CRUX SWRSU-38B Handleiding


Lees hieronder de πŸ“– handleiding in het Nederlandse voor CRUX SWRSU-38B (3 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 18 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/3
Crux Interfacing Solutions β€’ 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
phone: (818) 609-9299 β€’ fax: (818) 996-8188 β€’ www.cruxinterfacing.com
rev.022120
SWRSU-38B
Radio Replacement with Steering Wheel Control Retention for
Select SUBARU Vehicles 2008 - 2015
1 of 3
RADI O REPLAC EMEN T
SWC R ETENT IO N
+
R
INTERFACING SOLUTIONS
- Retains factory features in select Subaru vehicles while funconing with an aermarket radio.
- Pre-programmed to retain factory Steering Wheel Controls.
PRODUCT FEATURES:
PARTS INCLUDED:
SWRSU-38B Module SU-38B Harness SWC Cable
INSTALLATION DIAGRAM:
AFTERMARKET
RADIO
4-Pin
Connector
Cap or insulate if
not being used
Kenwood/JVC (BLUE / YELLOW)
Insulate with tape
if not being used
3.5MM SWC CABLE
Plug in the 3.5MM SWC cable to the 4-pin port
on the module. See β€œDIP SWITCH SETTINGS” section.
ON RADIO VEHICLE
1 2 3 4 5 6 7 8
+12V Constant Yellow
+12V ACC Red
Ground Black
ξ˜―ξ―ξ―ξž΅ξ΅ξξΆξœ‚ξžŸξ½ξΆξ˜ƒξ₯Ύξ¨½ξ₯Ώξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ™‹ξžŒξœ‚ξΆξξœž
Antenna Power Blue
ξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜˜ξξ΅ξ΅ξœžξžŒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ™‹ξžŒξœ‚ξΆξξœžξ₯¬ξ™΄ξšξξžšξœž
ξ™šξξξšξžšξ˜ƒξ˜¦ξžŒξ½ξΆξžšξ˜ƒξ₯Ύξ¨½ξ₯Ώξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜§ξžŒξœ‚ξŸ‡
ξ™šξξξšξžšξ˜ƒξ˜¦ξžŒξ½ξΆξžšξ˜ƒξ₯Ύξ₯²ξ₯Ώξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜§ξžŒξœ‚ξŸ‡ξ₯¬ξ˜‘ξ―ξœ‚ξœξ¬
ξ˜ΎξœžξŒξ˜ƒξ˜¦ξžŒξ½ξΆξžšξ˜ƒξ₯Ύξ¨½ξ₯Ώξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ™΄ξšξξžšξœž
ξ˜ΎξœžξŒξ˜ƒξ˜¦ξžŒξ½ξΆξžšξ˜ƒξ₯Ύξ₯²ξ₯Ώξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ™΄ξšξξžšξœžξ₯¬ξ˜‘ξ―ξœ‚ξœξ¬
ξ™šξξξšξžšξ˜ƒξ™šξœžξœ‚ξžŒξ˜ƒξ₯Ύξ¨½ξ₯Ώξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ™³ξξ½ξ―
ξ™šξξξšξžšξ˜ƒξ™šξœžξœ‚ξžŒξ˜ƒξ₯Ύξ₯²ξ₯Ώξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ™³ξξ½ξ―ξ₯¬ξ˜‘ξ―ξœ‚ξœξ¬
ξ˜ΎξœžξŒξ˜ƒξ™šξœžξœ‚ξžŒξ˜ƒξ₯Ύξ¨½ξ₯Ώξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜§ξžŒξœžξœžξΆ
ξ˜ΎξœžξŒξ˜ƒξ™šξœžξœ‚ξžŒξ˜ƒξ₯Ύξ₯²ξ₯Ώξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜ƒξ˜§ξžŒξœžξœžξΆξ₯¬ξ˜‘ξ―ξœ‚ξœξ¬
TO FACTORY
HARNESS
12-Pin Black
Connector
Ground
AFTERMARKET
RADIO SELECTOR
(See Page 2)
SUBARU
SWC SETTING
(See Page 2)
ON RADIO VEHICLE
1 2 3 4 5 6 7 8
To aftermarket
radio SWC wire or
3.5mm port
GREEN
BROWN BROWN
Connect BROWN to BROWN wire.
***See special note on 2010 & 2011 Forester, Legacy and Outback connection on page 2***
Crux Interfacing Solutions β€’ 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
phone: (818) 609-9299 β€’ fax: (818) 996-8188 β€’ www.cruxinterfacing.com
rev.022120
SWRSU-38B
Radio Replacement with Steering Wheel Control Retention for
Select SUBARU Vehicles 2008 - 2015
2 of 3
RADI O REPLAC EMEN T
SWC R ETENT IO N
+
R
INTERFACING SOLUTIONS
DIP SWITCH SETTINGS:
SUBARU STEERING WHEEL CONTROL DIP SWITCH SETTING:
NOTE: Insulate the Blue/Yellow wire or 3.5mm plug if not being used.
AFTERMARKET RADIO DIP SWITCH SETTINGS:
RADIO BRAND: DIP: 1 2 3 4
Atoto, Dual, Farenheit, Jensen, Pioneer
Power Acoustik, Soundstream
Blaupunkt, Most o-brand Radios
