Audio-Technica AE6100 Handleiding

Bekijk gratis de handleiding van Audio-Technica AE6100 (2 pagina’s), behorend tot de categorie Microfoon. Deze gids werd als nuttig beoordeeld door 17 mensen en kreeg gemiddeld 4.0 sterren uit 6 reviews. Heb je een vraag over Audio-Technica AE6100 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

User Manual

Hypercardioid Dynamic Handheld Microphone AE6100

■Features

■Notes on use

■Connection procedure

Outp nsuttermial

PIN1 (ground)

PIN3

(cold)

PIN2 (hot)

■Specifications

Dynamic

Hypercardioid

60 - 15,000 Hz

-55 dB (1.7 mV) re 1V at 1 Pa

250 ohms

310 g

177.0 mm long, 48.0 mm head diameter,

33.0 mm to 22.0 mm tapered body diameter

Integral 3-pin XLRM-type

AT8470 Quiet-Flex stand clamp for 5/8"-27 threaded stands;

5/8"-27 to 3/8"-16 threaded adapter;

soft protective pouch

•1 Pascal = 10 dynes/cm2 = 10 microbars = 94 dB SPL

*Typical, A-weighted, using Audio Precision System One.

■Pratternola p

■Fr roeequencyespns

180°

150°

120°

30°

0°

330°

300°

270°

240°

210°

Audio-Technica Corporation

2-46-1 Nishi-naruse, Machida, Tokyo 194-8666, Japan

©2017 Audio-Technica Corporation

Global Support Contact: www.at-globalsupport.com

14-DEC--2020 Form No.ATGC-L0391-20

LEGEND

0°, 50cm

SCALE IS 5 DECIBELS PER DIVISION

LEGEND

200 Hz

1 kHz

5 kHz

8 kHz

Thank you for purchasing this product. Before using the product, read through the user manual to

ensure that you will use the product correctly.

Please keep this manual for future reference.

Output from the microphone’s XLRM-type connector is low impedance (Lo-Z) balanced. The

signal appears across Pins 2 and 3; Pin 1 is ground (shield). Output phase is “Pin 2 hot” – positive

acoustic pressure produces positive voltage at Pin 2.

To avoid phase cancellation and poor sound, all mic cables must be wired consistently: Pin

1-to-Pin 1, etc. For a high-impedance (Hi-Z) mic input, connect a Lo-Z balanced cable to a Hi-Z

matching transformer (A-T CP8201 or equal) at the equipment input.

When using the AE6100 in settings with a stage monitor speaker, the speaker should be located

135° off axis (45° off the rear of the microphone). This placement, in conjunction with the

microphone’s uniform hypercardioid pickup pattern, will virtually eliminate the possibility of

undesired audio feedback.

The high sensitivity of the AE6100 assures useful output and an excellent match to most input

sources. In some cases, however, an attenuator such as the Audio-Technica AT8202 may be

required between the microphone and preamplifier to avoid overloading sensitive input stages.

Take care to keep foreign particles from entering the windscreen. An accumulation of iron or

steel filings on the diaphragm, and/or foreign material in the windscreen’s mesh surface, can

degrade performance.

Connect eas a microphone input the output terminals of the microphone to a dvice that h

(balanced input). The output connector is an XLRM-type with polarity as shown in the figure

below.

For product improvement, the product is sublect to modification without notice.

• Dynamic element gives pristine natural sound quality

• Tailored for an outstanding on-axis response

• Hardened steel body and grille for rugged durability

• High output, fast transients and clean articulation

• Multi-stage grille for reduced plosives and sibilance

• Superior anti-shock engineering for low handling noise

• Ergonomic design for easy handling

• Quiet-Flex stand clamp included for silent, flexible mic positioning

■Safety precaution

■Cautions for the product

Although this product was designed to be used safely, failing to use it correctly may result in an

accident. To ensure safety, observe all warnings and cautions while using the product.

• Do not subject the product to strong impact to avoid malfunction.

• Do not disassemble, modify or attempt to repair the product.

• Do not handle the product with wet hands to avoid electric shock or injury.

• Do not store the product under direct sunlight, near heating devices or in a hot, humid or dusty

place.

Element

Polar pattern

Frequency response

Open circuit sensitivity

Impedance

Weight

Dimensions

Output connector

Accessories furnished

60°

90°

Response in dB

Frequency in Hertz

10

0

-10

-20

-30

20

5001005020010k5k1k 2k20k

10 dB

Product specificaties