Wavtech link6 Handleiding

Wavtech Audio/video-converter link6

Lees hieronder de 📖 handleiding in het Nederlandse voor Wavtech link6 (10 pagina's) in de categorie Audio/video-converter. Deze handleiding was nuttig voor 56 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/10
www.wavtech-usa.com
Owner’s Manual
6-Channel Line Output Converter
Summing ŸAUX Input ŸMulti-Function Remote
• Any function that requires your prolonged attention should not be performed DO NOT DRIVE WHILE DISTRACTED.
while driving. Always stop the vehicle in a safe location before performing any such function. Failure to do so may
result in an accident.
• KEEP THE VOLUME AT MODERATE LEVELS WHILE DRIVING. Excess volume levels can obscure sounds such as
emergency vehicle sirens or road warning signals and may result in an accident. Continuous exposure to high sound
pressure levels may cause permanent hearing loss. Use common sense and practice safe sound.
• FOR USE WITH 12V NEGATIVE GROUND VEHICLE APPLICATIONS ONLY. Using this product other than in its
designed application may result in fire, injury or product damage.
•MAKE THE CORRECT WIRING CONNECTIONS AND USE PROPER FUSE PROTECTION. Failure to connect wiring
correctly or use appropriate fuse protection may result in fire, injury or product damage . Ensure proper fusing of all
system power wiring and install a 1-ampere in-line fuse (not included) with the +12V lead to the unit’s power supply
connector.
• DISCONNECT THE NEGATIVE BATTERY TERMINAL BEFORE INSTALLATION. Failure to do so may result in fire,
injury or damage to the unit.
• D O NOT ALLOW CABLES TO BECOME ENTANGLED IN SURROUNDING OBJECTS. Arrange wiring and cables to
prevent obstructions when driving. Cables or wiring that obstruct or hang up on places such as steering wheel, brake
pedals, etc. can be extremely hazardous.
• DO NOT DAMAGE VEHICLE SYSTEMS OR WIRING WHEN DRILLING HOLES. When drilling holes in the chassis for
installation, take precautions so as not to contact, puncture or obstruct brake lines, fuel lines, fuel tanks, electrical
wiring, etc. Failure to take such precautions may result in fire or an accident.
• DO NOT UTILIZE OR CONNECT TO ANY PART OF VEHICLE SAFETY SYSTEMS. Bolts, nuts or wires used in the
brake, airbag, steering or any other safety-related systems or fuel tanks should NEVER be used for mounting, power or
ground connections. Using such parts may disable control of the vehicle or result in fire.
WARNING
WARNING This symbol means important instructions.
Failure to heed them can result in serious injury or death.
CAUTION This symbol means important instructions.
Failure to heed them can result in injury or property damages.
• STOP USE IMMEDIATELY IF A PROBLEM OCCURS. Failure to do so may result in personal injury or damage to the
product. Return it to your authorized Wāvtech dealer.
• HAVE AN EXPERT DO THE WIRING AND INSTALLATION. This unit requires special technical skill and experience for
wiring and installation. To insure safety and proper function, always contact the authorized dealer where you
purchased the product to have it done professionally.
• INSTALL THE UNIT SECURELY WITH SPECIFIED PARTS. Be sure to use only the included parts and specified
installation accessories (not included). Use of other than designated parts may damage this unit. Install the unit
securely so that it will not come loose during a collision or sudden jolt.
• ROUTE WIRING AWAY FROM SHARP EDGES AND MOVING PARTS. Arrange cables and wiring away from sharp or
pointed edges and avoid moving parts such as seat hinges or rails to prevent pinching or wear. Use loom protection
where appropriate and always use a grommet for any wiring routed through metal.
• NEVER RUN SYSTEM WIRING OUTSIDE OR UNDERNEATH THE VEHICLE. All wiring must be routed, secured and
protected inside the vehicle. Failure to do so may result in fire, injury or property damage.
• INSTALL THE UNIT IN A DRY AND VENTILATED LOCATION. Avoid mounting locations where the unit will likely be
exposed to high moisture or heat without adequate ventilation. Moisture penetration or heat buildup may result in
product failure.
• REDUCE GAIN AND SOURCE VOLUME TO MINIMUM LEVELS FOR INITIAL SYSTEM TUNING AND BEFORE
CONNECTION TO AN AMPLIFIER. Ensure amplifier power is off before connecting RCA cables and follow proper
system gain setting procedures. Failure to do so may result in damage to the amplifier and/or connected components.
CAUTION
Package Contents:
Main Unit Terminals
Accessories Required for
Installation :(not included)
Mounting Tabs
(detachable)
ŸRCA Interconnects
Ÿ18AWG Wire
ŸIn-line Fuse Holder w/1A fuse
ŸBattery Ring Terminal
ŸWire Crimp Connectors
ŸGrommets and Loom
ŸCable Ties
ŸMounting Screws
1
Multi-Function Remote
Remote Cable
(16.4ft / 5m)
PWR/SPK GND
Introduction
Welcome to Wāvtech, exceptional mobile audio integration products for audiophiles. Our products are
engineered to provide a truly remarkable listening experience. Built for the professional installer, our
OEM integration and signal processor models are simply the best solution available for unlimited sound
system upgrades while retaining the factory receiver.
ΠPower Indicator: This red LED indicates
when the link6 is powered on. Once
illuminated, there will be a short delay
before audio signal output is enabled.
During initial power connection, the
LED may illuminate for a brief period.
Auto Turn-On Detect Jumpers: By
default, the link6 is set to detect
both DC-offset and audio signal for
turning itself on/off automatically.
These jumpers allow either mode to
be independently defeated for cases
where only one turn-on mode is
preferred or to bypass both modes
when a switched +12V trigger is available and connected to the REM IN terminal.
ŽPower Supply Terminal: For +12V battery, chassis ground, remote input and remote output wire
connections. A minimum of 18AWG wire is recommended for power and ground connections. Always
protect the +12V power wire with a 1-amp fuse.
Speaker Level Input Terminals: For up to six channels of speaker level input connections to the source.
Input signals ranging from 2Vrms to 20Vrms will produce up to 10Vrms RCA output from maximum to
minimum gain. For factory amplifiers with more than 20Vrms signal or if the link6’s output is too high
for the connected aftermarket amplifier(s) with all gains at minimum, internal jumpers are available to
reduce the input sensitivity range by half (-6dB) for 4Vrms up to 40Vrms.
Auxiliary Input Jack: This 3.5mm stereo AUX input is for the connection of a portable device such as a
smartphone or MP3 player, but may also be used for other low level (a.k.a line level) sources using a
3.5mm adapter. AUX may be selected as a separate source via the multi-function remote, or
programmed as the primary source for stand-alone systems where the speaker level inputs are not
used (see pg4). Input signals ranging from 0.5Vrms to 5Vrms will produce up to 10Vrms RCA output at
maximum to minimum gain setting. This input is differential but may be set to unbalanced via internal
jumpers (labeled BAL/UNBAL) if required for a particular source.
‘CH1/2 Output Select: This switch allows CH1/2’s output to be selected between 1/2 for direct input
pass-through (default) or 5/6 to copy signal from CH5/6 internally after its summing stage. The latter
is particularly useful when summing 3-way systems for retaining remote level control over CH5/6
while also providing a separate summed full-range output from CH1/2.
’RCA Output Jacks: These six channels of RCA outputs are for signal connection to your s
amplifier(s). For a speaker level source, output from CH3/4 and CH5/6 will depend upon their
respective INPUT CH settings (see pg3), while CH1/2 is set by its output select switch (see above). ‘
For an AUX source, left/right stereo signals will be routed to all output pairs. Use quality
interconnects to ensure stable connections and minimize the possibility for induced noise.
“Remote Level Control Jack: This RJ45 jack is for connecting the multi-function remote to the main
unit with the supplied cable. A standard ethernet cable may also be used.
”Mounting Tabs: These mounting tabs are for securing the link6 during installation with screws or
cable ties. They are removable if the unit can be safely secured by another method.
Connections & Functions
Ÿ 6-Channel Line Output Converter
Ÿ6-Channel Summing Processor
ŸMulti-Function Remote
Master Volume
AUX Volume
Independent CH5/6 Level
Source/Function Select
ŸAUX 3.5mm Input
ŸDifferential Balanced Inputs
Ÿ Low Impedance Outputs
2
ŸVariable Gain Adjustments w/Clip LEDs
Ÿ2/4/6-Channel Input Select
Ÿ2/3-Way Summing w/Retained CH5/6 Level Control
ŸNever-Zero CH5/6 Output with Front & Rear Inputs
ŸSelectable DC-Offset and/or Audio Detect Auto Turn-On
ŸGenerated +12V Remote Output
ŸOEM Load Detect Compatible
ŸLocking Detachable Power/Speaker Terminals
ŸPanel Mount RCA Jacks
ŸCompact Aluminum Chassis w/Detachable Mounting Tabs
Features
’
“
”
‘
Œ
Ž

