Brondell VivaSpring FSH-25 Handleiding

Bekijk gratis de handleiding van Brondell VivaSpring FSH-25 (1 pagina’s), behorend tot de categorie Digitális fényképezőgép. Deze gids werd als nuttig beoordeeld door 3 mensen en kreeg gemiddeld 4.6 sterren uit 7 reviews. Heb je een vraag over Brondell VivaSpring FSH-25 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Questions about installation? Call our customer service department at 888-542-3355 or visit brondell.com

Installation

1. Remove the existing Shower Head from the shower arm (pipe) by

turning it counterclockwise.

2. Clean away any debris that may be on the threaded portion of the

shower arm. Wrap the included plumber’s tape tightly around the

shower arm threads 2 or 3 times to prevent leaking.

3. Unscrew the two halves of the Shower Head.

4. Peel the stickers o of the Filter Cartridge and place the Filter

Cartridge in the Filter Housing. The Filter Cartridge can be installed

with either side up. Close the Shower Head by screwing the two

halves of the Shower Head back together tightly.

5. Unscrew the protective cap from the Inlet Collar and ensure that the

rubber washer with mesh screen is in place inside of the Inlet Collar.

Hold the Shower Head up to the shower pipe and turn the Shower

Head by hand clockwise, until tight. Use an adjustable wrench to

tighten the connection, if needed, to help alleviate leaking.

6. Turn water on and check for leaks. Tighten the connection as

necessary. Flush the Filter Cartridge by running the shower for

2 minutes, or until the water runs clear.

Filter replacement

To ensure maximum eectiveness, replace the Filter Cartridge every

10,000 gallons, or six months of use, with the Brondell FF-15

Replacement Filter Cartridge.

1. Open the Shower Head: Rubber gloves are recommended to help get

a better grip on the housing. With one hand, grasp the back half of the

Shower Head tightly. Using your other hand, turn the front half of the

Shower Head counter-clockwise until the two halves are separated.

2. Remove the used Filter Cartridge by pulling it out from the Filter

Housing in the back half of the Shower Head.

3. Peel the stickers o of the new Filter Cartridge. Place the new Filter

Cartridge into the housing – the Cartridge can be installed either

side up.

4. Close the Shower Head by screwing the two halves back together

tightly.

5. Turn water on and check for leaks. Tighten the connection as

necessary. Flush the Filter Cartridge by running the shower for 2

minutes, or until the water runs clear.

Before You Begin

When changing the Filter Cartridge, or installing the VivaSpring filtered

shower head for the first time, rubber gloves are recommended to help

get a better grip on the housing.

While installing or re-installing the VivaSpring filtered shower head, we

recommended wrapping a rag or small towel around the Inlet Collar

before you tighten with a wrench to avoid scratching the finish.

VivaSpring FSH25 Series Filtered Shower Head Installation

CAUTION:Risk of Personal Injury! If the water temperature is

set too high, scalding will occur. The water temperature should

never be set above 120°F (49°C). Do not use this Brondell low-flow

product with a shower valve that allows the water temperature to

become too hot.

NOTE:Do not over-tighten the Inlet Collar. Over-tightening may

cause the rubber washer to compress into the shower arm, which

can cause leaking. If this occurs, uninstall the Shower Head,

reinstall the washer, and reconnect the Shower Head.

Parts Included

• Shower Head

• Filter Cartridge

• Plumber’s Tape

Tools Needed

• Adjustable Wrench

• Rag or Small Towel

• Rubber Gloves

(optional for better grip)

Product specificaties