VTech BM2700 Handleiding

VTech Babyfoon BM2700

Lees hieronder de 📖 handleiding in het Nederlandse voor VTech BM2700 (2 pagina's) in de categorie Babyfoon. Deze handleiding was nuttig voor 26 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
Congratulations
on purchasing your new VTech product. Before
using this product, please read Important safety
instructions.
This manual has all the feature operations and
troubleshooting necessary to install and operate
your new VTech product. Please review this
manual thoroughly to ensure proper installation
and operation of this innovative and feature rich
VTech product.
What’s in the box
Important safety instructions
When using your equipment, basic safety precautions
should always be followed to reduce the risk of re,
electric shock and injury, including the following:
1. Follow all warnings and instructions marked on the
product.
2. Adult setup is required.
3. This product is intended as an aid. It is not a
substitute for responsible and proper adult
supervision and should not be used as such.
4. This product is not intended for use as a medical
monitor.
5. Do not use this product near water. For example,
do not use it next to a bath tub, wash bowl,
kitchen sink, laundry tub or swimming pool, or in a
wet basement or shower.
6. CAUTION: Use only the batteries provided. There
may be a risk of explosion if a wrong type of
battery is used for the parent unit. Do not dispose
of batteries in a re. They may explode.
7. Use only the adapters included with this product.
Incorrect adapter polarity or voltage can seriously
damage the product.
Baby unit power adapter: Output: 6V DC 400mA
Parent unit power adapter: Output: 6V DC 400mA.
8. The power adapters are intended to be correctly
oriented in a vertical or floor mount position. The
prongs are not designed to hold the plug in place
if it is plugged into a ceiling, under-the-table or
cabinet outlet.
9. For pluggable equipment, the socket-outlet shall
be installed near the equipment and shall be easily
accessible.
10. Unplug this product from the wall outlet before
cleaning. Do not use liquid or aerosol cleaners.
Use a damp cloth for cleaning.
11. Unplug the power cords before replacing
batteries.
12. Do not cut off the power adapters to replace
them with other plugs, as this causes a hazardous
situation.
13. Do not allow anything to rest on the power cords.
Do not install this product where the cords may be
walked on or crimped.
14. This product should be operated only from the
type of power source indicated on the marking
label. If you are not sure of the type of power
supply in your home, consult your dealer or local
power company.
15. Do not overload wall outlets or use an extension
cord.
16. Do not place this product on an unstable table,
shelf, stand or other unstable surfaces.
17. This product should not be placed in any area
where proper ventilation is not provided. Slots and
openings in the back or bottom of this product
are provided for ventilation. To protect them from
overheating, these openings must not be blocked
by placing the product on a soft surface such as
a bed, sofa or rug. This product should never be
placed near or over a radiator or heat register.
18. Never push objects of any kind into this product
through the slots because they may touch
dangerous voltage points or create a short circuit.
Never spill liquid of any kind on the product.
19. To reduce the risk of electric shock, do not
disassemble this product, but take it to
an authorized service facility. Opening or
removing parts of the product other than
specied access doors may expose you to
dangerous voltages or other risks. Incorrect
reassembling can cause electric shock when the
product is subsequently used.
20. You should test the sound reception every
time you turn on the units or move one of the
components.
21. Periodically examine all components for damage.
22. Be aware of possible loss of privacy while using
public airwaves. Conversations may be picked
up by other nursery monitors, cordless phones,
scanners, etc.
23. Children should be supervised to ensure that they
do not play with the product.
24. The product is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
SAVE THESE INSTRUCTIONS
Cautions
1. Use and store the product at a temperature
between 0oC and 40oC.
2. Do not expose the product to extreme cold, heat
or direct sunlight. Do not put the product close to
a heating source.
3. Batteries should not be exposed to excessive heat
such as bright sunshine or re.
4. —Strangulation Hazard—Children Warning
have STRANGLED in cords. Keep this cord out
of the reach of children (more than 1 metre
away).
5. Never place the baby unit inside the baby’s cot or
playpen. Never cover the baby unit or parent unit