Product specificaties

Merk: Wavtech
Categorie: Audio/video-converter
Model: link6

Heb je hulp nodig?

Als je hulp nodig hebt met Wavtech link6 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Audio/video-converter Wavtech

Wavtech

Wavtech bassFREQ Handleiding

31 Oktober 2023
Wavtech

Wavtech LinkD Handleiding

31 Oktober 2023
Wavtech

Wavtech Link4 Handleiding

31 Oktober 2023
Wavtech

Wavtech Link8 Handleiding

31 Oktober 2023
Wavtech

Wavtech link2 Handleiding

31 Oktober 2023
Wavtech

Wavtech linkDQ Handleiding

31 Oktober 2023
Wavtech

Wavtech link6 Handleiding

31 Oktober 2023
Wavtech

Wavtech bassRESTOR Handleiding

31 Oktober 2023
Wavtech

Wavtech LinkT Handleiding

31 Oktober 2023
Wavtech

Wavtech linkQ Handleiding

31 Oktober 2023

Handleiding Audio/video-converter

Nieuwste handleidingen voor Audio/video-converter

Audison

Audison Bit Ten D Handleiding

21 April 2024
Spatz

Spatz OPTO-RCA Handleiding

20 April 2024
Spatz

Spatz RCA-OPTO Handleiding

20 April 2024
PTN-electronics

PTN-electronics CHH2 Handleiding

9 April 2024
Adder

Adder -DVA Handleiding

8 April 2024
GEM

GEM CX1003 Handleiding

29 Maart 2024
Audiotec Fischer

Audiotec Fischer Helix DSP.3S Handleiding

25 Maart 2024
Audiotec Fischer

Audiotec Fischer DSP MINI Handleiding

25 Maart 2024
Smart-AVI

Smart-AVI CVH-01S Handleiding

13 Maart 2024
SIIG

SIIG CE-CV0011-S1 Handleiding

13 Maart 2024