Boss SDE-3000D Handleiding

Boss Niet gecategoriseerd SDE-3000D

Lees hieronder de 📖 handleiding in het Nederlandse voor Boss SDE-3000D (41 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 101 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/41

Reference Manual

Connecting the Equipment

* To prevent malfunction and equipment failure, always turn

down the volume, and turn o all the units before making any

connections.

CTL 4, 5 jacks only (for the GA-FC)

INPUT

CTL 2, 3

EXP 1

OUTPUT ROUTPUT L

CTL 4, 5

EXP 2

GA-FC

There are many other ways to connect the SDE-3000D.

For details, refer to “Connecting an Amp and Conguring the Input/

Output Settings” (p. 9).

Turning the Power On

* Before turning the unit on/o, always be sure to turn the volume

down. Even with the volume turned down, you might hear some

sound when switching the unit on/o. However, this is normal and

does not indicate a malfunction.

1. Connect the AC adaptor to the DC IN jack.

This turns the power of the SDE-3000D on.

DC IN

AC adaptor

2. Turn on any connected devices rst, and then turn on

your guitar amp.

* Do this in reverse order when turning o the power.

* Unsaved data is lost when the power turns o. You must save any

data in advance that you want to keep.

* The bank and memory number that you were using when you

turned the power o are stored in memory, and are recalled when

you turn the unit back on.

Getting Ready

Attaching the Rubber Feet

You can attach the rubber feet (included) if necessary.

Attach them in the locations shown

* Using the unit without rubber feet may damage the oor.

* When turning the unit over, be careful so as to protect the buttons and knobs from damage. Also, handle the unit carefully; do not drop it.

Top Panel

6 2

Area Explanation

Controls

Press the top part of each button to increase the value, and

press the bottom part of each button to decrease the value.

Long-press a button to make its value change rapidly.

[TIME] buttons

Adjusts the delay time.

[FEEDBACK] buttons

Adjusts the delay feedback level.

[OUT] buttons

Adjusts the output level for the delay sound.

[RATE] buttons

Adjusts the cycle of the delay modulation.

[DEPTH] buttons

Adjusts the depth of the delay modulation.

A setting of zero turns the modulation o.

Memory

[1]–[4] buttons

Selects the memories.

Ø“Selecting a Memory” (p. 15)

[ ] [ ] buttonsã â

Switches the play screen in the following order: Input

level Parameter Õ Õ Tempo Õ Bank/memory

Bank

[BANK A] [BANK B] buttons

Switches between banks A and B.

You can select the bank C memories (C.01 and up) by

using your feet (p. 6).

Area Explanation

Delay settings

[FILTER] button

A delay lter. This gives you a natural-sounding eect

when you’re using the delay as an echo.

[TIME×2] button

Switches between delay time ranges.

O (×1): 0.0-1500 ms

On (×2): 0.0-3000 ms

[DELAY PHASE] button

Inverts the phase of the delay sound.

[MOD] button

Turns the modulation on/o.

[FEEDBACK PHASE] button

Inverts the phase of the delay sound’s feedback.

[DIGITAL DELAY 1] button (DDL 1) /

[DIGITAL DELAY 2] button (DDL 2)

Switches between the DDL 1 and DDL 2 parameter

displays.

When TIME LINK is OFF or OFFSET, you can switch

between time displays for the L channel (lights up

green) and the R channel (lights up ) of DDL 1/DDL 2.red

[SETUP] button

Congures the memory and system settings. Long-

press the button to turn the lock on/o. Other button

operations are disabled when the lock feature is

enabled.

Switches

[DDL 1] switch / [DDL 2] switch

Switches the DIGITAL DELAY 1/2 on and o.

[TAP/CTL 1] switch

Press this switch in specic intervals to set the delay

time. Also, use this for the CTL function and assign

setting functions.

You can select memories by pressing the [DDL 1] switch and

[DDL 2] switch at the same time, or by pressing the [DDL 2]

switch and [TAP/CTL 1] switch at the same time.

Ø“Selecting Memories via Foot Control” (p. 6)

Display

This shows various information depending on the operation.

Play screen

Ø“Switching Between Play Screen Displays” (p. 4)

Edit screen

ØSee the edit pages for details.

Panel Descriptions

Product specificaties

Merk:	Boss
Categorie:	Niet gecategoriseerd
Model:	SDE-3000D

Heb je hulp nodig?

Als je hulp nodig hebt met Boss SDE-3000D stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Boss

Boss Gigcaster 8 GSC-8 Handleiding

26 Maart 2024

Boss TU-80 Handleiding

4 Maart 2024

Boss Reverb RV-6 Handleiding

1 Maart 2024

Boss Reverb RV-200 Handleiding

7 December 2023

Boss GKC-AD Handleiding

5 September 2023

Boss SDE-3000D Handleiding

5 September 2023

Boss Modulation MD-500 Handleiding

4 September 2023

Boss GT-1000CORE Handleiding

4 September 2023

Boss Pocket GT Handleiding

4 September 2023

Boss Metal Zone MT-2W Handleiding

4 September 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Playtive IAN 327221 Handleiding

1 Mei 2024

Samsung UN32J4001AF Handleiding

1 Mei 2024

Bauknecht KSI 18GF2 P2 Handleiding

27 April 2024

Fakir Artemis TS 150 Handleiding

26 April 2024

Sony UTX-M03 Handleiding

26 April 2024

Sony URX-P03 Handleiding

26 April 2024

Sony WRU-806B Handleiding

26 April 2024

Sony UTX-B03 Handleiding

26 April 2024

Sony UTX-P03 Handleiding

26 April 2024

Sony ODS-L10 Handleiding

26 April 2024