American Standard Studio S 4803300 Handleiding
Pagina's 9 Niet gecategoriseerd
Bekijk de handleiding van American Standard Studio S 4803300 gratis online of download de PDF. Deze handleiding is 0 keer bekeken. Vraag over dit model? Stel een vraag
- 1 -
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2021
Thank you for selecting American Standard...
the benchmark of fine quality for over 140 years.
To ensure that your installation proceeds smoothly-please read
these instructions carefully before you begin.
RECOMMENDED TOOLS
1
M985011 Rev. 1.0 (5/21)
INSTALL FAUCET
Studio-S
®
Pull-Down Kitchen Faucet
Plumbers' Putty or CaulkingAdjustable WrenchPhillips ScrewdriverFlat Blade Screwdriver
Certied to comply with ANSI A112.18.1M
INSTALLATION
INSTRUCTIONS
4803300
Certied to comply with ANSI A112.18.1M
SPOUT BASE
1
4
3
2
5
6
8
7
2
• Make certain the SEAL is properly seated in recess of (1)
spout base.
• all HOSES and SHANK through MOUNTING Insert (2) (3)
RING and mounting surface. Do not use putty.(4)
• HOSES through RUBBER WASHER, BRASS Insert (2) (5)
WASHER, and threaded LOCKNUT . (6)(7)
• RUBBER WASHER, BRASS WASHER, and Assemble (5) (6)
threaded LOCKNUT onto SHANKfrom underside (7) (3)
of sink or mounting surface. Hand tighten LOCKNUT. (7)
• a screwdriver to tighten SCREWS on LOCKNUT . Use(8)(7)
Work your way around LOCKNUT , tightening the screws (7)
slightly each time until all are snug to ensure even pressure.
CAUTION
Turn off water at
main supply
- 2 -
2
M985011 Rev. 1.0 (5/21)
• Turn off hot and cold water supplies before beginning.
• Connect FLEXIBLE SUPPLY HOSESdirectly to wall (1, 2)
supplies. Connection on tting supplies are 3/8"
compression. Connect left supply hose (Red Stripe) to Hot
wall supply. Connect right supply hose (Blue Stripe) to Cold
wall supply. Use adjustable wrench to tighten connections.
Do not over tighten.
*
Faucet supplies are 32 " long from faucet base.
• Note: If additional supply length is required, installer
must purchase additional parts separately.
• Important: If SUPPLY HOSES (1, 2) are too long,
loop as illustrated to avoid kinking.
MAKE WATER SUPPLY CONNECTIONS
RED
STRIPE
BLUE
STRIPE
1
2
COLD
HOT
3
4
5
STREAM (AERATOR)
SPRAY
3
CONNECT SPRAY HOSE AND INSTALL WEIGHTS
2
3
1
REMOVE
COLD
ON
OFF
HOT
7
6
8
2
1
8
3
4
5
• the SPRAY HOSE END into the HOSE Push(1)
CONNECTOR and slide down the LOCKING (2)
COLLAR until it snaps into place.(3)
• HAND SPRAY seated in SPOUT , install With(4)(5)
WEIGHT at labeled area onto HOSE , secure (6)(7)
with SCREWS (8).
4
TEST INSTALLED FAUCET
• Turn ON water at main supply.
• HANDLE in “off” position, unthread SPRAY from HOSE . With(1)(3)(2)
• handle back to front, in COLD and HOT positions, to ush water Operate
lines thoroughly.
• Replace SPRAY (3)(2) onto HOSE .
SPRAY OPERATION
• With FAUCET on, press TOGGLE BUTTON on SPRAY to switch (4)(3)
from stream to spray.
• and hold PAUSE BUTTON to temporarily stop ow from SPRAY Press(5)
(3). Release PAUSE BUTTON to resume ow from SPRAY .(5)(3)
- 3 -
6
SERVICE
5
M985011 Rev. 1.0 (5/21)
• Move HANDLEinto “off” position.
• Turn on water supplies and check connections for leaks.
• HANDLE up and down, left and right to ush Operate
water lines thoroughly.
• Operate HAND SPRAY and check connections for leaks.
CHECK CONNECTIONS FOR LEAKS
CHECK CONNECTIONS
FOR LEAKS
2
1
3
5
5a
4
6
7
7
DO: CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS:
If Faucet Drips, Proceed As Follows:
• Turn VALVE to OFF position.
• Operate HANDLE several times from OFF to ON position. Do not apply excessive force.
Reduced Flow:
• Clean out spray head screen.
• Clean out cartridge.
Clogged CARTRIDGE outlets or inlets may
cause reduced flow.
To clean, rst turn off water supply then:
• Loosen HANDLE SCREW and remove (1)
HANDLE. (2)
• ESCUTCHEON CAP, Unthread (3)
SNAP RING. (4)
• CARTRIDGE off MANIFOLDand Lift(5) (6)
remove CARTRIDGE SEALS .(7)
• MANIFOLD, CARTRIDGE Clean (6) (5)
ports and SEALS. (7)
• SEALS into CARTRIDGE Place (7)
PORTS. (5a)
• CARTRIDGE onto MANIFOLD. Place(5) (6)
• ESCUTCHEON CAP, SNAP RING , Replace (3)(4)
HANDLE , tighten HANDLE (2)
SCREW. (1)
Product specificaties
| Merk: | American Standard |
| Categorie: | Niet gecategoriseerd |
| Model: | Studio S 4803300 |
Heb je hulp nodig?
Als je hulp nodig hebt met American Standard Studio S 4803300 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden