Aiphone IX-BA Handleiding

Aiphone Intercomsysteem IX-BA

Lees hieronder de 📖 handleiding in het Nederlandse voor Aiphone IX-BA (4 pagina's) in de categorie Intercomsysteem. Deze handleiding was nuttig voor 24 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4

• Read this manual before installation and connection.

Read the "Setting Manual" and "Operation Manual" included on the DVD-ROM that comes with the

Master Station (IX-MV).

• Conﬁ gure the system settings according to the "Setting Manual" after completing the installation

and connection. The system will not function unless it has been properly conﬁ gured.

• After installation, explain to the customer how to use the device, and be sure to provide the

accompanying DVD-ROM that came with the Master Station (IX-MV).

Important

• Perform the installation and connection only after fully understanding this device and the manual.

Illustrations used in this manual may be different from the actual ones.

Mounting frame

Main unit

IX-DA

(Video Door Station)

IX-BA

(Audio Only Door Station)

Panel

Microphone

Communication

indicator (green)

Speaker

Call indicator (orange)

Call button

Camera

Microphone

LED for night illumination

Communication

indicator (green)

Speaker

Call indicator (orange)

Camera angle adjustment

lever (Video Door Station only)

CAT5e/6 cable

connections

Option connector input

Drain holes (4)

Status indicator (red)

Drain holes (4)

Status indicator (red)

Call button

Accessories included

Installation Manual

(this manual) x1

Option connector

Special screwdriver

Chinese RoHS paper

Wall mounting screws

Wall mounting

wood screws x2

MAC address

(beneath the panel)

MAC address

(beneath the panel)

MAC address

Reset button*

* Press and hold the reset

button for longer than 1

second, then release to

restart station.

Side Back

Warning Negligence could result in .death or serious injury

1. Voltage is applied to parts within the

equipment. Do not touch any parts that are

not associated with the installation, wiring,

or connection. Electric shock could result.

Dismantling

alteration

2. Do not dismantle or alter the unit.

Fire or electric shock could result.

3. Keep the unit away from water or any

other liquid.

Fire or electric shock could result.

4. The unit is not explosion-proof. Do not

install or use near gases or ﬂ ammable

materials.

Fire or explosion could result.

5. Do not connect any terminal on the unit

to an AC power line.

Fire or electric shock could result.

6. Do not put any metal or ﬂ ammable

material into the unit through the

openings.

Fire, electric shock, or unit trouble could

result.

Caution

Negligence could result in .injury to people or damage to property

1. Do not install or make any wire

terminations while power supply is

plugged in. It can cause electrical shock

or damage to the unit.

2. Before turning on power, make sure

wires are not crossed or shorted. If not,

ﬁ re or electric shock could result.

3. Do not install the unit in any of the

following locations. Fire, electric shock,

or unit trouble could result.

• Places under direct sunlight or places

near heating equipment that varies in

temperature.

• Places subject to dust, oil, chemicals,

hydrogen sulﬁ de (hot spring).

• Places subject to moisture and

humidity extremes, such as

bathrooms, cellars, greenhouses, etc.

• Places where the temperature is quite

low, such as inside a refrigerated area

or in front of an air conditioner.

• Places subject to steam or smoke (near

heating or cooking surfaces).

• Where noise generating devices

such as dimmer switches or inverter

electrical appliances are close by.

• Locations subject to extremely

powerful electric ﬁ elds.

4. When mounting the unit on a wall,

install the unit in a convenient location,

but not where it could be jarred or

bumped. Injury could result.

5. Do not place or install the unit in the

locations subject to frequent vibration or

impact. If the unit falls, injury to people

or damage to the unit could result.

6. Do not run wires between movable

objects (doors, windows, etc.). It may

cause malfunction.

7. Do not put anything on the unit or cover

the unit with cloth, etc. Fire or unit

trouble could result.

8. Be sure to perform a call test or check

the chime volume with the handset on

the hook. If you operate the hook switch

with the handset on your ear, a sudden

call etc. may arrive causing damage to

your ear.

Installation Manual IX-DA

(Video Door Station)

IX-BA (Audio Only Door Station)

Precautions

ecautions

ecautionsPrecautions

Intr

Introduction

oduction

oductionIntroduction

Example of

Example of System Con

System Con

System Conﬁ

ﬁ

gur

gura

ation

tion

tionExample of System Conﬁ guration

Indica

Indicator

tor

tors

sIndicators

Refer to the separate "IX-DA & IX-BA Operation Manual" for indicators other than those listed.

