Xiaomi Precision Screwdriver BHR5474GL Handleiding
Xiaomi
Schroefmachine
Precision Screwdriver BHR5474GL
Bekijk gratis de handleiding van Xiaomi Precision Screwdriver BHR5474GL (1 pagina’s), behorend tot de categorie Schroefmachine. Deze gids werd als nuttig beoordeeld door 6 mensen en kreeg gemiddeld 4.8 sterren uit 3.5 reviews. Heb je een vraag over Xiaomi Precision Screwdriver BHR5474GL of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/1
Bit
12
Note: The specications of PH0/PH1/SL2.0/T8H/T10H/H2.0 are C4 × 45 mm, and the
specications of others are C4 × 28 mm.
Bit Specications: C4×28 mm C4×45 mm、
Phillips-head: PH000/PH00/PH0/PH1
Allen: H0.7/H0.9/H1.5/H2.0
Standard: SL1.5/SL2.0
Torx: T2/T3/T4
Torx with a Hole: T5H/T6H/T8H/T9H/T10H
Bit Materials: S2 Steel
Penta: P2/P5
W Shape: W1.5
Y Shape: Y0.6/Y1
Triangular: 2.3
Maximum Torque for I Gear: 0.05 N·m
Maximum Torque for II Gear: 0.2 N·m
Manual Maximum Torque: 3 N·m
Charging Specications: 5 V 0.14 A
Rated Voltage: 3.7 V
Lithium Battery: 350 mAh
Rotation per Minute (Unloaded): 170 rpm
Model: MJDDLSD003QW
Color: Gray
Item Dimensions: 201.8 × 74.2 × 25.2 mm
Net Weight: 353 g
Screwdriver Dimensions: 159 × 16.4 mmΦ
Screwdriver Net Weight: 59 g
Charging Time: 160–200 min
11108
Specications
Troubleshooting
Error
Bit cannot be
installed
Use the C4 bits.Bit size does not match the
size of the bit holder.
Battery cannot
be charged
The USB cable is not
properly plugged in or the
charging voltage is not
suitable.
Check if the charging indicator is
on, properly plug in the USB
cable, and use the specied
charging voltage.
Possible Causes
Solutions
A wrong torque mode
is used.
First set the screwdriver to the
low-torque mode, and then set
it to the high-torque mode if the
force is not enough. Or tighten
or loosen the screw manually.
The screwdriver
does not work
Turn the torque adjustment
knob to the I gear or II gear as
needed, or charge the device.
Bit is covered
with rust
The storage environment
is overly humid.
Store the bits in a dry
environment, and regularly
apply antirust oil on the
surface of the bits.
Screw cannot
be turned or is
stripped
The torque adjustment
knob is turned to gear, or
the lithium battery level is
low.
4
General Power Tool Safety Warnings
5 6
WARNING! Read all safety warnings, instructions, illustrations and specications
provided with this power tool. Failure to follow all instructions listed below may result
in electric shock, re and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power
tool or battery-operated (cordless) power tool.
Keep work area clean and well lit. Cluttered or dark areas invite accidents.
Do not operate power tools in explosive atmospheres, such as in the presence of
ammable liquids, gases or dust. Power tools create sparks which may ignite the dust
or fumes.
Keep children and bystanders away while operating a powertool. Distractions can
cause you to lose control.
Work Area Safety
Power tool plugs must match the outlet. Never modify the plug in any way. Do not
use any adapter plugs with earthed (grounded) power tools. Unmodied plugs and
matching outlets will reduce risk of electric shock.
Avoid body contact with earthed or grounded surfaces, such as pipes, radiators,
ranges and refrigerators. There is an increased risk of electric shock if your body is
earthed or grounded.
Do not expose power tools to rain or wet conditions. Water entering a power tool
will increase the risk of electric shock.
Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock.
Electrical safety
When operating a power tool outdoors, use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
If operating a power tool in a damp location is unavoidable, use a residual current
device (RCD) protected supply.
Use of an RCD reduces the risk of electric shock.
Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use a power tool while you are tired or under the inuence of
drugs, alcohol or medication. A moment of inattention while operating power tools
may result in serious personal injury.
Use personal protective equipment. Always wear eye protection.
Protective
equipment such as a dust mask, non-skid safety shoes, hard hat or hearing
protection used for appropriate conditions will reduce personal injuries.
Prevent unintentional starting. Ensure the switch is in the o-position before
connecting to power source and/or battery pack, picking up or carrying the tool.
Carrying power tools with your nger on the switch or energising power tools that
have the switch on invites accidents.
Remove any adjusting key or wrench before turning the power tool on. A wrench or
a key left attached to a rotating part of the power tool may result in personal injury.
Do not overreach. Keep proper footing and balance at all times. This enables better
control of the power tool in unexpected situations.
Personal Safety
Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing
away from moving parts. Loose clothes, jewellery or long hair can be caught in
moving parts.