with anything such as a towel or a blanket.
6. Other electronic products may cause
interference with your baby monitor. Try
installing your baby monitor as far away
from these electronic devices as possible:
wireless routers, radios, cellular telephones,
intercoms, room monitors, televisions, personal
computers, kitchen appliances and cordless
telephones.
Connect and charge the
battery
NOTE
S
• The rechargeable battery is pre-installed in your
parent unit.
• Use only the power adapters supplied with this
product.
• Make sure the electrical outlets are not controlled by
wall switches.
• The power adapters are intended to be correctly
oriented in a vertical or floor mount position. The
prongs are not designed to hold the plug in place if
they are plugged into a ceiling, under-the-table or
cabinet outlet.
• Make sure the parent unit, the baby unit and the
power adapter cords are out of reach of children.
Connect the baby monitor
Charge the parent unit battery
When you have connected and turned on
the parent unit, the battery will be charged
automatically. The battery icon indicates the
battery status (see the following table).
NOTE
S
• The parent unit battery is fully charged after
11 hours of continuous charging.
• It takes longer to charge the battery when the
parent unit is turned on. To shorten the charging
time, turn the parent unit off while charging.
• The standby time varies depending on the volume
level you set and your actual use.
Battery
indicators
Battery status Action
The screen
displays
Battery low
at Parent
Unit. The
or light
flashes.
The battery
has very little
charge and
may be used
for only a
short time.
Charge
without
interruption
(about 30
minutes).
The battery
icon
becomes
solid .
The battery is
fully charged.
To keep
the battery
charged,
connect it to
AC power
when not in
use.
Before use
NOTE
• This baby monitor is intended as an aid. It is not a
substitute for proper adult supervision, and should
not be used as such.
Test your baby monitor
You may test the baby monitor before initial use,
and at regular times thereafter.
CAUTION
• For hearing protection, make sure the
parent unit is more than 1 metre away from
the baby unit . If you hear any high-pitched
noise, move the parent unit further until the
noise stops. You can also press on the VOL
parent unit to lower or mute the noise.
1. Make sure your baby unit and parent unit are
on.
2. The parent unit displays images from the
baby unit.
• Speak towards the microphone of the
baby unit. You will hear the sound at the
parent unit.
NOTE
• When the parent unit displays , No link to Camera
and the LED light flashes, move the parent POWER
unit closer to the baby units (observe the minimum
distance of 1 metre). You can also check if the
baby unit is connected to a live power socket and
switched on.
TIP
• Increase the speaker volume of the parent unit if
you cannot hear the sounds transmitted from the
baby units.
Positioning the baby monitor
CAUTION
• Keep the baby unit out of the reach of baby. your
Never place or mount the baby unit inside the
baby’s or playpen.cot
NOTE
• To avoid interference from other electronic devices,
place your baby monitor far away from devices such
as wireless routers, microwaves,
cell phones and computers.
1. Place the baby unit more than 1 metre away
from your baby.
2. Adjust the angle of the baby unit camera to
aim at your baby.
3. Place the parent unit more than 1 metre away
from the baby unit.
• The default volume of your parent unit is level
3, and the maximum volume is level 5. If you
experience high-pitched screeching noise from
your baby monitor while positioning:
- Make sure your baby unit and parent unit are
more than 1 metre apart, OR
- Turn down the volume of your parent unit.
Mount the baby monitor
(optional)
You will need to purchase the following
items separately to mount your baby unit:
2 screws
2 anchors
Operating range
The operating range of the baby monitor is up
to outdoors or 50 metres indoors. 300 metres
The actual operating range may vary depending
on the environmental conditions and other
interferences such as walls, doors and other
obstructions.
Overview
Baby unit overview
1PAIR button
• Your baby unit and parent unit
provided are already paired.
2POWER LED light
• On when the baby unit is turned on
and is paired to the parent unit.
• Flashes when the baby unit is not
being viewed; or when the link to the
parent unit is lost.
3Microphone
4Camera
5Infrared LEDs
6Light sensor
7 ON/OFF switch
• Slide to turn on or off the baby unit.
8Speaker
9Power jack
10 Wall mount holes
Parent unit overview
1 POWER LED light
• Green when the parent is powered on.
• Flashes green when no link to camera.
2TALK
• Press and hold to talk to the baby unit.