Light ON

Light OFF

Name Status (Pattern)

Explanation

Status

indicator

Red

ﬂ ashing

Normal ﬂ ashing

0.75 sec 0.75 sec

Booting

Fast ﬂ ashing

0.25 sec 0.25 sec

Device

error

Long interval ﬂ ashing

0.5 sec 4 sec

Communication

failure

Long irregular ﬂ ashing

1 sec 0.25 sec 0.25 sec0.25 sec 0.25 sec 0.25 sec

Firmware

version

upgrading

Short irregular ﬂ ashing

1 sec 0.25 sec0.25 sec 0.25 sec

Initializing

Red

light

Standby

Par

art Names and Accessories

t Names and Accessories

t Names and AccessoriesPart Names and Accessories

LAN

PoE-enabled switch

(third party)

IX Support Tool

(included with IX-MV)

(

third party

)

PoE-enabled switch

(third party)

PoE-enabled switch

(third party)

IX-BAIX-DA

IX-MV Network Video

Recorder

(third party)

Network Camera

(third party)

EMERGENCY

PoE-enabled switch

(third party)

PoE-enabled switch

(third party)

IX-DF-HID*1

IX-DF-P*2

IX-DF

PoE-enabled switch

(third party)

IX-DF-2RA *1

Number of station registrations in address book

Product number Product name

Number of station registrations

in address book

IX-MV Master Station 500 stations

IX-DA, IX-DF, IX-DF-HID-I*1, IX-DF-HID*1,

IX-DF-2RA*1, IX-DF-PI*2, IX-DF-P*2

Video Door Station 20 stations*

IX-BA, IX-SS, IX-SS-2RA*1

Audio Only Door Station

20 stations*3

*1 North America only.

*2 Except North America. HID Card Reader is not included.

*3 Only Master Stations can be registered (Max. 20).

1. Aiphone assumes no responsibility for damages as a result of delayed or unusable services, which were

due to failures in network equipment, communication services by Internet and cellular phone companies, line

interruptions, communication failures, or inaccuracies or omissions in the transmission unit.

2. We will under no conditions be liable for damage that occurs due to the inability to communicate due to

malfunctions, problems, or operational errors in this product.

3. If personal information leaked by eavesdropping or unauthorized access in the communication paths over

the Internet, please be aware that Aiphone assumes no responsibility for the damages.

4. We will under no conditions be liable for any damages or losses resulting from this product’s contents or

speciﬁ cations.

without prior permission from Aiphone Co., Ltd. is strictly forbidden.

6. Please note that this manual may be revised or changed without prior notice.

7. Please note that product speciﬁ cations may be changed for the sake of improvement without prior notice.

8. Please be aware that it is the customer’s responsibility to ensure that their computer is secure. We will under

no conditions be liable for security failures.

9. This system is not intended for life support or crime prevention. It is just a supplementary means of

conveying information. Aiphone will under no conditions be liable for loss of life or property which occurs

while the system is being operated.

10. Keep the unit more than 1m (3.3’) away from radio or TV set.

11. Install the unit in an area that will be accessible for future inspections, repairs, and maintenance.

12. If the unit is down or does not operate properly, unplug the power supply or turn off the POWER switches.

13. If it is used close to a cellular phone, the unit may malfunction.

14. The unit can be damaged if dropped. Handle with care.

15. The unit turns inoperative during power failure.

16. In areas where broadcasting station antennas are close by, the intercom system may be affected by radio

frequency interference.

17. At a gate or porch illuminated by a ﬂ uorescent lamp, the picture may vary, but this is not a malfunction.

18. If stripes or ﬁ ne patterns are reﬂ ected, outlines and colors shown may differ from actual people or

backgrounds, but this is not a malfunction.

19. Warm-color lighting shining on the video door station may change the tint of the picture on the monitor.

20. When using ﬂ uorescent lights to illuminate the screen its colors may periodically change (color rolling), but

this is not a malfunction.

21. The unit case may become a warm with use, but this is not a unit malfunction.

22. Warm air ﬂ owing from inside may interact with the temperature difference in the outside air to cause

condensation to occur on the camera unit. It is recommended that you block the points from which warm air

is ﬂ owing out, such as incoming line ports, in order to prevent condensation.

23. Keep the intercom wires more than 30cm (12’’) away from AC 100-240V wiring. AC induced noise and/or

unit malfunction could result.

24. Door station is weather-resistant, but do not spray high-pressure water. Unit trouble could result.

25. Due to the nature of the camera built into the Video Door Station, external light and the surrounding

environment may affect the projection quality of the TV monitor, so please avoid installing in the following

locations.

Where the background

is white

Where the sky can be seen

in the background

Where direct sunlight

is present

Sky White

wall

Notice

Issue Date : Nov. 2014 FK2122 A P1114 SQ 56142 Printed in Thailand

Installation of Door Station

Mounting frame

Attach the main unit to the mounting frame and put the panel on.

Attach the mounting frame

Verify " UP" is facing up

Do not obstruct.

Drain holes

Low voltage cable

1-gang box

Mounting height

(box center)

IX-DA: 1,500 mm (5')

IX-BA: 1,300 mm (4'3")

Included screws x2

Open the terminal cover and connect the

CAT5e/6 cable and option connector.

