American Standard Edgewater 4932410 Handleiding
Pagina's 4 Niet gecategoriseerd
Bekijk de handleiding van American Standard Edgewater 4932410 gratis online of download de PDF. Deze handleiding is 1 keer bekeken. Vraag over dit model? Stel een vraag
- 1 -
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2021
Thank you for selecting American Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly-please read
these instructions carefully before you begin.
RECOMMENDED TOOLS
1
M965716 Rev. 1.3 (5/21)
INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON
EDGEWATER
™
Pull-Down Bar Faucet
INSTALLATION
INSTRUCTIONS
4932.410
4932.415
Plumbers' Putty or CaulkingAdjustable WrenchPhillips ScrewdriverFlat Blade Screwdriver
Certied to comply with ANSI A112.18.1M
CAUTION
Turn off water at
main supply
BA
(OPTIONAL)
SINK OR
MOUNTING
SURFACE
4
5
8
7
6
7
9
3
2
7
9
PUTTY
SPOUT BASE
SPOUT BASE
2
3
4
5
8
6
7
1
• (A) Installation with ESCUTCHEON (1). (Escutcheon is not supplied with base product). Apply a bead of putty to bottom
edge of ESCUTCHEON with PUTTY PLATE . Make certain the SEAL is properly seated in recess of faucet body. Insert (1)(9)
SUPPLY HOSES , SPRAY HOSE and SHANK through hole of ESCUTCHEON with PUTTY PLATE and mounting (2)(7)(3)(1)
surface. Follow mounting instructions below to secure faucet to mounting surface.
• (B) Installation less ESCUTCHEON (1). Make certain the SEAL is properly seated in recess of spout base. Insert supply (9)
HOSES , SPRAY HOSE and SHANK through mounting hole and seat spout base onto sink or mounting surface. (2)(7)(3)
Do not use putty.
• HOSES through RUBBER WASHER , BRASS WASHER , and threaded LOCKNUT . Insert(2)(4)(5)(6)
• RUBBER WASHER , BRASS WASHER , and threaded LOCKNUT onto SHANK from underside of sink Assemble(4)(5)(6)(3)
or mounting surface. Hand tighten LOCKNUT .(6)
• a screwdriver to tighten SCREWS on LOCKNUT . Work your way around LOCKNUT , tightening the screws Use(8)(6)(6)
slightly each time until all are snug to ensure even pressure.
- 2 -
2
M965716 Rev. 1.3 (5/21)
3
CONNECT SPRAY HOSE & INSTALL WEIGHTS
• Turn off hot and cold water supplies before beginning.
• Connect FLEXIBLE SUPPLY HOSESdirectly to wall (1, 2)
supplies. Connection on tting supplies are 3/8"
compression. Connect left supply hose (Red Stripe) to Hot
wall supply. Connect right supply hose (Blue Stripe) to Cold
wall supply. Use adjustable wrench to tighten connections.
Do not over tighten.
*
Faucet supplies are 21" long from faucet base.
• Note: If additional supply length is required, installer
must purchase additional parts separately.
• Important: If SUPPLY HOSES (1, 2) are too long,
loop as illustrated to avoid kinking.
MAKE WATER SUPPLY CONNECTIONS
• Push the SPRAY HOSE END into the HOSE CONNECTOR (2)
(1)(3) slide down LOCKING COLLAR until it snaps into place
to secure connection.
• HAND SPRAY seated in SPOUT , install With(4)(5)
WEIGHT at labeled area onto HOSE , secure (6)(7)
with SCREWS (8).
7
6
8
2
1
8
3
21"
(610 mm)
4
5
RED
STRIPE
BLUE
STRIPE
1
2
COLD
HOT
4
CHECK CONNECTIONS FOR LEAKS
• Move HANDLE into “off” position.
• on water supplies and check connections for leaks. Turn
• HANDLE up and down, left and right to Operate(1)
ushwater lines thoroughly.
• HAND SPRAY and check connections for leaks. Operate
CHECK CONNECTIONS
FOR LEAKS
- 3 -
6
7
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
SERVICE
CARE INSTRUCTIONS:
TEST INSTALLED FAUCET
5
M965716 Rev. 1.3 (5/21)
1
3
2
REMOVE
COLD
ON
OFF
HOT
1
2
3
4
5
6
• Move HANDLE into “off” position.(1)
• Turn on water supplies.
• Check connection for leaks. (See Section 4)
• HANDLE in “off” position, unthread With(1)
SPRAY from HOSE .(3)(2)
• handle back to front, in COLD Operate
and HOT positions, to ush water lines
thoroughly.
• Replace SPRAY onto HOSE .(3)(2)
If faucet drips, operate HANDLE several times from “off” to “on.” Do not apply excessive force.
Clogged CARTRIDGE outlets or inlets may cause reduced flow.
To clean, rst turn off water supply then:
• HANDLE SCREW and remove HANDLE . Loosen(1)(2)
• the SNAP RING . Unthread three MOUNTING SCREWS . Unthread(3)(4)
• CARTRIDGE off MANIFOLD . Lift(5)(6)
• MANIFOLD and CARTRIDGE ports. Clean(6)(5)
• CARTRIDGE onto MANIFOLD and Place(5)(6)
tighten MOUNTING SCREWS alternately.(4)
• SNAP RING , HANDLE , Replace(3)(2)
tighten HANDLE SCREW .(1)
Product specificaties
| Merk: | American Standard |
| Categorie: | Niet gecategoriseerd |
| Model: | Edgewater 4932410 |
Heb je hulp nodig?
Als je hulp nodig hebt met American Standard Edgewater 4932410 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden