Atoll PR 200 Sig Handleiding

Bekijk gratis de handleiding van Atoll PR 200 Sig (4 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 8 mensen en kreeg gemiddeld 4.1 sterren uit 7 reviews. Heb je een vraag over Atoll PR 200 Sig of wil je andere gebruikers van dit product iets vragen? Stel een vraag

ATOLL ELECTRONIQUE

OWNER’S MANUAL ~ PREAMP

PR200 Sig

ATOLL ELECTRONIQUEPage 5Page 4

11) Bluetooth® receiver.

12) Coaxial inputs 1 & 2.

13) Optical inputs 1 & 2.

14) USB-B input.

DETAIL OF FUNCTIONS

Optional Digital Board

17) AUX input or Coaxial 1

18) CD input or Coaxial 2.

19) TU input or Optical 1.

20) DVD input or Optical 2.

21) TAPE input or USB.

22)BY-PASS input or Bluetooth®.

23) Digital/Analog indicator

(3)

.

24) Headphones jack.

25) Volume control.

26) IR receiver.

27) Inputs selector

(3)

.

28) Stand-by key.

CONNECTING

(2)

TAPE input/output - Monitoring loop:

The Tape function allows the recording of music from any source. Select your source

then press the Tape button for about 3 seconds. The Tape led (21) lights up and

indicates that the monitoring loop is active. This function can be used to insert a filter

(equalizer type).

(3)

Selection of D/A sources (Digital/analogue):

The source selection is made with the keys (27). To switch from analog sources

to digital sources (if you have this option), you must press these 2 buttons

simultaneously. When digital sources are selected, the indicator (23) lights up.

An optional remote control is available. It is equipped with 2 Lithium CR2025

batteries. This remote control is also able to drive all others ATOLL’s products: CD

players; Tuner; DACs.

REMOTE CONTROL

(*)

MUTE key: to get off the Mute, press any active key of the remote control.

(1)

Access to inputs OPT1 – OPT2 – COAX1 – COAX2 – USB – BT is only possible if

your appliance is equipped with the digital board.

Careful: Reduce the volume of the source connected to BY-PASS before any use of the

BY-PASS Input. The BY-PASS Input offers you the capacity to pass threw your preamplifier

so the signal goes directly to the power amplifier with no attenuation. Use it to plug

the output of an A/V processor. To avoid any trouble you can select this mode only

via the front panel of preamplifier or with the BY-PASS key of the remote control (hold

3 seconds.). Once selected, mention “BY-PASS” appears on display. Then, no other

functions are. Press once more BY-PASS to get back from BY-PASS mode.

USING OF THE BY-PASS INPUT

Optional Digital Board

12345678910

11121314

1) Aux input (or phono/SPDIF).

2) CD input.

3) Tuner input.

4) DVD input.

5) Tape input (IN-PLAY)

(2)

.

6) Tape output (OUT-REC)

(2)

.

7)BY-PASS input.

8) Preamp outputs (to 1 or 2 power

amplifier or to a subwoofer).

9) Trigger output

(1)

.

10) Switch ON/OFF and general plug-in

(with protection fuse).

(1)

Trigger output: this output is used to control the switching

off/on of any device equipped with a compatible Trigger

input (see instructions for use).

Trigger cable must be a stereo Male to Male jack plug

Ø 3,5 mm (1/8”).

Jack

Ø 3,5 mm

17

181920212223

25

26

24

2728

Direct access to sources

(1)

Sources selection

–

&

+

(except BY-PASS)

Mute

(*)

Stand-by

Display menu

Selection

of digital

inputs

BY-PASS selection (hold 3 sec)

Volume

+

Non-

func-

tional

keys

Product specificaties