3MENU/SELECT
• Press to enter the menu.
• While in a menu, press to choose an
item, or save a setting.
4Arrow keys and VOL / VOL
VOL /
• Press to increase the parent unit
speaker volume.
• While in a menu, press to scroll up, or
to enter an item’s sub-menu.
• While zooming, press and hold to
move the zoomed image upward
VOL /
• Press to decrease the parent unit
speaker volume.
• While in a submenu, press to scroll
down.
• While zooming, press and hold to
move the zoomed image downward.
• While in a menu, press to choose the
next item on the left.
• While zooming, press and hold to
move the zoomed image leftward.
• While in a menu, press to choose the
next item on the right.
• While zooming, press and hold to
move the zoomed image rightward.
5Microphone
6Battery indicator
• Red when battery is charging.
• Flashes red when battery is low.
7Visual sound indicators
The visual sound indicators can show the
sound level detected by the baby unit.
Sound level detected by the baby unit
•
One to three green lights indicate a
moderate sound level detected by the
baby unit.
•
Additional red lights indicate a higher
sound level detected by the baby unit
(e.g. baby crying loudly).
8 Zoom / Back
• Press to zoom in or out.
• Press to return to the previous screen.
9LCD display
10 Speaker
11 Stand
12 ON/OFF switch
• Slide to turn on or off the parent unit.
13 Power jack
Parent unit status icons
Connection status
• or displays when
strong signal strength is
detected between the baby unit
and the parent unit.
• or or displays when
moderate or low signal strength
is detected between the baby
unit and the parent unit.
• displays when the link
between the baby unit and the
parent unit is lost.
Current view status
• Displays camera when baby unit
successfully linked to parent unit.
Zoom
• Displays when the current image
on the parent unit has zoomed
in.
Night vision
• Displays when the baby unit
being viewed has activated the
night vision feature.
Mute alert
• Displays when the parent unit
speaker volume is set to off.
or
Real-time temperature
• Displays the real-time
temperature detected by the
baby unit in Fahrenheit (oF) or
Celsius (oC) (e.g. 57
oF or 14
oC).
Battery status
• animates
when the battery is charging.
• displays solid when the
battery is fully charged.
• displays when the battery is
low and needs charging.
Speaker volume
• Displays the parent unit speaker
volume level while adjusting.
User’s manual
BM2700
Full Colour Video &
Audio Monitor
For product support please call:
1300 369 193
10
1
3
4
5
2
6
8
9
7
Use a pencil to mark two holes in
parallel. Make sure they are the same
distance apart as the wall mount holes
on the baby unit.
NOTE
Check for reception strength and camera
angle before drilling the holes.
•
Drill two holes in the wall.
If you drill the holes into a stud, go to step 3.
-OR-
If you drill the holes into an object other
than a stud, insert the wall anchors into
the holes. Tap gently on the ends with a
hammer until the wall anchors are flush with
the wall.
Insert the screws into the holes and
tighten the screws until only 1/4 inch of the
screws are exposed.
Align the wall mount holes on the baby unit
with the screws on the wall. Slide the baby
unit down until it locks into place.
Adjust the camera angle.
2
3
4
7
8
95
6
1
10
13
12
11
＜1 metre
＞1 metre
> 1 metre
> 1 metre
Parent unit main menu icons
Brightness
• You can change the brightness of
the parent unit screen.
LCD screen off timer
• You can set a specific time to
turn the screen off.
VOX sensitivity
• With this feature, you can
choose to hear sounds from the
baby unit all the time, or to hear
sounds that exceed a certain
level. You can use the parent
unit to adjust the microphone
sensitivity of your baby unit.
The higher the sensitivity level,
the more sensitive the baby
unit is in detecting sounds for
transmitting to the parent unit.
Sound-activated screen
• When the baby unit detects
no sound, the parent unit
screen stays off to save power.
Once a sound is detected, the
parent unit screen turns on
automatically. It will then turn
off again after 50 seconds of no
sound detection.
Temperature
• You can turn on the temperature
alert tone so that the parent
unit beeps whenever the room
temperature detected by the
baby unit falls outside of the
desired temperature range.
You can choose in Fahrenheit (oF)
or Celsius (oC) as the temperature
format displayed, or set the
maximum/minimum temperature
limit for alerts.
Parent unit warning icons and
messages
The selected baby unit is out
of range or is turned off.
The battery is empty and
needs to be recharged.
or
The temperature detected by
the baby unit is higher/lower
than the desired temperature
alert range.
The parent unit is searching
for baby units.
