Boss VB-2W Handleiding

Boss Niet gecategoriseerd VB-2W

Lees hieronder de 📖 handleiding in het Nederlandse voor Boss VB-2W (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 19 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1

Owner’s Manual

OUTPUT jack

Connect this jack to your amp or to the

input of another eect unit.

Guitar Amplier

DEPTH jack

If an expression pedal is connected, you can use the pedal

to control the depth of modulation.

* Refer to “Caution When Using the DEPTH Jack.”

Precautions When Connecting

5 To prevent malfunction and equipment failure, always turn

down the volume, and turn o all the units before making any

connections.

5 Once the connections have been completed, turn on power to

your various devices in the order specied. By turning on devices

in the wrong order, you risk causing malfunction and/or damage

to speakers and other devices.

When powering up: Turn on the power to your guitar amp last.

When powering down: Turn o the power to your guitar amp rst.

5 Due to the characteristics of its analog circuitry, this unit’s CHECK

indicator may be lit (eect on) or unlit (eect o) when you turn

the power on.

Use of Battery

5 A battery was installed in the unit before it left the factory. The life

of this battery may be limited, however, since its primary purpose

was to enable testing.

5 If you handle batteries improperly, you risk explosion and uid

leakage. Make sure that you carefully observe all of the items

related to batteries that are listed in “USING THE UNIT SAFELY” and

“IMPORTANT NOTES” (supplied on a separate sheet).

5 When operating on battery power only, the unit’s indicator will

become dim when battery power gets too low. Replace the

battery as soon as possible.

5 Batteries should always be installed or replaced before connecting

any other devices. This way, you can prevent malfunction and

damage.

Changing the Battery

1. Hold down the pedal and loosen the thumbscrew, then

open the pedal upward.

* The pedal can be opened without detaching the thumbscrew

completely.

Thumbscrew

Battery Housing

Pedal

Spring Base

Coil Spring

Guide Bush

Hole

Battery Snap

Cord

Battery

Snap

9 V Battery

2. Remove the old battery from the battery housing, and

remove the snap cord connected to it.

3. Connect the snap cord to the new battery, and place

the battery inside the battery housing.

* Be sure to carefully observe the battery’s polarity (+ versus -).

4. Slip the coil spring onto the spring base on the back of

the pedal, and then close the pedal.

* Carefully avoid getting the snap cord caught in the pedal, coil

spring, and battery housing.

5. Finally, insert the thumbscrew into the guide bush

hole and fasten it securely.

Caution When Using the DEPTH Jack

5 Use only the specied expression pedal (BOSS FV-500H, FV-500L,

Roland EV-5; sold separately). By connecting any other expression

pedals, you risk causing malfunction and/or damage to the unit.

5 You can use the DEPTH knob to adjust the amount of modulation

that occurs when the pedal is in the maximum position.

5 You can use the minimum volume control of the EV-5 to adjust

the amount of modulation that occurs when the pedal is in the

minimum position.

Specications

Nominal Input Level -20 dBu

Input Impedance 1 MΩ

Nominal Output

Level -20 dBu

Output Impedance 1 kΩ

Recommended Load

Impedance 10 kΩ or greater

Power Supply Alkaline battery (9 V, 6LR61) (9 V, 6F22) or

Carbon-zinc battery

AC adaptor (PSA series: sold separately)

Current Draw 35 mA

* Expected battery life under continuous use:

Alkaline: 22 hours

Carbon: 4 hours

These gures will vary depending on the

actual conditions of use.

Dimensions 73 (W) x 129 (D) x 59 (H) mm

2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches

Weight 450 g / 1lb 1 oz (including battery)

Accessories Leaet (“USING THE UNIT SAFELY,” “IMPORTANT

NOTES,” and “Information”)

Alkaline battery (9 V, 6LR61)

Options

(sold separately)

AC adaptor (PSA-series)

Expression pedal (BOSS FV-500H, FV-500L,

Roland EV-5)

* 0 dBu = 0.775 Vrms

* This document explains the specications of the product at the

time that the document was issued. For the latest information,

refer to the Roland website.

