Apc Back- 500VA Handleiding

Bekijk gratis de handleiding van Apc Back- 500VA (8 pagina’s), behorend tot de categorie UPS. Deze gids werd als nuttig beoordeeld door 15 mensen en kreeg gemiddeld 4.9 sterren uit 4 reviews. Heb je een vraag over Apc Back- 500VA of wil je andere gebruikers van dit product iets vragen? Stel een vraag

1

Place the Back-UPS to avoid:

– Direct sunlight

– Excessive heat

– Excessive humidity or contact with fluids

bu054a

ON/OFF and

LED Status

Indicator Battery backup and

surge protected outlets

2

3

990-3333B-005 © 2009 American Power Conversion Corp.

All other trademarks are property of their respective owners.

APC, Back-UPS and PowerChute are registered trademarks of American Power Conversion Corp.

Connect the Battery and Turn on the Unit

Connect the battery to the UPS before use. To connect the battery:

 Pull the top of the battery connector lever out of the unit, until the lever is horizontal.

 Push the battery connector lever completely into the unit, until the end of the lever is flush with the rear panel.

Press ON/OFF to turn on the unit.

A single short beep, and the green “Power On” indicator confirms that the Back-UPS is on and ready to provide

protection.

The Back-UPS should charge for at least 10 hours to ensure sufficient runtime. The unit is being charged

whenever it is connected to utility power, whether the unit is turned ON or OFF.

Status Indicators

The Back-UPS indicates its operating status using a combination of visual and audible indicators.

Power On LED BuzzerCondition

OnOff On-line - Back-UPS is supplying conditioned utility power

to the connected equipment

On (Off during 4

beeps) 4 beeps repeated

every 30 seconds

On-Battery- Back-UPS is supplying battery power

FlashingRapid Beeping

(every 1/2 second)

Low Battery Warning - The Back-UPS has 1.5 minutes of

remaining battery power

FlashingConstant toneBad Battery Detected - Battery needs to be charged, or is

at end of life. (See Battery Replacement.)

OffShort beep every

4 seconds

Low Battery Shutdown - During On Battery operation the

battery power was almost completely exhausted, and the

Back-UPS is waiting for utility power to return to normal

OffConstant ToneOn Battery Overload - Connected equipment requires

more power than provided by the Back-UPS battery.

Unplug devices one at a time to remove overload, if not

corrected Contact APC Technical Support

On Constant Tone On Line Overload - The power drawn by the connected

equipment exceeds the power capacity of the Battery

Backup

Flashing Chirp every 2

seconds

Charger Warning -Back-UPS has experienced an internal

problem, but continues to power the load. Contact APC

Technical Support

OffConstant ToneCharger Fault - Back-UPS has an internal problem, and is

no longer powering the load. Contact APC Technical

Support

Adjusting Transfer

Voltage and Sensitivity

Settings

Automatic Voltage Regulation boosts the utility voltage

when it drops below safe levels. This allows the

equipment plugged into the unit to operate during low

voltage conditions, conserving the battery power in the

event of a power outage.

The Back-UPS will switch to battery power if the input

voltage level becomes too low for the Automatic

Voltage Regulation to compensate, or if the utility

power is distorted.

If the Back-UPS switches to battery power too

frequently or too infrequently, adjust the transfer

voltage and sensitivity settings:

1. Ensure the Back-UPS is off. Plug it into utility

power.

2. Press and hold ON/OFF until the LED repeatedly

flashes. The unit is now in Program Mode.

3. Release the button. The LED will flash once,

twice, or three times per second, indicating the

current setting. See Transfer Voltage and

Sensitivity Settings.

4. Press ON/OFF within two seconds to change the

setting. Each time the button is pressed, the LED

will flash at a different rate: once, twice, or three

times per second, indicating the new setting.

Continue pressing the button until the desired

setting is reached. If the button is not pressed

within five seconds, the Back-UPS will exit the

Program Mode.

5. To exit Program Mode, release the button and

wait for the LED to stop flashing.

Connect Equipment

Battery Backup Surge Protection

These outlets are powered whenever the Back-UPS is switched

ON. During a power outage, or other utility problems (brownouts,

over-voltages), these outlets will be powered for a limited time by

the Back-UPS. Plug the computer and monitor into these two

outlets.

Connect AC Power Cord

Plug the Back-UPS power cord into a wall outlet, not a surge

protector or power strip. The outlet should be near the equipment

and easily accessible.

Back-UPS® RS 500

BR500CI-AS User Guide

Transfer Voltage and Sensitivity Settings

LED FlashingTransfer Voltage

Setting

Input Voltage

Range

(For Utility

Operation)

Usage

Once per secondLow155 - 280The Back-UPS will switch to battery power less often. Use with equipment that is not

sensitive to low or high level voltage levels or minor voltage waveform distortions.

Twice per secondMedium

(factory default)160 -280Default, use in normal conditions.

Three times per second

High165 - 270The Back-UPS will switch to battery power during any small fluctuation in voltage.

Use with equipment that is sensitive to low or high level voltage levels or minor

voltage waveform distortions.

bu053a

Product specificaties