The parent unit is connected
to AC power.
Using the baby monitor
Power on or off the baby unit
• Slide the switch to to turn onON/OFF ON the
baby unit. The LED light turns on.POWER
• Slide the switch to to turn off ON/OFF OFF
the baby unit. The LED light turns off.POWER
Power on or off the parent unit
• Slide the switch to to turn on the ON/OFF ON
parent unit. The screen and the LED POWER
light turns on.
• Slide the switch to to turn off ON/OFF OFF
the parent unit. The screen and the POWER
LED light turns off.
Adjust parent unit speaker volume
• Press VOL /VOL on the parent unit to
adjust the speaker volume.
NOTE
• When the parent unit speaker volume is set to off,
appears on the screen.
Adjust LCD brightness
You can change the brightness of the parent
unit screen from to . The LCD Level 1 Level 5
brightness is preset to .Level 3
1. Press when the parent unit is idle.
2. Press or to choose , then press or
.
3. Press or to choose the desired level of
brightness, then press to conrm your
selection.
Screen off timer
You can set the screen off time for the parent
unit when there is no key press for a specic
time interval.
When the screen is turned off, you can still hear
sound from the baby unit.
1. Press when the parent unit is idle.
2. Press or to choose , then press or
.
3. Press or to choose the desired time
period to automatically turn off screen
( / - 5 min./ - 30 min. / - 60min.),
then press conrm your selection. to
Adjust the sound sensitivity of the
baby unit
You can choose to hear sounds from the baby
unit all the time, or to hear sounds that exceed a
certain level. You can use the parent unit to adjust
the microphone sensitivity of your baby unit. The
higher the sensitivity level, the more sensitive the
baby unit is in detecting sounds for transmitting to
the parent unit. The VOX sensitivity level is preset
to the highest level (Level 5).
Display Sensitivity Description
(Level 5) High
Sensitivity
Low
Sensitivity
Highest VOX
sensitivity level
The parent unit
speaker is constantly
on, and you will hear
all sounds (including
background noises)
from your baby’s room.
(Level 4) High VOX sensitivity
level
The parent unit
speaker turns on for
soft babbling and
louder sounds from
your baby. It remains
quiet when your baby
sleeps soundly.
(Level 3) Medium VOX
sensitivity level
The parent unit
speaker turns on for
loud babbling and
louder sounds from
your baby. It remains
quiet when your baby
makes soft sounds.
(Level 2) Low VOX sensitivity
level
The parent unit
speaker turns on for
crying and louder
sounds from your
baby. It remains quiet
when your baby
makes soft sounds.
(Level 1) Lowest VOX
sensitivity level
The parent unit
speaker turns on
for loud crying or
screeching sounds
from your baby. It
remains quiet when
your baby makes soft
sounds.
1. Press when the parent unit is idle.
2. Press or to choose , then press or
to open the submenu.
3. Press or to choose the desired sensitivity
level, then press to conrm your
selection.
NOTE
• If the screen is off, and the setting of sound-activated
screen is , then LCD screen will be turned on ON
automatically when VOX sensitivity is triggered.
Turn on or off the sound activation
When sound activation is on, as long as no sound
is detected within 50 seconds, the parent unit
screen will turn off automatically to save power.
When your baby unit detects a sound, which
exceeds the selected sensitivity level, the sound
activation triggers the parent unit screen to turn
on automatically. When no sound is detected
within 50 seconds, the screen will be off again.
1. Press when the parent unit is idle.
2. Press or to choose , then press or
to open the submenu.
3. Press or to choose or , then press
to conrm your selection.
NOTE
• If the sound sensitivity is set to the highest level,
the parent unit screen may remain on continuously
even though sound activation is on. This depends on
whether the baby unit detects any sounds
Zoom
You can zoom in while viewing images from the
baby unit.
• Press to zoom in.
• or to move the zoomed image Press
downward or upward.
• or to move the zoomed image Press
leftward or rightward.
• Press again to zoom out.
Talk
You can use the tion of the parent unit TALK func
to comfort your baby.
Press and hold on the parent unit. TALK
1. Speak towards the microphone on the parent
unit. Your voice is broadcast to the baby unit.
2. Release the TALK key to stop the broadcast.
Monitor the temperature
Your baby unit monitors the temperature of your
baby’s room with its built-in temperature sensor.
If the detected temperature is out of the preset
temperature range, the parent unit will display
an alert message.
Set temperature range
You can set the desired minimum and maximum
room temperature alert ranges.
