Chapin 26127 Handleiding

Bekijk gratis de handleiding van Chapin 26127 (2 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 27 mensen en kreeg gemiddeld 4.0 sterren uit 9 reviews. Heb je een vraag over Chapin 26127 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

6-4625

Shut-off Hand

Mango de cierr

Poignée du rob

Parts, P

6-6093

Hose

Manguera

Tuyau

Check

5. Filling

1) Turn pump handle counterclockwise and remove pumpDo:

2) Do: Prepare spray solution following all directions and safety warnings on chemical label.

3) Do: Fill tank to no more than the proper gallon marker. Do NOT: overfill to accommodate pump.

4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and

tighten securely.

8. Care, Storage and Maintenance

018343R0222

1. Hose to Tank

Make sure white outlet

tube is attached to

hose.

Insert tube into

tank.

Proper placement of

white outlet tube.

Line up tabs on

safety lock connec-

tor with notches on

the outlet flange of

the tank. Insert tabs

into notches to form

a secure seal.

Slip hose nut

down to tank, turn

clockwise and

tighten as tight as

possible by hand.

1A

1B

1C

1D1E

9. Fatigue-Free Spraying

prevent clogging while spraying. It is

nd of the outlet tube inside your sprayer

ter, remove the discharge assembly from

3A). Make sure the filter is positioned at

e tank as pictured.

Filter

3A

6-7750

Extension wa

2. Nozzle

shut-off handle or extension wand.

For constant spraying, push down on shut-off handle

and move grey locking mechanism away from you. To

release, squeeze handle and move the grey locking

mechanism back towards you. ( Not all models are

provided with this feature).

9A

Locking

mechanism

ghtness of hose nut to be sure hose is securely attached to the tank outlet.

hose for deterioration, cracks, softness, or brittleness. If any of these conditions

place hose before using. Replace with original manufacturer’s parts only.

pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and

nk for signs of deterioration of body and bottom. Any sign of deterioration

ssible tank weakening and could result in explosive bursting under pressure.

se signs are found, discard tank immediately and replace. Do not attempt to patch

s this could result in serious injury.

lling, Pressurizing and Spraying Instructions, except use water only (Pump plunger

s and inspect for leaks).

ut-off away from you and open to make sure discharge is not clogged.

sses this test, release pressure (see Pressure Releasing Instructions), empty tank,

with Filling, Pressurizing and Spraying Instructions.

all metal parts including the wand, nozzle and fittings for rust, corrosion and pitting.

se conditions are found, replace affected part with original manufacturer’s part

.

1) Follow chemical manufacture’s instructions for cleaning. Rinse thoroughly with Do:

recommended solvent. Follow Filling, Pressurizing and Spraying Instructions, except pump

unit only 8-10 strokes. Be sure that the wand and nozzle are thoroughly rinsed after each use.

2) Do: Open shut-off and allow recommended solvent to run through discharge assembly.

3) Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer. Do:

4) Store sprayer tank upside down, with pump removed, in a warm dry location. Do:

5) Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening Do:

in cover.

7. To Release Pressure

1) With pump facing away, turn locked handle counterclockwise until air begins to escape. Do:

Stop turning handle when you hear air escaping.

2) Do: Stay away from the sprayer until all air has escaped.

Pull handle

straight up.

Insert notches

from underside

of handle

into plunger

grooves and turn

counterclockwise.

Remove plunger. Wash

diaphragm in mild dish

detergent.

Tighten plunger clockwise

until flush to top of shut-

off body. Do not over-

tighten or unit may not

spray. Slide forks under

plunger, push handle

down until it snaps into

place.

10. Troubleshooting

-

Tank pressurizes but does not spray.

10A10B10C

Handle

Plunger

Body

Rubber

Diaphragm

10D

Plunger flush

with body

WARNING:

Release pressure in tank before troubleshooting.

Clean shut-off (Fig. 10A- 10D)

WARNING: Improper use or failure to follow instructions can result in explosive failure causing serious

eye or other injury.For safe use of this product you must read and follow all instructions. Do not leave a

pressurized sprayer in the hot sun. Heat can cause pressure build-up resulting in possible explosion. Do not

store or leave solution in tank after use. Always wear goggles, gloves, long sleeve shirt, long pants and full foot

protection when spraying. Never use any tool to remove pump if there is pressure in sprayer. Never stand with

face or body over top of tank when pumping or loosening pump to prevent ejecting pump assembly and/or

solution from striking and injuring you. Never pressurize sprayer by any means other than the original pump.

Do not attempt to modify this sprayer. Replace parts only with manufacturer’s original parts. This sprayer is

intended for Acetone only. Acetone is extremely flammable. This Acetone sprayer is intended for trained

professionals only- Not intended for the retail trade. Always read and follow chemical manufacturer’s

instructions before use with this sprayer as some chemicals may be hazardous when used with this sprayer.

Sk-1169-1

6. Pressurizing and Spraying

Do: Turn handle clockwise

to tighten. Push handle

down, turn 1/4 turn

counterclockwise to

release.

Do: Pump until you

feel resistance.

Do: Push handle, down,

turn 1/4 turn clockwise to

lock. Begin spraying. Re-

pump sprayer as required

to maintain spray force.

6A6B6C

2B

WARNING

Note:Your particular

pictured above.

Nota: Es posible que

incluya todas las par

Remarque :Votre pu

pas inclure toutes les

Congratulations!

You have just purchased a quality Chapin product.

Register Your Sprayer Online @ www.chapinmfg.com Questions? Do Not Return To Store.

Call us @ 1-800-950-4458 or www.chapinmfg.com

6-1927

Repair Parts Kit Gask

Juego de piezas de r

Kit de pièces de répa

P.O. Box 549 700 Ellicott St.

Batavia, NY 14021-0549 U.S.A.1-800-950-4458 www.chapinmfg.com

Product specificaties