Audio-Technica AT882TL/SS Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Audio-Technica AT882TL/SS (2 pagina's) in de categorie Microfoon. Deze handleiding was nuttig voor 27 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
Description
The AT882TL/SS requires a phantom power supply of 11–52V DC for each element. Output is low-
impedance balanced. The balanced signal appears across Pins 2 and 3, while the ground (shield)
connection is Pin 1. Output is phased so that positive acoustic pressure produces positive voltage
at Pin 2, in accordance with industry convention.
Each of the elements in the microphone is shock mounted. The Line-cardioid polar pattern of the
elements provides a 90°angle of acceptance. The AT882TL/SS is designed with integral wind-
screens to ensure maximum security against wind noise and plosives.
The microphone features a rubber switch that toggles between on/mute in Channel A (red
output), and a LED indicator that displays On status. This switch does not affect the output of
Channel B.
The microphone is enclosed in a sturdy metal housing with a low-reflectance black finish. Its base
is a desk stand that connected with a 2 meter splitter cable, which terminates in two 3-pin XLRM-
type connectors, for in-house and remote feeds.
The AT882TL/SS is intended for use on a flat surface. The 2 meter splitter cable terminates in two
3-pin XLRM-type connectors, which can be connected to in-house and/or remote feeds. Connect
the red output (Channel A) to the primary in-house feed. Connect the gray output (Channel B) to
the remote feed.
Avoid leaving the microphone in the open sun or in areas where temperatures exceed 43°C for
extended periods. Extremely high humidity should also be avoided.
Features
Designed for quality sound reinforcement in demanding situations, especially those
requiring separate miking for PA and broadcast.
Dual-element Line-cardioid condenser microphone with two independent power
module.
A rubber switch with LED allows users to easily mute/un-mute the Channel A (red
output) signal of microphone.
Circuit grounds for each channel are completely isolated, greatly reducing the potential
for hum.
Integral windscreens ensure ultimate security against wind noise and plosives.
Sturdy metal housing design with ball-in-socket base permits flexible positioning.
Heavy die-cast case and rubber bottom pads minimize coupling of surface vibration to
the microphones.
Specifications
Element Dual back electret condenser
Polar pattern Line-cardioid (Unidirectional)
Frequency response 20-20,000 Hz
Open circuit sensitivity -31 dB (28.2 mV) re 1V at 1 Pa
Impedance 100 ohms
Maximum input sound level 126 dB SPL, 1 kHz at 1% T.H.D.
Signal-to-noise ratio >69 dB, 1 kHz at 1 Pa
Phantom power requirements 11-52V DC, 2 mA typical
Switch Push button control: Channel A on/mute
Weight 1.22 kg
Dimensions 214 mm - long,
227 mm - Max. height,
102 mm - Width
Cable 2 m long, vinyl-jacketed stereo cable
Output connector Two 3-pin XLRM-type
polar pattern
SCALE IS 5 DECIBELS PER DIVISION
LEGEND
10 dB
20k10k5k2k1k50020010050
LEGEND
frequency response
Frequency in Hertz
Response in dB
12” or more on axis
Audio-Technica Corp. Machida Tokyo Japan 2018 NOV FORM No. ATGC-L0362-18-E
Optional Accessories:
AT8201 line matching transformer (Lo-z to
50,000 ohms)
AT8202 adjustable in-line attenuator for use
with low-impedance microphones.
AT8506 four-channel 48V phantom power
supply (AC powered).
Dual-element Line-cardioid Condenser Microphone (with Single channel Switch and LED)
AT882TL/SS
AT 8 8 2 T L / S S 使11V52V
频输出,终端音频线信号以两组卡农公头的2号及3号针脚输出,而1号
线( ) 2
Y3X L R M 线
话筒内配置有两组超指向的收音头,各可以提供 90°收音角度,
AT 8 8 2 T L / S S
A ( )
LEDB
2 长 Y
3X L R M 线
AT 8 8 2 T L / S S 适 用 于 平 面 放 置 , 2 米 长 的 Y 型 分 路 接 线 分 别 接 上 两 个 3 针
X L R M 卡农接头,可连接到内部主音和/或远程传送。可将红色输出(通
A)(B)远 传
筒留在日晒的地方或长时间置于温度超过 4 3 ° C 的地方,而极高湿度也应
避免。
技术指标
收音头
双元件背板静电型电容式
指向特性
超指向性
频率响应
20-20,000 Hz
开通灵敏度
-31 dB (28.2 mV) 1V 1 Pa
输出阻抗
100
最大承受声压
126 dB , 1 kHz 1% T.H.D.
信噪比
>69 dB, 1kHz 1 Pa
幻象供电
11-52V, 2 mA
: A /
1.22
外形尺寸
214 mm - ,
227 mm - ,
102 mm -
连接线
2米长,聚乙烯护套立体声电缆
输出连接器
两路3针卡农公头于输出端
声压曲线1刻度5 dB
频率
10 dB
20k10k5k2k1k50020010050
电平
频率 (赫兹)
响应电平 (dB)
平直
双音头超指向性电容话筒(LED)
AT882TL/SS
广广
应用。
LEDA()
整合了双网层防风罩,可减低环境噪声及风声。
置,以达到最佳收音效果。
及震动声。
选择配件:
AT8201 话筒线路匹配变压器
(低阻抗至50,000欧姆)。
AT8202 可选式低阻抗话筒
电平衰减器。
AT8506 四通通48V幻象供电器
(交流供电)。
FORM No. ATGC-L0362-18-CAudio-Technica Corp. Machida Tokyo Japan 2018 NOV


Product specificaties

Merk: Audio-Technica
Categorie: Microfoon
Model: AT882TL/SS

Heb je hulp nodig?

Als je hulp nodig hebt met Audio-Technica AT882TL/SS stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Microfoon Audio-Technica

Handleiding Microfoon

Nieuwste handleidingen voor Microfoon