1. Press when the parent unit is idle.
2. Press or to choose , then press .
3. Press or to choose , then press or
to open the submenu.
4. Press or to choose , then press or
.
5. Press or to choose the desired minimum
or maximum temperature, then press to
conrm your selection.
Temperature alert tone
You can turn on the temperature alert tone so
that the parent unit will emit an alert tone if the
detected temperature is out of range.
1. Press when the parent unit is idle.
2. Press or to choose , then press .
3. Press or to choose , then press or
to open the submenu.
4. Press or to choose or , then press
to conrm your selection.
Temperature format
You can choose to display the temperature in
Fahrenheit (o
F) or Celsius (oC).
1. Press when the parent unit is idle.
2. Press or to choose , then press .
3. Press or to choose , then press or
to open the submenu.
4. Press or to choose or , then press
to conrm your selection.
Night vision
The baby unit has infrared LEDs that allow you to
see your baby clearly at night or in a dark room.
When the baby unit being viewed detects low
light levels, the infrared LEDs are switched on
automatically. The images from the baby unit
are in black and white, and appears on the
screen.
NOTE
S
• It is normal if you see a short white glare on your
parent unit screen as the baby unit is adapting to
the dark environment.
• When the infrared LEDs are on, the images are in
black and white. This is normal.
TIP
• Depending on the surroundings and other
interfering factors, like lightings, objects, s and colour
backgrounds, the display resolution may vary. Adjust
the baby unit’s angle or place the baby unit at a
higher level to prevent glare and blurry display.
General product care
To keep this product working well and looking good,
follow these guidelines:
• Avoid putting it near heating appliances and
devices that generate electrical noise (for example,
motors or fluorescent lamps).
• DO NOT expose it to direct sunlight or moisture.
• Avoid dropping the product or treating it roughly.
• Clean with a soft cloth.
• DO NOT immerse the parent unit and the baby unit
in water and do not clean them under the tap.
• DO NOT use cleaning spray or liquid cleaners.
• Make sure the baby unit and parent unit are dry
before you connect them to the mains again.
Storage
When you are not going to use the baby monitor for
some time, store the parent unit, the baby unit and the
adapters in a cool and dry place.
Frequently asked questions
Below are the questions most frequently asked about the
soother. If you cannot nd the answer to your question,
please contact TecHelp on 1300 369 193.
Why does the
baby monitor
not respond
normally?
Try the following (in the order listed)
for common cure:
1. Disconnect the power to the
baby unit and the parent unit.
2. Wait a few seconds before
connecting power back to the
baby unit and the parent unit.
3. Turn on the baby unit and the
parent unit.
4. Wait for the parent unit to
synchronize with the baby unit.
Allow up to one minute for this to
take place.
Why don’t
the power-on
light of the
baby unit and
parent unit
go on when I
switch on the
units?
Perhaps the parent unit is not
connected to the power. Insert the
appliance plug into the parent unit
and put the adapter in a wall socket.
Then, slide the to switch ON/OFF
on the parent unit and to establish
connection with the baby unit.
Perhaps the baby unit is not
connected to the power. Insert the
appliance plug into the baby unit
and put the adapter in a wall socket.
Then, slide the switch to ON/OFF
ON to switch on the baby unit and
to establish connection with the
parent unit.
Why doesn’t
my parent
unit charge
while
connected to
AC power?
Make sure the power is not
controlled by a wall switch.
Why is my
screen in
black and
white?
The screen is in black and white
during night-time or in a dark room
when the night vision feature is
activated. This is normal.
Why do I get
glare or blurry
display on my
screen when
viewing my
baby at night?
During night-time or in a dark
room, the surroundings and other
interfering factors, like lightings,
objects, colours and backgrounds
may affect the image quality on
your parent unit screen. Adjust the
baby unit’s angle or place the baby
unit at a higher level to prevent
glare and blurry display.
Why does the
baby monitor
produce a
high-pitched
noise?
The parent unit and baby unit may
be too close to each other.
• Move the parent unit away from
the baby unit until the noise
stops; OR
• Turn down the volume of your
parent unit.
Why does the
parent unit
beep?
The baby unit may be out of range.
Move the parent unit closer to the
baby unit (but not less than 1 metre).
The parent unit may not have
enough charge for the parent unit
to perform normally. Charge the
