Wolf MGK-130 Handleiding

Wolf Verwarmingsketel MGK-130

Bekijk gratis de handleiding van Wolf MGK-130 (52 pagina’s), behorend tot de categorie Verwarmingsketel. Deze gids werd als nuttig beoordeeld door 90 mensen en kreeg gemiddeld 4.7 sterren uit 7 reviews. Heb je een vraag over Wolf MGK-130 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

PDF downloaden (8.4 MB)

Pagina 1/52

Assembly and

operating instructions

Gas condensing boilers

MGK-130

MGK-170

MGK-210

MGK-250

MGK-300

Document no. 3062880_201305Subjecttotechnicalmodications

These installation instructions are to be retained by the user.

We cannot accept any warranty claims if these operating instructions have not been

observed.

Wolf GmbH · Postfach 1380 · D-84048 Mainburg · Tel. +49-8751/74-0 · Fax +49-8751/741600 · Internet: www.wolf-heiztechnik.de

Beoordeel deze handleiding

4.7/5 (7 Beoordelingen)

Product specificaties

Merk:	Wolf
Categorie:	Verwarmingsketel
Model:	MGK-130

Foutcodes Wolf MGK-130

Foutcodes uit de officiële handleiding, met betekenis en oplossing.

Code	Betekenis	Oplossing
1	TBV excess temperature, water pressure too low, fault condensate pump	Check the system pressure. Check the heating circuit pump. Vent the system. Press the reset button. Check the condensate pump. Increase system pressure
11	Flame pretence	Press the reset button
12	Faulty flow sensor, gas pressure too low	Check lead. Check the flow sensor. Check gas pressure. Check the gas pressure switch settings
14	Cylinder sensor faulty	Check sensor and lead
15	Outside temperature sensor faulty	Check lead. Check the outside temperature sensor
16	Return sensor faulty	Check lead. Replace the return sensor
20	Fault, gas valve "1"	Replace the gas combination valve
21	Fault, gas valve "2"	Replace the gas combination valve
24	Gas fan fault	Check the gas fan supply cable and the gas fan; press the reset button
25	Gas fan fault	Check the gas fan supply cable and the gas fan; press the reset button
26	Gas fan fault	Check the gas fan supply cable and the gas fan; press the reset button
30	CRC fault, gas condensing boiler	Switch the power supply OFF and ON. If unsuccessful, replace the control PCB
31	CRC fault burner	Switch the power supply OFF and ON. If unsuccessful, replace the control PCB
32	24VAC supply faulty	Check the gas fan
33	CRC fault; default values	Replace the control PCB
34	CRC error BCC	Exchange parameter plug
35	BCC missing	Plug in the correct parameter plug
36	CRC error BCC	Exchange parameter plug
37	Wrong BCC	Plug in the correct parameter plug
38	BCC no. invalid	Exchange parameter plug
39	BCC system error	Exchange parameter plug
4	No flame builds	Check the gas supply line and open the gas valve, if necessary. Check the ignition electrode and ignition cable. Press reset
41	Flow monitoring	Vent the heating system, check the system pressure. Check the heating circuit pump
43	Burner starts >20 per hour	Check the flow rate; Header sensor must measure the common feed temperature of the cascade
5	Flame failure during operation	Check CO values. Check ionisation electrode and cable. Press the reset button
50	Activation of the parameter plug	Press the reset button twice
52	Activation of the parameter plug	Press the reset button twice
6	TW excess temperature	Check the system pressure. Vent the system. Increase pump speed
60	Ionisation current fluctuates	Clean siphon, check flue gas system, check ventilation air, check monitoring electrode
61	Ionisation current fails	Check monitoring electrode and lead
7	TBA excess temperature, overpressure in the flue gas system	Clean the heat exchanger, check the flue gas system. Check ventilation air system. Check flue gas pressure switch