Chef's Choice ScissorPro 500 Handleiding
Chef's Choice
Messenslijper
ScissorPro 500
Lees hieronder de 📖 handleiding in het Nederlandse voor Chef's Choice ScissorPro 500 (8 pagina's) in de categorie Messenslijper. Deze handleiding was nuttig voor 13 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/8
MODEL 500 InstructIOns
ScissorPro®
Diamond Hone® Sharpener
Read these instructions before use.
It is essential that you follow these
instructions to achieve optimum results.
© 2012 EdgeCraft Corp.
Important SafeguardS
When using electrical appliances, basic safety precautions should always be
followed including the following:
1. Read all instructions.
2. To protect against electrical hazards, do not immerse the ScissorPro
® in water or
other liquid.
3. Make sure only clean scissor blades are inserted in the ScissorPro
®.
4. Unplug from outlet when not in use, before putting on or taking off parts and
before cleaning.
5. Avoid contacting moving parts.
6. Do not operate any appliance with a damaged cord or plug, or after the appliance
malfunctions, or is dropped or damaged in any manner.
U.S. customers: You may return your sharpener to EdgeCraft’s factory for service where
the cost of repair or electrical or mechanical adjustment can be estimated. If the
electrical cord on this appliance is damaged, it must be replaced by the Chef’sChoice
distributor or other qualified service to avoid the danger of electrical shock.
Outside U.S.: Please return your sharpener to your local distributor where the cost of
repair or electrical or mechanical adjustment can be estimated. If the supply cord
of this appliance is damaged, it must be replaced by a repair facility appointed by
the manufacturer because special tools are required. Please consult your
Chef’sChoice distributor.
7. CAUTION! This appliance may be fitted with a polarized plug (one blade is wider than
the other). To reduce the risk of electric shock, this plug will fit in a polarized outlet only
one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician. Do not modify the plug in anyway.
8. The use of attachments not recommended or sold by EdgeCraft Corporation may cause
fire, electric shock or injury.
9. The ScissorPro® Model 500 is designed to sharpen kitchen, household, sewing and arts
and crafts scissors. Do not attempt to sharpen pinking shears, serrated blades or knives.
Do not attempt to sharpen any scissor blades that does not fit freely in the slots.
10. Do not let the cord hang over edge of table or counter, or touch hot surfaces.
11. When in the “ON” position the ScissorPro
® should always be on a level, stable
countertop or table.
12. WARNING: SCISSORS PROPERLY SHARPENED ON YOUR ScissorPro
® WILL BE SHARPER
THAN YOU EXPECT. TO AVOID INJURY, USE AND HANDLE THEM WITH EXTREME CARE.
DO NOT CUT TOWARD ANY PART OF YOUR FINGERS, HAND OR BODY. DO NOT RUN
FINGER ALONG EDGE. STORE IN A SAFE MANNER.
13. Do not use outdoors.
14. Close supervision is necessary when any appliance is used by or near children.
15. Do not use honing oils, water or any other lubricant with the ScissorPro
®.
16. For household use only.
17. SAVE THESE INSTRUCTIONS.
2
CongratulatIonS
You are the owner of the world’s finest scissors sharpener designed to permit everyone to sharpen
scissors to professional standards, simply and easily. The ScissorPro
® will put an incredibly sharp
edge on your kitchen, household, sewing and arts and crafts scissors. It is important to completely
read this booklet to optimize your sharpening results.
ScissorPro® owes much of its uniqueness to its precision magnetic guides, designed to hold the
scissors blade securely at a precise angle against the specially contoured, Omni-Curve
™ rotating
diamond abrasive disks. These guides (see Figures 1 and 2) incorporate a unique hold-down spring
mechanism and, in combination with the magnets, comprise the unique Magne-Flex
™ scissors hold-
down system. Before sharpening your first scissors it is important to read the following section:
3
Figure 2. Magnets control the blade angle
and keep scissors in contact with diamond
abrasive disk.
Omni-Curve ™
Diamond Disk
Magnet
Figure 3. Typical scissors.
Cutter
Edge
Anvil Edge
Back of Blade Tip
Pivot
Top of Blade
Figure 1. ScissorPro® Model 500.
Plastic Hold-Down Spring
Plastic Hold-Down Spring
On/Off Switch
“Fine” Stage
Diamond Abrasives
“Coarse” Stage
Diamond Abrasives
Magnet Surface Magnet
Surface
Magne-Flex™ Guides
Product specificaties
| Merk: | Chef's Choice |
| Categorie: | Messenslijper |
| Model: | ScissorPro 500 |
Heb je hulp nodig?
Als je hulp nodig hebt met Chef's Choice ScissorPro 500 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Messenslijper Chef's Choice
8 Januari 2024
8 Januari 2024
28 Oktober 2023
28 Oktober 2023
28 Oktober 2023
28 Oktober 2023
28 Oktober 2023
28 Oktober 2023
28 Oktober 2023
28 Oktober 2023
Handleiding Messenslijper
- Messenslijper IKEA
- Messenslijper Krups
- Messenslijper Adler
- Messenslijper Bartscher
- Messenslijper Beper
- Messenslijper Berkel
- Messenslijper Bifinett
- Messenslijper Blokker
- Messenslijper Bomann
- Messenslijper Domo
- Messenslijper EdgeCraft
- Messenslijper Fagor
- Messenslijper Gardenline
- Messenslijper Gastroback
- Messenslijper Gourmetmaxx
- Messenslijper Graef
- Messenslijper Gude
- Messenslijper Melissa
- Messenslijper Powerplus
- Messenslijper Presto
- Messenslijper Princess
- Messenslijper Roadstar
- Messenslijper Salter
- Messenslijper Silvercrest
- Messenslijper Sogo
- Messenslijper Steba
- Messenslijper Studio
- Messenslijper Tower
- Messenslijper Trebs
- Messenslijper Ozito
- Messenslijper Clatronic
- Messenslijper Guzzanti
- Messenslijper OBH Nordica
- Messenslijper Orbegozo
- Messenslijper Tacklife
- Messenslijper Waring Commercial
- Messenslijper Brentwood
- Messenslijper Genie
- Messenslijper C3
- Messenslijper Orava
- Messenslijper For_Q
- Messenslijper Wüsthof
- Messenslijper Work Sharp
- Messenslijper Petra Electric
- Messenslijper GARDE
- Messenslijper IdeenWelt
- Messenslijper Donau Elektronik
Nieuwste handleidingen voor Messenslijper
8 April 2024
8 April 2024
8 April 2024
19 Maart 2024
16 Maart 2024
16 Maart 2024
16 Maart 2024
6 Maart 2024
6 Maart 2024
28 Februari 2024