battery in the parent unit for up to
11 hours.
The temperature of your baby’s
room may be too high or too low.
Why don’t I
hear a sound/
Why can’t I
hear my baby
cry?
The parent unit speaker volume may
be too low or off. Press
VOL to increase the volume, or
use the parent unit menu to change
sound sensitivity level to the highest
level (level 5).
Why can’t I
establish a
connection?
Why is the
connection
lost every
now and
then? Why are
there sound
interruptions?
The baby unit may be out of range.
Move the parent unit closer to the
baby unit (but not less than 1 metre).
Other electronic products may
cause interference with your baby
monitor. Try installing your baby
monitor as far away from these
electronic devices as possible.
Customer service and
product warranty
IMPORTANT
Please retain this booklet with your sales receipt as
proof of the date of purchase.
Customer Service
If you require assistance in operating this product,
please call the TecHelp Information Line on
1300 369 193 or contact VTech by e-mail at:
tcpsupport_au@vtech.com.
Voluntary Product Enquiry
In addition to your Statutory Rights and subject
to the conditions below, VTech warrants that this
product will be free from any defect in materials or
workmanship under conditions of normal use for a
period of 24 months from date of purchase.
VTech does not warrant that the product will be free
from defects if defects are caused by an accident,
misuse, abuse, improper installation or operation,
vermin infestations, lack of reasonable care,
unauthorised modication, loss of parts, tampering
or attempted repair by a person not authorised by
VTech; or where the product has been damaged by
lightning or a mains power surge.To make a claim
under this Voluntary Product Warranty you must call
the TecHelp Information Line on 1300 369 193 or
contact VTech by e-mail at: tcpsupport_au@vtech.
com where a Customer Service Representative will
inform you of the product return process. You will
need to ensure that:
• You provide proof of purchase;
• Your product is suitably packaged (original
packaging is not required); and
• You have included all components from the
original purchase.
For your records
Date of purchase:
Place of purchase:
Serial number:
For Voluntary Product Warranty purposes, proof of
purchase is required so please keep your receipt.
The benets conferred by this Voluntary Product
Warranty are in addition to other rights and remedies
that are available to you under law, which cannot be
excluded. The processes for this Voluntary Product
Warranty in no way limit your rights which arise as a
result of your Statutory Rights.
This Voluntary Product Warranty is given by:
VTech Telecommunications (Australia) Pty Ltd ABN 70
136 672 627
Address: 24 Gilby Road, Mount Waverley 3149
IMPORTANT NOTE: THIS IS NOT A PRODUCT
RETURN OR SERVICE ADDRESS – PLEASE CONTACT
TECHELP BY PHONE OR EMAIL FOR PRODUCT
AND WARRANTY SUPPORT. NO LIABILITY WILL BE
ACCEPTED BY VTECH FOR PRODUCTS RETURNED TO
THIS ADDRESS UNDER THIS VOLUNTARY PRODUCT
WARRANTY.
Phone number: 1300 369 193
Email address: tcpsupport_au@vtech.com
Statutory Rights
Our goods come with guarantees that cannot be
excluded under the Australian Consumer Law. You
are entitled to a replacement or refund for a major
failure and compensation for any other reasonably
foreseeable loss or damage. You are also entitled to
have the goods repaired or replaced if the goods fail
to be of acceptable quality and the failure does not
amount to a major failure.
Technical specications
Frequency
control
Crystal controlled PLL synthesizer
Transmit
frequency
Baby unit: 2402 - 2478.5 MHz Parent
unit: 2402 - 2478.5 MHz
Channels 52
LCD 2.4” Colour LCD
(QVGA 320x240 pixel)
Nominal
effective
range
Actual operating range may
vary according to environmental
conditions at the time of use.
Power
requirements
Parent unit: 3.6V Ni-MH battery
Baby unit power adapter: Output: 6V
DC @ 400mA
Parent unit power adapter: Output:
6V DC @ 400mA
Disposal of batteries and
product
The crossed-out wheelie bin symbols
on products and batteries, or on their
respective packaging, indicates they
must not be disposed of in domestic
waste as they contain substances that
can be damaging to the environment
and human health.
The chemical symbols Hg, Cd or
Pb, where marked, indicate that
the battery contains more than the
specied value of mercury (Hg),
cadmium (Cd) or lead (Pn) set out in
Battery Directive (2006/66/EC).
The solid bar indicates that the product
was placed on the market after 13th
August, 2005.
Help protect the environment by
disposing of your product or batteries
responsibly.
Specications are subject to change without notice.
Š 2020 VTech Telecommunications Ltd.
All rights reserved. 05/20. VM2700_AU_CIB_V3