Thumbscrew

When this screw is loosened, the

pedal will open, allowing you to

change the battery.

* For instructions on changing

the battery, refer to “Changing

the Battery.”

AC Adaptor

(PSA series: optional)

Electric Guitar

English

7This is a “WAZA CRAFT series” eect unit featuring analog circuitry painstakingly designed in every detail for the best possible sound.

7It is a vibrato unit featuring a unique eect that uses a carefully selected BBD.

7In addition to the sound of the original VB-2, you’ll enjoy a custom tone that’s been fully tuned-up by BOSS engineers.

Main Features

INPUT jack

This jack accepts signals coming from

a guitar or other musical instrument, or

another eects unit.

* The INPUT jack doubles as the power switch.

Power to the unit is turned on when you plug into the

INPUT jack; the power is turned o when the cable is

unplugged.

To prevent unnecessary battery consumption, be sure

to disconnect the plug from the INPUT jack when not

using the eects unit.

Panel Descriptions

DC IN jack

Accepts connection of an AC Adaptor (PSA series; optional). By using an AC Adaptor, you can play without

being concerned about how much battery power you have left.

* Use only the specied AC adaptor (PSA series; optional), and connect it to an AC outlet of the correct

voltage. Do not use any other AC adaptor, since this may cause malfunction.

* If the AC adaptor is connected while a battery is installed, the power supply is

drawn from the AC adaptor.

* We recommend that you keep batteries installed in the unit even though

you’ll be powering it with the AC adaptor. That way, you’ll be able to

continue a performance even if the cord of the AC adaptor gets accidently

disconnected from the unit.

CHECK indicator

This indicator shows whether the eect is on or o, and also doubles as the battery check

indicator. The indicator lights when the eect is on.

* If you’re powering the unit with a battery and the CHECK indicator goes dim— or doesn’t

light at all—when you try to turn the eect on, the battery is near depletion and should be

replaced. For instructions on changing the battery, refer to “Changing the Battery.”

Pedal switch

This switch turns the eect on/o.

RATE knob

RISE TIME knob

DEPTH knob

Standard/Custom switch

MODE knob

Adjusts the modulation speed of the vibrato eect.

Adjusts the time until the maximum vibrato eect is reached.

Adjusts the modulation depth of the vibrato eect.

Switches the function of the pedal.

UNLATCH The vibrato eect is on only while you hold down the pedal.

BYPASS

The vibrato eect turns on/o each time you press the pedal.

Turning the vibrato eect o bypasses the BBD so that the audio

signal does not pass through it.

LATCH The vibrato eect turns on/o each time you press the pedal.

* When the vibrato eect is turned o in UNLATCH or LATCH mode, the

audio signal passes through the BBD so that the eect can begin smoothly.

Switches the tonal character.

Cable:

Stereo 1/4” phone type

Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet).

After reading, keep the document(s) where it will be available for immediate reference.

S (standard) The original tone of the VB-2.

C (custom) A custom tone with emphasized modulation, in which the

frequency response also changes.

Product specificaties

Merk:	Boss
Categorie:	Niet gecategoriseerd
Model:	VB-2W
Kleur van het product:	Blauw
Gewicht:	450 g
Breedte:	73 mm
Diepte:	129 mm
Hoogte:	59 mm
Type stroombron:	AC, Battery
Accu/Batterij voltage:	9 V
Ondersteund aantal accu's/batterijen:	1
Aansluiting voor netstroomadapter:	Ja
Stroomverbruik:	35 mA
Beste gebruik:	Gitaar
Type product:	Expressiepedaal
Synchronisatie ingangsimpedantie:	1000000 Ohm
Uitgang van 6,35 mm (1/4-inch):	1
Output impedance:	1000 Ohm
Ingang van 6,35 mm (1/4-inch):	2
Uitgangsniveau:	-20/0 dB
Garantieperiode:	5 jaar
Nominale input level:	-20 dB
Status-indicatorlichtje:	Ja