Apc BX500CI Handleiding

Apc Server BX500CI

Lees hieronder de 📖 handleiding in het Nederlandse voor Apc BX500CI (1 pagina's) in de categorie Server. Deze handleiding was nuttig voor 32 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1

Troubleshooting and Service

1. Consult the Troubleshooting from the APC by Schneider Electric Web site, www.apc.com.

2.If the problem persists, contact Schneider Electric IT (SEIT) Customer Support through the

APC by Schneider Electric Web site, www.apc.com.

a. Note the model number and serial number and the date of purchase. The model and

serial numbers are located on the rear panel of the unit and are available through the

LCD display on select models.

b. Call SEIT Customer Support and a technician will attempt to solve the problem over

the phone. If this is not possible, the technician will issue a Returned Material

Authorization Number (RMA#).

c. If the unit is under warranty, the repairs are free.

d. Service procedures and returns may vary internationally. Refer to the APC by

Schneider Electric Web site for country specific instructions.

3. Prepare to troubleshoot the problem over the phone. If this is not successful, and the unit is

still under warranty, the Technical Support Representative will provide all necessary

information to return the unit for replacement.

Back-UPS

BX500CI

Adjust Transfer Voltage and

Sensitivity Settings

User Guide

™

Place the Back-UPS to avoid:

• Direct sunlight

• Excessive heat

• Excessive moisture

Connect the battery by pulling the battery

connector handle down, and then pushing it

into the unit.

Plug the Back-UPS BX500CI power cord directly into a wall outlet; not into a

surge protector or power strip.

Press the ON/OFF button to turn on the unit.

The green LED status indicator confirms that the Back-UPS is on and ready to

provide protection.

The Back-UPS should charge for at least 10 hours to ensure sufficient runtime.

The unit is being charged whenever it is connected to AC power, whether the

unit is turned ON or OFF.

Place and Power On

Battery Replacement

The battery in the Back-UPS BX500CI is not user-replaceable. Contact SEIT Technical Support for a

list of authorized service centers near you.

Warranty

The standard warranty is two (2) years from the date of purchase. SEIT standard procedure is to

replace the original unit with a factory reconditioned unit. Customers who must have the original unit

back due to the assignment of asset tags and set depreciation schedules must declare such a need at

ﬁrst contact with an SEIT Technical Support representative. SEIT will ship the replacement unit once

the defective unit has been received

by the repair department, or cro

ss-ship upon the receipt of a valid

credit card number. The customer pays for shipping the unit to SEIT. SEIT pays ground freight trans-

portation costs to ship the replacement unit to the customer.

APC by Schneider Electric IT Customer

Support Worldwide

For country specific customer support, go to the APC by Schneider Electric Web site, www.apc.com.

EN 990-5174 07/2013

by Schneider Electric Industries S.A.S. or their affiliated companies. All other trademarks are property of

their respective owners.

bu054a

ON/OFF

button and

LED Status

Indicator

Battery

connector

Battery

backup

and surge

protected

outlets

Speciﬁcations

Input Voltage / Frequency 230 VAC nominal / 45-65 Hz

Brownout Transfer /

Over-voltage Transfer

160 ±8% VAC, typical /

280 VAC, typical

Output UPS Capacity (total) 500 VA / 300 W

Voltage On Battery 230 Vac rms

Frequency - On Battery 50 Hz, 60 Hz ±1 Hz

Transfer Time 50 Hz: 6ms typical, 10ms maximum

60 Hz: 5ms typical, 8ms maximum

Protection

and Filter AC Surge Protection 273 joules

AC Input Resettable circuit breaker

Battery Type (maintenance-free) Sealed, lead-acid battery

Average Life 2 - 5 years depending on the number of

discharge cycles and environmental

temperature

Typical Recharge Time 10 Hours

Physical Net Weight 5.1 kg

Dimensions (H x W x D) 18.55 cm x 11.5 cm x 21.3 cm

Status Indicators

Automatic Voltage Regulation boosts the AC voltage when it drops below safe levels. This allows

the equipment plugged into the unit to operate

during low voltage c

onditions, conserving the

battery power in the event of a power cut.

The Back-UPS will switch to battery power if the input voltage level becomes too low for the

Automatic Voltage Regulation to compensate, or if the AC power is distorted.

If the Back-UPS switches to battery power too frequently or too infrequently, adjust the transfer

voltage and sensitivity settings:

1. Ensure the Back-UPS is off. Plug it into AC power.

2. Press and hold the ON/OFF button until the LED repeatedly flashes. The unit is now in

Program Mode.

3. Release the button. The LED will flash once, twice, or three times per second, indicating the

current setting.

