will hear a single short beep when the Alarm is turned on.

2. Led Indicators This LED is illuminated when the UPS is working.

3. Input Power Cord Connect to utility power.

4. AC outlet

The UPS provides outlets for connected equipment to insure temporary uninterrupted

operation during a power failure and against surges and spikes.

5. USB Port

This port allows connection and communication from the USB port on the computer to the

UPS unit. The UPS communicates its status to the PowerPanel® Personal Edition software.

DEFINITIONS FOR ILLUMINATED LED INDICATORS

LED Alarm Condition

On Off Normal

Flash Beep Twice Utility Failure - The UPS is providing battery power to outlets.

Flash Rapid Beeping Utility Failure - The UPS is providing battery power. The rapid beeps indicate the battery will run out of power shortly.

On/Flash Constant Tone

Overload - Occurs when connected equipment exceeds the rating of the unit. Turn the UPS off and unplug at least one

piece of equipment from the UPS.

BASIC OPERATION

INSTALLING YOUR UPS SYSTEM

Product specificaties