Alto TS SUB 15 Handleiding

Alto Speaker TS SUB 15

Lees hieronder de 📖 handleiding in het Nederlandse voor Alto TS SUB 15 (8 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 26 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8
QUICKSTART GUIDE
ENGLISH
GUÍA DE INICIO RÁPIDO
ESPAÑOL
GUIDE D'UTILISATION RAPIDE
FRANÇAIS
GUIDA RAPIDA
ITALIANO
SCHNELLSTART-ANLEITUNG
DEUTSCH
SNELSTARTGIDS
NEDERLANDS
2
BOX CONTENTS
TRUESONIC subwoofer
Power cable
Quickstart Guide
Safety Instructions & Warranty Information Booklet
CONNECTION DIAGRAM
REAR PANEL OVERVIEW
1. POWER INPUT Connect the included power cable to this
input and connect the other end of the cable to a power
source. Make sure the subwoofer's POWER SWITCH is set
to "off" when plugging and unplugging the cable.
2. POWER SWITCH Turns the subwoofer on/off. Make sure
the VOLUME knob is set to "zero" before turning it on.
3. POWER LED – Illuminates when the subwoofer is on.
4. VOLUME – Turn this knob to adjust the subwoofer's volume.
5. INPUTS Use standard XLR cables (not included) to
connect your sound source to these inputs. The
"LEFT/MONO" INPUT can accept either 1/4" TRS or XLR
connections. (When connecting a mono sound source, use
only the "LEFT/MONO" INPUT.)
6. OUTPUTS Use standard XLR cables (not included) to
connect the subwoofer to the inputs of your speakers, which
can be active or passive.
7. LINK OUTPUT Use standard XLR cables (not included) to
connect the subwoofer to the inputs of an additional amplifier
(optional).
8. SIGNAL LIMIT LED Illuminates when the audio signal being sent to the subwoofer is "clipping" or distorting. If this
light illuminates frequently or steadily, reduce the volume of your sound source.
9. GROUND SWITCH – Depressing this switch grounds the subwoofer, which can reduce hum or noise.
10. PHASE SWITCH Depressing this switch reverses the polarity of the subwoofer's output signal. In some cases, this
can help reduce any interference in the frequency overlap between the subwoofer and main speaker.
11. BYPASS SWITCH – Depressing this switch activates the subwoofer's high-pass filter (80 Hz).
*
Note
:
Microphones, mixer, speakers, and
cables are not included.
Speaker* Speaker*
Microphones*
Power
Power
Subwoofer
Mixer*
1
2
3
4
5 5
7 7
6 6
8
9 10 11
3
CONTENIDO DE LA CAJA
Subwoofer TRUESONIC
Cable de alimentación
Guía de inicio rápido
Folleto de instrucciones de seguridad e información sobre la garantía
DIAGRAMA DE CONEXIÓN
VISTA DEL PANEL TRASERO
1. ENTRADA DE ALIMENTACIÓN Conecte a esta entrada el
cable de alimentación incluido y luego conecte el otro extremo
del cable al suministro eléctrico. Asegúrese de que el
INTERRUPTOR DE ENCENDIDO esté en "off" (apagado)
cuando enchufe y desenchufe el cable.
2. INTERRUPTOR DE ENCENDIDO Enciende y apaga el
altavoz. Asegúrese de que la perilla de VOLUMEN esté
ajustada a "cero" antes de encenderlo.
3. LED DE ENCENDIDO Se ilumina cuando el altavoz está
encendido.
4. VOLUMEN – Gire esta perilla para ajustar el volumen del
altavoz.
5. ENTRADAS Use cables XLR estándar (no incluidos) para
conectar su fuente de sonido a estas entradas. La ENTRADA
"IZQUIERDA/MONO" puede aceptar conexiones de 1/4" TRS
o XLR. (Cuando conecte una fuente de sonido mono, use
sólo la ENTRADA "IZQUIERDA/MONO".)
6. SALIDAS Use cables XLR estándar (no incluidos) para
conectar el subwoofer a las entradas de sus altavoces, que
pueden ser activos o pasivos.
7. SALIDA DE ENLACE Use cables XLR estándar (no incluidos) para conectar el subwoofer a las entradas de un
amplificador adicional (opcional).
8. LED DE LÍMITE DE SEÑAL – Se enciende cuando la señal de audio que se envía al altavoz se "recorta" o distorsiona.
Si esta luz se enciende con frecuencia o en forma permanente, reduzca el volumen de su fuente de sonido.
9. INTERRUPTOR DE TIERRA Al oprimir este interruptor, se pone a tierra el subwoofer, con lo que se puede reducir el
zumbido o ruido.
10. CONMUTADOR DE FASE – Al oprimir este conmutador se invierte la polaridad de la señal de salida del subwoofer. En
algunos casos, esto puede ayudar a reducir interferencias en el solapamiento de frecuencias entre el subwoofer y el
altavoz principal.
11. INTERRUPTOR DE DERIVACIÓN – Al oprimir este interruptor se activa el filtro pasaaltos del subwoofer (80 Hz).
*Nota: No se incluyen micrófonos, mezclador,
altavoces y cables.
Altavoz*
Micrófonos*
Potencia
Potencia
Subwoofer
Mezclador*
Altavoz*
1
2
3
4
5 5
7 7
6 6
8
9 10 11


Product specificaties

Merk: Alto
Categorie: Speaker
Model: TS SUB 15

Heb je hulp nodig?

Als je hulp nodig hebt met Alto TS SUB 15 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Speaker Alto

Handleiding Speaker

Nieuwste handleidingen voor Speaker