Winix Zero 5520 Handleiding

Bekijk gratis de handleiding van Winix Zero 5520 (2 pagina’s), behorend tot de categorie Luchtreiniger. Deze gids werd als nuttig beoordeeld door 2 mensen en kreeg gemiddeld 4.8 sterren uit 9 reviews. Heb je een vraag over Winix Zero 5520 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

When to Replace Filters

FilterIndicator LightWhen to ServiceWhen to Replace

Pre-FilternonePermanentClean once every 14 days

AOC™ Carbon Filter

Can NOT be WASHED

Lasts up to

12months

True HEPA Filter

•When the Check Filter Indicator LED is on, it is time to replace the True HEPA Filter and

AOC™Carbon Filter.

•Intervals between filter replacement may vary depending on environment.

MAINTENANCE

INITIAL OPERATION

REPLACING FILTERS

GF



Resetting Filter Life:

After replacing your True HEPA Filter, place the Pre-Filter back in and close the Front

Panel. While the unit is on, hold the Filter Reset Button for at least 5 seconds until you

hear the beep. After the beep, the Filter Replacement Indicator will disappear. Your

Winix True HEPA is now reset.

1.

Remove the front panel by grasping its upper

edge and gently pulling forward.

2.

Remove the Pre-Filter, then the bag of filters

behind it.

3.

Remove filters from protective plastic bag.

4.

Install the filters until they fit securely in place.

03. True HEPA Filter (back)

02. AOC™ Carbon Filter (middle)

01. Pre-Filter (front)

5.

After filters are installed, close the front panel.

6.

Insert the power cord into an electrical outlet.

Latch

0302

01

Latch

FRONTBACK

PACKAGE CONTENTS

Air Outlet

Vent

Handle

Power Plug

Control Panel

Front Panel

Unit

(1) Pre-Filter

(1) AOC™ Carbon Filter

(1) True HEPA Filter

User

Manual

Wi-Fi Setup

Guide

WHERE TO USE

MODEL PART DIAGRAM

30~45cm30~45cm

Allow 30~45cm. of space between TVs, radios, and

other electronics. Electromagnetic interference from

certain electronics may cause product malfunction.

Place indoors away from direct sunlight. Direct

exposure may cause product malfunction or failure.

Only place on hard, flat surfaces. Flimsy or slanted

surfaces may result in abnormal noise and vibrations.

Allow at least 30~45cm. from walls for maximum air flow

4-STAGE AIR PURIFICATION

Air Purification means it

removes inanimate particles

CLEANING CARE

NOTICE

• When cleaning the unit, always unplug the power cord

first and then wait until the unit has cooled down.

• Never disassemble, repair, or modify this unit yourself.

• Do not use flammable sprays or liquid detergents.

• Do not allow children to clean or maintain the unit.

• Before cleaning or maintaining, ensure unit is

unplugged.

• Do not use benzene, alcohol, or other volatile fluids,

which may cause damage or discoloration

.

SPECIFICATIONS

Model5520(AU)

VoltageAC 220 V - 240 V, 50 / 60 Hz

Power Rate65 W

Verified

Room Size

99m

2

Dimensions

345 mm (W) x 210 mm (D)

x 563 mm (H)

Weight6 kg

Filter SKUFilter GF : 1712-0123-03

Exterior design, and product specifications may be changed

without prior notice to improve product performance.

AUSCLIMATE FILTER CLUB

For exclusive savings

on replacement filters

AUSTRALIANEW ZEALAND

New Zealand

PO Box 100707

North Shore Mail Centre

Auckland 0745

www.cdbgroup.com

Australia

PO Box 574

South Morang

Victoria 3752

www.cdbgroup.com

01. Auto Indicator

Indicates whether Auto Mode is enabled or disabled.

02. Sleep Indicator

Indicates whether Sleep Mode is enabled or

disabled.

03. PlasmaWave

®

Indicator

Indicates whether PlasmaWave

®

is enabled or

disabled.

04. Fan Speed Indicator

Indicates the current fan speed.

05. Light Sensor

Detects the amount of ambient light in the

environment.

06. Wi-Fi / Pairing Button

•A quick press will turn Wi-Fi on/off.

•A long press of 3 seconds will activate pairing

mode.

•A Wi-Fi indicator will display on the front while

Wi-Fi is active.

07. Power Button

Turns the unit on or off.

During the first 30 seconds of powering up, the Air

Quality Indicator will cycle through Blue, Amber and

Red colors. Smart Sensor takes approximately 4

minutes to detect the air quality in the environment

before normal operation begins.

08. PlasmaWave

®

Button

Enables or disables PlasmaWave

®

.

When the unit is running, you may hear a chirping

or buzzing sound. The sound is from large particles

passing through PlasmaWave

®

, it is normal and

does not signify product failure.

Press the PlasmaWave

®

button when the unit is on

to enable or disable this feature.

CONTROL PANEL

09. Wi-Fi Indicator

Indicates whether Wi-Fi Mode is enabled or

disabled.

10. Fan Speed Button

Enables manual operation of the unit's fan speeds.

•Press to cycle through and set the desired fan

speed (Low, Medium, High, Turbo).

•Auto Mode:

-Auto Mode automatically adjusts fan speeds

according to your indoor air quality. The fan

speed will adjust to low when air quality is

good, medium when fair, and to high when

poor.

•Sleep Mode:

-When Sleep Mode is activated, the Air Quality

Indicator LED light is disabled.

-Fan speed will automatically set to minimum

speed (lower than 'Low') which will be nearly

silent.

-When Sleep Mode is active, PlasmaWave

®

will be disabled, but it can be turned back on.

11. Filter Reset Button

After replacing the True HEPA Filter, press the

Filter Reset button for at least 5 seconds until the

Filter Replacement Indicator turns off.

12. Filter Reset Indicator

LED light indicates when it is time to change the

filter.

02

0903

041201

071006080511

3

True HEPA Filter

2

AOC™ Carbon Filter

4

PlasmaWave

®

TechnologyPre-Filter

1

Cleaning the Exterior & Interior:

Wipe with a soft damp cloth using room

temperature water.

•Afterwards, wipe it down with a dry cloth.

Open the front panel and clean the interior

with a vacuum cleaner.

•For optimal performance, clean every

1-2months.

Cleaning the Filters:

Use a vacuum cleaner or soft brush to

clean the Pre-Filter.

•If it is excessively soiled, rinse in room

temperature water. Do not use detergent or

soap.

Allow the filter to dry for 24 hours or

more before using.

Intervals between filter

cleaning may vary depending on the air

quality. Do not use hot water over 40

o

C or

volatile fluids such as paint thinner.

Product specificaties