Alpine
Clarion
Kenwood
JVC
Boss, Old Sony
New Sony
OFF OFF ON ON
OFF OFF ON ON
OFF OFF ON ON
OFF OFF OFF OFF
OFF ON ON OFF
OFF ON ON ON
OFF ON OFF ON
OFF ON OFF OFF
OFF OFF ON OFF
SWC MODULE
ON RADIO VEHICLE
1 2 3 4 5 6 7 8
NOTE: For Atoto, Blaupunkt, Dual, Farenheit, Power Acoustik, Soundstream, and most o-brand radios,
check the aftermarket radio’s manual to see if the SWC buttons need to be programmed.
3.5MM SWC CABLE
Plug in the 3.5MM to 4-Pin SWC cable to the SWC module.
DIP: 5 6 7 8
Panasonic made Radio
Clarion made Radio*
Clarion made Radio**
Fujitsu Ten made Radio
ON OFF OFF ON
OFF ON OFF ON
ON OFF ON OFF
OFF ON OFF ON
SWC MODULE
ON RADIO VEHICLE
1 2 3 4 5 6 7 8
Original radio manufacturer informaon can be found on the label on top of the radio.
STEERING WHEEL CONTROL DIP SWITCHES ARE TO BE SET IN ACCORDANCE WITH THE ORIGINALLY REMOVED FACTORY RADIO:
*For steering wheels with pickup and hangup phone buons.
**For steering wheels without pickup and hang up phone buons.
For the year model Subaru vehicles listed above, check the factory radio harness if it has a GREEN/YELLOW wire across the
BROWN wire on the SWRSU-38B harness (see diagram A). If it has a GREEN/YELLOW wire follow the connecon chart below
and refer to diagram B. Set DIP switches 5 to 8 to: . ON OFF ON OFF
SPECIAL NOTE ON 2010 & 2011 FORESTER, LEGACY and OUTBACK:
BROWN
BLACK
BLACK
SWRSU-38B Harness
GREEN/YELLOW
ORANGE/WHITE
Factory Harness
BLACK
diagram A
WITHOUT Phone buons on steering wheel disconnect BROWN wire
WITH Phone buons on steering wheel disconnect BROWN wire and connect to GREEN wire
GREEN
BROWN
BROWN
diagram B
SU-38B Harness
Crux Interfacing Solutions β€’ 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
phone: (818) 609-9299 β€’ fax: (818) 996-8188 β€’ www.cruxinterfacing.com
rev.022120
SWRSU-38B
Radio Replacement with Steering Wheel Control Retention for
Select SUBARU Vehicles 2008 - 2015
3 of 3
RADI O REPLAC EMEN T
SWC R ETENT IO N
+
R
INTERFACING SOLUTIONS
VEHICLE APPLICATIONS:
SUBARU
2009-2015
2008-2014
2010-2014
2010-2014
2013-2014
Forester*
Impreza (WRX)
Legacy
Outback*
XV Crosstrek
Subaru Outback Radio
INSTALLATION INSTRUCTIONS:
1. We recommend pung tape
around the radio bezel to protect the
dashboard from being scratched.
2. Use a plasc pry bar and carefully li
the radio bezel going all the way around
it. Having a second pry bar would help.
3. Once you have lied the radio bezel,
carefully pull it out. Again, slowly going
all the way around it using your hands.
4. There are 4 screws holding the radio. 5. Pull out the radios and unplug the
connectors.
6. Plug in the SWRSU-38B T-harness
to the vehicle harness and hide the
module in the radio cavity.
7. Use the necessary dash kit (not included) to complete the installaon. Connect the aermarket radio wires to the
SWRSU-38B T-harness.
8. Test the radio for funconality before installing the new radio into the dash. Carefully reinstall the radio bezel.
*See special note on 2010 and 2011 Forester and Outback on page 2.


Product specificaties

Merk: CRUX
Categorie: Niet gecategoriseerd
Model: SWRSU-38B

Heb je hulp nodig?

Als je hulp nodig hebt met CRUX SWRSU-38B stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd CRUX

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd