Antec BP430 Handleiding

Antec Computervoeding BP430

Lees hieronder de 📖 handleiding in het Nederlandse voor Antec BP430 (4 pagina's) in de categorie Computervoeding. Deze handleiding was nuttig voor 26 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4

Basiq

BP430

User’s Manual

Manuel de l’utilisateur

Anwenderhandbuch

Manuale per l’operatore

Manual del usuario

Ё᭛Փ⫼᠟ݞ

পᡅ䂀ᯢ᳌

Antec Basiq User’s Manual

ATX12V version 2.2 power supply

Model BP430

Antec Basiq series power supplies are built to be compatible with the ATX12V

version 2.2 specification. They include two 12V output circuits that deliver safer

and more reliable output to your system’s components. In addition we’ve

included a variety of protective circuitry: OCP (Over Current Protection),

OVP (Over Voltage Protection), and SCP (Short Circuit Protection).

BP430 includes Universal Input with Active Power Factor Correction (PFC).

Universal Input allows you to connect your Antec Basic power supply to any AC

power outlet between 100~240V without having to worry about setting a voltage

switch. Active PFC improves the power factor value to the power supply by altering

the input current wave shape, helping the power plant provide power to users

more efficiently.

Power Switch:

This power supply comes with a main power switch. Make sure you turn the

switch to the ON ( I ) position before you boot up your computer for the first time.

In normal operation there is no need to turn the switch to the OFF (O) position

since the power supply is equipped with a soft on/off feature which turns your

computer on and off through the soft switch on your computer case. You may

need to turn the switch to the OFF position occasionally should your computer

crash and you cannot shut it down through use of the soft switch.

Installation:

1. Turn off the hard power switch on your old power supply if any.

2. Open your computer case. Follow the directions provided in your case manual.

3. Disconnect all power connectors from the motherboard and from the peripheral

devices such as case fans, hard drives, optical drives, floppy drives, etc.

4. Disconnect the power cord from your old power supply.

5. Remove the existing power supply from your computer case and replace it

with your new Antec power supply. (Illustration 1)

6. Turn the hard switch on the Antec power supply to the OFF (O) position and

connect the AC power cord to the power supply.

7. Connect the 24-pin Main Power Connector (Illustration 2). If the mother-

board uses a 20-pin connector, detach the 4-pin attachment on the 24-pin

power connector (see pictures 1 and 2).

Note: the detachable 4-pin section cannot be used

in place of a 4-pin +12V connector.

8. Connect the 4-pin (Illustration 3) 12V connector to the motherboard as

needed.

9. If your video card requires a PCI-E Connector, then connect the cable from

the main wire bundle to your video card.

10. Connect the Drives and Accessories Cable to devices such as hard drives,

optical drives, fans, etc.

11. Connect the SATA cable if you are using a Serial ATA hard drives.

12. Close your computer case.

Picture 1 Picture 2

For 24-pin

motherboards

For 20-pin

motherboards

Product specificaties

Merk:	Antec
Categorie:	Computervoeding
Model:	BP430
Kleur van het product:	Wit
Gewicht:	1450 g
Geluidsniveau:	- dB
Bedoeld voor:	PC
Stroomspanning bescherming:	Over current, Over power, Over voltage, Short circuit
80 PLUS certificatie:	80 PLUS
Mean time between failures (MTBF):	100000 uur
Totaal vermogen:	430 W
Afmetingen (B x D x H):	150 x 140 x 86 mm
AC-ingangsspanning:	100 - 240 V
AC-ingangsfrequentie:	50 - 60 Hz
Ventilator diameter:	80 mm
Motherboard power connector:	20+4 pin ATX
Peripheral (Molex) power connectors (4-pin):	4
Vormfactor van de voeding (PSU):	ATX
Power Factor Correctie (PFC) type:	Actief
Aantal SATA power connectors:	3
Floppy drive power connector:	1
ATX version:	2.2
PCI Express power connectors (6-pin):	1