Alto TS SUB 12 Handleiding

Alto Speaker TS SUB 12

Lees hieronder de 📖 handleiding in het Nederlandse voor Alto TS SUB 12 (8 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 15 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8
QUICKSTART GUIDE
ENGLISH
GUÍA DE INICIO RÁPIDO
ESPAÑOL
GUIDE D'UTILISATION RAPIDE
FRANÇAIS
GUIDA RAPIDA
ITALIANO
SCHNELLSTART-ANLEITUNG
DEUTSCH
SNELSTARTGIDS
NEDERLANDS
2
CONNECTION DIAGRAM
REAR PANEL OVERVIEW
1. POWER INPUT Connect the included
power cable to this input and connect the
other end of the cable to a power source.
Make sure the subwoofer's POWER
SWITCH is set to "off" when plugging and
unplugging the cable.
2. POWER SWITCH Turns the subwoofer
on/off. Make sure the VOLUME knob is set
to "zero" before turning it on.
3. POWER LED Illuminates when the
subwoofer is on.
4. VOLUME Turn this knob to adjust the
subwoofer's volume.
5. INPUTS – Use standard XLR cables (not
included) to connect your sound source to
these inputs. The "LEFT/MONO" INPUT can
accept either 1/4" TRS or XLR connections.
(When connecting a mono sound source,
use only the "LEFT/MONO" INPUT.)
6. OUTPUTS Use standard XLR cables (not
included) to connect the subwoofer to the
inputs of your active speakers or powered amplifier.
7. LINK OUTPUT Use standard XLR cables (not included) to connect the subwoofer to the inputs of an
additional amplifier (optional).
8. SIGNAL LIMIT LED Illuminates when the audio signal being sent to the subwoofer is "clipping" or
distorting. If this light illuminates frequently or steadily, reduce the volume of your sound source.
9. GROUND SWITCH – Depressing this switch grounds the subwoofer, which can reduce hum or noise.
10. PHASE SWITCH Depressing this switch reverses the polarity of the subwoofer's output signal. In
some cases, this can help reduce any interference in the frequency overlap between the subwoofer
and main speaker.
11. BYPASS SWITCH – Depressing this switch activates the subwoofer's high-pass filter (80 Hz).
*Note: Microphones, mixer, speakers,
and cables are not included.
Speaker* Speaker*
Microphones*
Power
Power
Subwoofer
Mixer*
1
2
3
4
5 5
7 7
6 6
8
9 10 11
BOX CONTENTS
TRUESONIC subwoofer
Power cable
Quickstart Guide
Safety Instructions & Warranty
Information Booklet
3
DIAGRAMA DE CONEXIÓN
VISTA DEL PANEL TRASERO
1. ENTRADA DE ALIMENTACIÓN Conecte a esta
entrada el cable de alimentación incluido y luego
conecte el otro extremo del cable al suministro
eléctrico. Asegúrese de que el INTERRUPTOR DE
ENCENDIDO esté en "off" (apagado) cuando
enchufe y desenchufe el cable.
2. INTERRUPTOR DE ENCENDIDO Enciende y
apaga el altavoz. Asegúrese de que la perilla de
VOLUMEN esté ajustada a "cero" antes de
encenderlo.
3. LED DE ENCENDIDO Se ilumina cuando el
altavoz está encendido.
4. VOLUMEN Gire esta perilla para ajustar el
volumen del altavoz.
5. ENTRADAS Use cables XLR estándar (no
incluidos) para conectar su fuente de sonido a estas
entradas. La ENTRADA "IZQUIERDA/MONO"
puede aceptar conexiones de 1/4" TRS o XLR.
(Cuando conecte una fuente de sonido mono, use
sólo la ENTRADA "IZQUIERDA/MONO".)
6. SALIDAS Use cables XLR estándar (no incluidos)
para conectar el subwoofer a las entradas de sus altavoces activos o su amplificador alimentado.
7. SALIDA DE ENLACE Use cables XLR estándar (no incluidos) para conectar el subwoofer a las entradas de
un amplificador adicional (opcional).
8. LED DE LÍMITE DE SEÑAL Se enciende cuando la señal de audio que se envía al altavoz se "recorta" o
distorsiona. Si esta luz se enciende con frecuencia o en forma permanente, reduzca el volumen de su fuente
de sonido.
9. INTERRUPTOR DE TIERRA Al oprimir este interruptor, se pone a tierra el subwoofer, con lo que se puede
reducir el zumbido o ruido.
10. CONMUTADOR DE FASE Al oprimir este conmutador se invierte la polaridad de la señal de salida del
subwoofer. En algunos casos, esto puede ayudar a reducir interferencias en el solapamiento de frecuencias
entre el subwoofer y el altavoz principal.
11. INTERRUPTOR DE DERIVACIÓN Al oprimir este interruptor se activa el filtro pasaaltos del subwoofer (80
Hz).
*Nota: No se incluyen micrófonos, mezclador,
altavoces y cables.
Altavoz*
Micrófonos*
Potencia
Potencia
Subwoofer
Mezclador*
Altavoz*
1
2
3
4
5 5
7 7
6 6
8
9 10 11
CONTENIDO DE LA CAJA
Subwoofer TRUESONIC
Cable de alimentación
Guía de inicio rápido
Folleto de instrucciones de seguridad e
información sobre la
g
arantía


Product specificaties

Merk: Alto
Categorie: Speaker
Model: TS SUB 12

Heb je hulp nodig?

Als je hulp nodig hebt met Alto TS SUB 12 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Speaker Alto

Handleiding Speaker

Nieuwste handleidingen voor Speaker