Product specificaties

Merk: VTech
Categorie: Babyfoon
Model: BM2700

Heb je hulp nodig?

Als je hulp nodig hebt met VTech BM2700 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Babyfoon VTech

VTech

VTech RM5766HD Handleiding

27 Februari 2024
VTech

VTech Bel & Tel Handleiding

27 Juli 2023
VTech

VTech BM2150 Handleiding

18 Juli 2023
VTech

VTech BM5100-Bear Handleiding

11 Juni 2023
VTech

VTech BM5000 Handleiding

16 Mei 2023
VTech

VTech RM5762 Handleiding

23 December 2022
VTech

VTech Peppa Pig Handleiding

23 April 2023
VTech

VTech BM2700 Handleiding

12 April 2023
VTech

VTech Safe & Sound VM341 Handleiding

3 April 2023
VTech

VTech Sleepy Bear Handleiding

29 Maart 2023

Handleiding Babyfoon

Nieuwste handleidingen voor Babyfoon

Truelife

Truelife NannyTone VM Pocket Handleiding

16 April 2024
Beaba

Beaba Zen Premium Handleiding

5 April 2024
Philips

Philips Avent SCX361 Handleiding

2 April 2024
Philips

Philips AVENT SCD860 Handleiding

2 April 2024
Goclever

Goclever NANNY EYE Handleiding

21 Maart 2024
NUK

NUK Smart Control Multi 310 Handleiding

19 Maart 2024
NUK

NUK Eco Smart Control 300 Handleiding

19 Maart 2024
NUK

NUK Eco Control Handleiding

19 Maart 2024
Hubble Connected

Hubble Connected Nursery Pal Link Premium Handleiding

1 Maart 2024
Hubble Connected

Hubble Connected Guardian Pro Handleiding

1 Maart 2024