Audio-Technica ATM710 Handleiding

Bekijk gratis de handleiding van Audio-Technica ATM710 (2 pagina’s), behorend tot de categorie Microfoon. Deze gids werd als nuttig beoordeeld door 16 mensen en kreeg gemiddeld 4.0 sterren uit 8 reviews. Heb je een vraag over Audio-Technica ATM710 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

CARDIOID CONDENSER VOCAL MICROPHONE

- Tailored for exacting detail, high-delity vocal reproduction with maxi-

mum impact and intelligibility.

- Excels in venues with controlled stage volume or in-ear monitoring.

- Cardioid polar pattern reduces pickup of sounds from the sides and rear,

improving isolation of desired sound source.

- Durable performance for professional applications.

- Superior anti-shock engineering for low handling noise.

- Multi-stage grille design offers excellent protection against plosives and

sibilance without compromising high-frequency clarity.

- Condenser design for studio-quality performance.

- Integral 80Hz HPF switch and 10 dB pad.

- Corrosion-resistant contacts from gold-plated XLRM-type connector.

- Rugged, all-metal design and construction for years of trouble-free use.

The ATM710 is intended for use in professional applications where remote

power is available. It required 11V to 52V DC phantom power, which may

be provided by a mixer or console, or by a separate, in-line source such

as the Audio-Technica AT8801 single-channel or AT8506 four-channel

phantom power supplies.

Output from the microphone’s XLRM-type connector is low impedance

(Lo-Z) balanced. The signal appears across Pins 2 and 3; Pin 1 is ground

(shield). Output phase is “Pin 2 hot” - positive acoustic pressure produces

positive voltage at Pin 2.

To avoid phase cancellation and poor sound, all mic cables must be wired

consistently: Pin 1-to-Pin 1, etc.

When using the ATM710 in settings with a stage monitor speaker, the

speaker should be located 180° off axis (at rear of the microphone). This

placement, in conjunction with the microphone’s uniform cardioid pickup

pattern, will virtually eliminate the possibility of undesired audio feedback.

An integral 80Hz hi-pass filter provides easy switching from a flat fre-

quency response to a low-end roll-off. The roll-off position reduces the

microphone’s sensitivity to popping in close vocal use. It also reduces the

pickup of low-frequency ambient noise (such as trafc, air-handling sys-

tems, etc.), room reverberation and mechanically coupled vibrations.

The ATM710 is also equipped with a switchable 10 dB pad that lowers the

microphones’s sensitivity, thus providing higher SPL capability for exible

use with a wide range of performers and system congurations.

Avoid leaving the microphone in the open sun or in areas where tempera-

tures exceed 40°C for extended periods. Extremely high humidity should

also be avoided.

FORM No. ATGC-L0026-06-E

Machida • Tokyo • Japan

SPECIFICATIONS

ELEMENTFixed-change back plate permanently

polarized condenser

POLAR PATTERNCardioid

FREQUENCY RESPONSE40-20,000 Hz

LOW FREQUENCY ROLL-OFF80 Hz, 12 dB/octave

OPEN CIRCUIT SENSITIVITY-40 dB (10.0 mV) re 1V at 1 Pa

IMPEDANCE200 ohms

MAXIMUM INPUT SOUND LEVEL148 dB SPL, 1 kHz at 1% T.H.D.

DYNAMIC RANGE (typical)127 dB, 1 kHz at Max SPL

SIGNAL-TO-NOISE RATIO73 dB, 1 kHz at 1 Pa

PHANTOM POWER REQUIREMENTS11-52V DC, 3.5 mA typical

SWITCHESFlat, roll-off; 10 dB pad

WEIGHT274 g

DIMENSIONS179.0 mm - long,

50.0 mm - diameter

OUTPUT CONNECTORIntegral 3-pin XLRM-type

ACCESSORIES FURNISHEDAT8470 Quiet-Flex™ stand clamp for

⅝”-27 threaded stand;

⅝”-27 to ⅜”-16 threaded adapter;

Soft protective pouch

10 dB

20k10k5k2k1k50020010050

8 kHz

200 Hz

1 kHz

5 kHz

0°

330°

300°

270°

240°

210°

180°

150°

120°

90°

60°

30°

Polar Pattern

Frequency Response

SCALE IS 5 DECIBELS PER DIVISION

LEGEND

Frequency in Hertz

LEGEND 12” or more on axis

Response in dB

Roll-off

Product specificaties