4. Press the ON/OFF button within two seconds to change the setting. Each time the button is

pressed, the LED will flash at a different rate: once, twice, or th r second, ree times pe

indicating the new setting. Continue pressing the button until

the desired sett

ing is reached.

If the button is not pressed within five seconds, the Back-UPS will exit the Program Mode.

5. To exit Program Mode, release the button and wait for the LED to stop flashing.

Transfer Voltage and Sensitivity Settings

LED Flashing

Voltage

Sensitvity

Setting

Input Voltage

Range (for AC

Operation)

Usage

Once per second Low 155 - 280 The Back-UPS will switch to battery

power less often. Use with equipment

that is not sensitive to low or high

level voltage levels or minor voltage

waveform distortions.

Twice per second Medium

(factory

default)

160 -280 Default, use in normal conditions.

Three times per

second

High 165 - 270 The Back-UPS will switch to battery

power during any small fluctuation in

voltage. Use with equipment that is

sensitive to low or high level voltage

levels or minor voltage waveform

distortions.

LED Status

Indicator Audible Alarm Condition

On Off On-line - UPS is supplying conditioned AC power

to the load

On (Off

during 4

beeps)

4 beeps repeated

every 30

seconds

On-Battery - Back-UPS is supplying battery

power

Flashing Rapid Beeping

(every 1/2

second)

Low Battery Warning - The UPS has 1.5 minutes

of remaining battery power

Flashing Constant tone Bad Battery Detected - Battery needs to be

charged, or is at end of life.

Off Short beep every

4 seconds

Low Battery Shutdown - During On Battery

operation the battery power was almost completely

exhausted

Off Constant Tone On Battery Overload - Connected equipment

requires more power than provided by the Back-

UPS battery.

On Constant Tone On Line Overload - The power drawn by the

connected equipment exceeds the power capacity

of the battery backup

Flashing Chirp every 2

seconds

Charger Warning - Back-UPS has experienced an

internal problem, but continues to power the load.

Contact Schneider Electric IT (SEIT) Technical

Support.

Off Constant Tone Charger Fault - Back-UPS has an internal

problem, and is no longer powering the load.

Contact SEIT Technical Support

IEC jumper cable for

PC connection

AC power cable

Product specificaties

Merk:	Apc
Categorie:	Server
Model:	BX500CI
Kleur van het product:	Zwart
Gewicht:	5200 g
Breedte:	115 mm
Diepte:	213 mm
Hoogte:	185 mm
Snoerlengte:	1.83 m
Geluidsniveau:	45 dB
Gewicht verpakking:	5680 g
Breedte verpakking:	190 mm
Diepte verpakking:	291 mm
Hoogte verpakking:	257 mm
Gebruikershandleiding:	Ja
LED-indicatoren:	Batterijvervanging
Vormfactor:	Tower
Accu/Batterij voltage:	12 V
Certificering:	CE, REACH, PEP, EOLI
Geluidsalarm(en):	Ja
Duurzaamheidscertificaten:	RoHS,ENERGY STAR
Uitgangsvermogen:	300 W
Batterij capaciteit:	7.2 Ah
Temperatuur bij opslag:	-15 - 45 °C
Frequentie:	45/65 Hz
Luchtvochtigheid bij opslag:	0 - 95 procent
Hoogte, in bedrijf:	0 - 3000 m
Hoogte bij opslag:	0 - 15000 m
Stekker:	C14 stekker
Efficientie:	98.7 procent
Hoeveelheid per (buitenste) hoofdverpakking:	2 stuk(s)
Producten per pallet:	60 stuk(s)
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 95 procent
Batterijtechnologie:	Sealed Lead Acid (VRLA)
Code geharmoniseerd systeem (HS):	85078000
Surge energy rating:	273 J
Aantal AC uitgangen:	3 AC-uitgang(en)
Nominale input voltage:	230 V
Stopcontacttypes:	C13 stekker
Stroom (max.):	2 A
Output power capacity:	0.5 kVA
Ingang operation voltage (min):	160 V
Ingang operation voltage (max):	280 V
Uitgang operation voltage (min):	- V
Uitgang operation voltage (max):	- V
UPS-topologie:	Line-interactive
Typische backup tijd op halve lading:	7.6 min
Typische backup tijd op volledige lading:	1.3 min
Netspanning, in bedrijf:	230 V
Hoorbare alarmstanden:	Low battery alarm,Overload alarm
Spanningsbeveiliging:	Ja
Golfvorm:	Sinus
Uitgangsfrequentieregeling:	50 Hz
Automatic Voltage Regulation (AVR):	Ja
Number of output IEC jumpers:	1
Contacttijd (max):	10 ms
Contacttijd (min):	6 ms
Automatische batterij test:	Ja