Close the terminal cover.

CAT5e/6 cable

Remove the main unit

(loosen the screw)

Special

screwdriver

Knockout section

Remove the panel

Screwdriver

Use a flathead screwdriver to pry

open the panel without scraping it.

Main unit

Included wood

screws x2

Incoming line ports

Please insert the lines from the bottom.

*Make knockouts as necessary.

Mounting height

(device center)

IX-DA: 1,500 mm (5')

IX-BA: 1,300 mm (4'3")

83.5 mm (3-5/16")

Back wiring Surface wiring

Imaging Range and Mounting Location (IX-DA only)

Imaging Position Settings

The camera angle can be adjusted up or down (-8°, 0°, +15°) using the camera angle adjustment lever.

Set it to the optimal level.

Camera angle adjustment lever

+15°

0°

-8°

(Back)

Wall Mounting

The indicated range is a guideline that may change depending on the installation environment.

Unit

center Unit

center

Unit

center

Approx. 1,850 mm (6'1")

Approx. 650 mm (2'2")

500

(20")

500

(20")

500

(20")

Approx. 1,200 mm (3'11")

1,500 mm (5')

Approx. 1,850 mm (6'1")

Approx. 700 mm (2'3")

Approx. 1,150 mm (3'9")

1,300 mm (4'3")

Approx. 1,900 mm (6'3")

Approx. 700 mm (2'3")

150 mm (5")

Approx. 1,200 mm (3'11")

1,500 mm (5')

Camera angle 0° Camera angle +15°

If lower due to a level difference

Horizontal

Vertical Camera angle -8°

Approx. 950 mm (3'1")

500 mm (20")

When light enters the camera, the monitor screen may ﬂ icker brightly or the subject may become dark. Try to prevent strong lighting from entering the

camera directly.

Connection Precautions

Cable

The cable is not included with the product.

CAT5e/6 cable

• Use a straight cable when connecting between equipment.

• Do not use a CAT5e/6 cable with a bending angle of less than a

25 mm (1”) radius. A radius of less than 25 mm (1”) could cause a

communication failure.

CAT5e/6 cableCAT5e/6 cable

Radius ≥ 25 mm (1") Radius < 25 mm (1")

• Do not peel the jacket off the CAT5e/6 cable any more than is

necessary.

• Attach the RJ45 modular plugs using either EIA/TIA-568A or 568B.

Pair4

Pair3

Pair2

Pair1

T568A

Pair4

Pair2

Pair3

Pair1

T568B

1 2 3 4 5 6 7 81 2 3 4 5 6 7 8

• Use the LAN tester to conﬁ rm conduction before connecting the

CAT5e/6 cable.

• The RJ45 connector with cover cannot be connected to CAT5e/6 cable

terminals for Master Station or Door Stations. Use cables without covers

on the connectors.

• Do not pull the CAT5e/6 cable or apply excessive load.

Cable precautions

• Do not use separate conductors or twisted pair cables.

• Do not use an odd number cable.

Wiring Connection

IX-BAIX-DA

Door Station

Green

Purple

Blue

Brown

Red

Orange

Yellow

LAN/PoE

10BASE-T

100BASE-TX

CAT5e/6 straight (UTP)

Relay Output*3

(the electric lock)

Contact Input*1

Shielded wire

ϕ0.8mm(20AWG)-2C

Polarized

PoE-enabled switch

100 m (330')

COM

Audio Output*2

(to paging amplifier)

15 m (50')

Connector

Insulate and secure unused wires.

*1 Contact Input Speciﬁ cations

Input method Form C dry contact (N/O or N/C)

Level detection method

Fixed detection time

200 msec or more

Contact resistance Maximum closure resistance: 700 or lessΩ

Minimum open resistance: 3 k or moreΩ

Terminal short-circuit

current

10 mA or less

Voltage between

the terminals

DC 5V or less (between open terminals)

*2 Audio Output Speciﬁ cations

Output impedance 600 Ω

Output audio level 300 mVrms (600 when terminated)Ω

*3 Relay Output Speciﬁ cations

Output method Form C dry contact (N/O or N/C)

Voltage between

the terminals

AC 24V, 0.5A (resistive load)

DC 24V, 0.5A (resistive load)

Minimum load (AC/DC): 100 mV, 0.1 mA

How to Install

w to Install

w to InstallHow to Install Ho

How to Connect

w to Connect

w to ConnectHow to Connect

There is no space to accommodate the wiring in the back of the

unit. If you do not use a 1-gang box, please provide openings or

handle exposed wiring in other ways.

Product specificaties

Merk:	Aiphone
Categorie:	Intercomsysteem
Model:	IX-BA
Kleur van het product:	Zwart, zilver
Montagewijze:	Opbouw
Merkcompatibiliteit:	Aiphone
Bedrijfstemperatuur (T-T):	-40 - 60 °C
Type product:	Speakermodule