If devices are provided for the connection of dust extraction and collection facilities,
ensure these are connected and properly used. Use of dust collection can reduce
dust-related hazards.
Do not let familiarity gained from frequent use of tools allow you to become
complacent and ignore tool safety principles.
A careless action can cause severe
injury within a fraction of a second.
1 2
Product Overview
How to Use
Thank you for using Xiaomi Electric Precision Screwdriver.
Read this manual carefully before use, and retain it for future reference.
1
2
3
4
5
Type-C Charging Port
Torque Adjustment Knob
Charging Indicator
Screw Turning Button
Bit Holder
7
Have your power tool serviced by a qualied repair person using only identical
replacement parts. This will ensure that the safety of the power tool is maintained.
Never service damaged battery packs. Service of battery packs should only be
performed by the manufacturer or authorized service providers.
Service
3
Storage
1
2
3
4
Inner Storage Case
Bit
Screwdriver Handle
Storage Case Shell
The bits in the inner storage case are held in
place by magnetic absorption.
Place the bit in its slot after using it, which will
stick into the slot by itself.
Bit storage
Note: Once being pressed, the inner storage case
will pop up and can easily slide out.
Recharge only with the charger specied by the manufacturer. A charger that is
suitable for one type of battery pack may create a risk of re when used with
another battery pack.
Use power tools only with specically designated battery packs. Use of any other
battery packs may create a risk of injury and re.
When battery pack is not in use, keep it away from other metal objects, like paper
clips, coins, keys, nails, screws or other small metal objects, that can make a
connection from one terminal to another. Shorting the battery terminals together
may cause burns or a re.
Under abusive conditions, liquid may be ejected from the battery; avoid contact. If
contact accidentally occurs, ush with water. If liquid contacts
Battery tool use and care
eyes, additionally seek medical help. Liquid ejected from the battery may cause
irritation or burns.
Do not use a battery pack or tool that is damaged or modied. Damaged or
modied batteries may exhibit unpredictable behavior resulting in re, explosion or
risk of injury.
Do not expose a battery pack or tool to re or excessive temperature.
Exposure to re or temperature above 130°C may cause explosion.
Follow all charging instructions and do not charge the battery pack or tool outside
the temperature range specied in the instructions.
Charging improperly or at
temperatures outside the specied range may damage the battery and increase the
risk of re.
4
5
3
2
1
Press R to tighten the screw.
Press L to loosen the screw.
Screw Turning Button
This screwdriver is equipped with a USB charging cable, and features a
universal Type-C charging port.
Turn the torque adjustment knob to gear to turn
o the screwdriver.
Turn the torque adjustment knob to I gear to set the
screwdriver to the low-torque mode.
Turn the torque adjustment knob to II gear to set
the screwdriver to the high-torque mode.
Torque Adjustment Knob
Take the bit out of the inner storage case, and
insert it into the bit holder.
Installing the bit
When the screwdriver is working and its battery level is
less than 20%, the indicator will quickly blink red for 5
seconds. And the indicator will be o after the button is
released. Please charge the screwdriver immediately.
During charging, the indicator will breathe red.
When the screwdriver is fully charged, the indicator will
turn white.
Indicator status
The screwdriver is held in place by the clip in the inner
storage case. Follow the direction of to take it out.
Press the screwdriver into place after using.
Screwdriver storage
9
Hold the power tool by insulated gripping surfaces, when performing an operation
where the cutting accessory or fasteners may contact hidden wiring. Cutting
accessory contacting a “live” wire may make exposed metal parts of the power tool
“live” and could give the operator an electric shock.
Safety instructions for all operations
Never operate at higher speed than the maximum speed rating of the drill bit. At
higher speeds, the bit is likely to bend if allowed to rotate freely without contacting
the workpiece, resulting in personal injury.
Always start drilling at low speed and with the bit tip in contact with the workpiece.
At higher speeds, the bit is likely to bend if allowed to rotate freely without
contacting the workpiece, resulting in personal injury.
Apply pressure only in direct line with the bit and do not apply excessive pressure.
Bits can bend causing breakage or loss of control, resulting in personal injury.
Safety instructions when using long drill bits
Secure the workpiece.
A workpiece clamped with clamping devices
or in a vice is held more secure than by hand.
Always wait until the power tool has come to a complete stop before placing it
down. The application tool can jam and cause you to lose control of the power tool.
Switch the power tool o immediately if the application tool becomes blocked. Be
prepared for high torque reactions which cause kickback. The application tool
becomes blocked when it becomes jammed in the workpiece or when the power
tool becomes overloaded.
Use suitable detectors to determine if there are hidden supply lines or contact the
local utility company for assistance. Contact with electric cables can cause re and
electrical shock. Damaging gas lines can lead to explosion. Breaking water pipes causes
property damage.
Additional safety information
13
All products bearing this symbol are waste electrical and electronic equipment
(WEEE as in directive 2012/19/EU) which should not be mixed with unsorted
household waste. Instead, you should protect human health and the
environment by handing over your waste equipment to a designated collection point for
the recycling of waste electrical and electronic equipment, appointed by the
government or local authorities. Correct disposal and recycling will help prevent
potential negative consequences to the environment and human health. Please
contact the installer or local authorities for more information about the location as
well as terms and conditions of such collection points.
We Shanghai HOTO Technology Co., Ltd., hereby, declares that this
equipment is in compliance with the applicable Directives and European Norms,
and amendments. The full text of the EU declaration of conformity is available at the
following internet address:
http://www.mi.com/global/service/support/declaration.html
This supplier’s declaration of conformity is hereby for
Responsible Party – U.S. Contact Information
Representative of Responsible Party for SDoC
We declare that the above mentioned device has been tested
and found in compliance with CFR 47 Part 15 Regulation.
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Product: Xiaomi Electric Precision Screwdriver
Model Number(s): MJDDLSD003QW
Brand/Trade: Xiaomi
Company: TEKMOVIL LLC
Address: 601 BRICKELL KEY DR #723 Miami, FL 33131
Country: U.S.A.
Telephone No.: +1(312)282-5246
Internet contact information: kim.peterson@tekmovil.com
Company: Shanghai HOTO Technology Co., Ltd.
Address: Building 45, No.50 Moganshan Road, Putuo District, Shanghai, China
Country: China
Telephone No.: 400-021-8696
Federal Communications Commission Supplier’s
Declaration of Conformity
14
4
1
3
2
Keep the bit stay here for
5 seconds to complete
the magnetization.
Press the inner storage case from the top to open
it.
Press the inner storage case from the top again
to close it.
Opening and closing the storage case
Do not force the power tool. Use the correct power tool for your application. The
correct power tool will do the job better and safer at the rate for which it was
designed.
Do not use the power tool if the switch does not turn it on and o. Any power tool
that cannot be controlled with the switch is dangerous and must be repaired.
Disconnect the plug from the power source and/or remove the battery pack, if
detachable, from the power tool before making any adjustments, changing
accessories, or storing power tools.
Such preventive safety measures reduce the
risk of starting the power tool accidentally.
Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
Power Tool Use And Care
Maintain power tools and accessories. Check for misalignment or binding of
moving parts, breakage of parts and any other condition that may aect the power
tool's operation. If damaged, have the power tool repaired before use. Many
accidents are caused by poorly maintained power tools.
Use the power tool, accessories and tool bits etc. in accordance with these
instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for operations dierent from those intended
could result in a hazardous situation.
Keep handles and grasping surfaces dry, clean and free from oil and grease.
Slippery handles and grasping surfaces do not allow for safe handling and control of
the tool in unexpected situations.
Hold the power tool securely. When tightening and loosening screws be prepared for
temporarily high torque reactions.
In case of damage and improper use of the battery, vapours may be emitted. The
battery can set alight or explode. Ensure the area is well ventilated and seek medical
attention should you experience any adverse eects. The vapours may irritate the
respiratory system.
Do not open the battery. There is a risk of short-circuiting.
The battery can be damaged by pointed objects such as nails or screwdrivers or by
force applied externally. An internal short circuit may occur, causing the battery to
burn, smoke, explode or overheat.
Only use the battery with products from the manufacturer. This is the only way in
which you can protect the battery against dangerous overload.
Protect the battery against heat, e.g. against continuous intense sunlight, re, dirt,
water and moisture. There is a risk of explosion and short-circuiting.
Power Adapter Output: 5V 0.14A Max.
Ambient Temperature while Charging: 0 to 45°C
Manufactured for: Xiaomi Communications Co., Ltd.
Manufactured by: Shanghai HOTO Technology Co., Ltd.
(a Mi Ecosystem company)
Address: Building 45, No.50 Moganshan Road, Putuo District, Shanghai, China
For further information, please go to www.mi.com
User Manual Version: V1.0
Product specificaties
| Merk: | Xiaomi |
| Categorie: | Schroefmachine |
| Model: | Precision Screwdriver BHR5474GL |
Heb je hulp nodig?
Als je hulp nodig hebt met Xiaomi Precision Screwdriver BHR5474GL stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Schroefmachine Xiaomi
Handleiding Schroefmachine
- Omega
- Chamberlain
- Fuxtec
- Ingersoll Rand
- Graphite
- Metabo
- Dedra
- Festool
- Bavaria
- Bruder Mannesmann
- NEO Tools
- Tacklife
- Bosch
- Draper
- Cotech
Nieuwste handleidingen voor Schroefmachine
15 Juni 2025
15 Juni 2025
15 Juni 2025
11 Juni 2025
8 Juni 2025
8 Juni 2025
8 Juni 2025
7 Juni 2025
7 Juni 2025
7 Juni 2025