Venmar G2400HE Handleiding
Bekijk gratis de handleiding van Venmar G2400HE (56 pagina’s), behorend tot de categorie Airco. Deze gids werd als nuttig beoordeeld door 7 mensen en kreeg gemiddeld 4.5 sterren uit 4 reviews. Heb je een vraag over Venmar G2400HE of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/56
Venmar AVS
X24 ERV ECM
X24 HRV ECM
X30 ERV ECM
X30 HRV ECM
Venmar/vänee
X24 ERV ECM-N
X24 HRV ECM-N
X30 ERV ECM-N
X30 HRV ECM-N
vänee Gold SerieS
G2400E ECM
G2400H ECM
G3000E ECM
G3000H ECM
These products earned the ENERGY STAR
®
by
meeting strict energy efficiency guidelines set
by Natural Resources Canada and the US EPA.
They meet ENERGY STAR requirements only
when used in Canada.
22498 rev. J
READ AND SAVE THESE INSTRUCTIONS
VB0185
ABOUT THESE UNITS
1. New information about extended defrost setting, see page 15.
2. The only main wall controls compatible with these units are the X-Touch or Gold-Touch.
3. New balancing procedure, see page 16.
4. The terminal connectors for these units are already mounted to the electronic board.
USER AND INSTALLER MANUAL
Venmar Ventilation ULC, 550 Lemire Blvd., Drummondville, Québec, Canada J2C 7W9 venmar.ca 800-567-3855
2
Please take note that this manual uses the following symbols to emphasize particular information:
Identifies an instruction which, if not followed, might cause serious personal injuries including possibility of death.
CAUTION
Denotes an instruction which, if not followed, may severely damage the unit and/or its components.
NOTE: Indicates supplementary information needed to fully complete an instruction.
LIMITATION
For an installation and use in Canada only. Intended for a building on which Part 9 of division B from the effective version of the National
Building Code of Canada applies with additional restrictions and exception (see section 4 for more details). Installation work and electrical
wiring must be done by a qualified person in accordance with all applicable codes and standards, including fire-rated construction codes
and standards.
⚠WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSON(S) OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer.
2. Before servicing or cleaning this unit, disconnect the power cord from the electrical outlet.
3. This unit is not designed to provide combustion and/or dilution air for fuel-burning appliances.
4. When cutting or drilling into a wall or ceiling, do not damage electrical wiring and other hidden utilities.
5. Do not use this unit with any solid-state speed control device other than those specified in section 6.
6. This unit must be grounded. The power supply cord has a 3-prong grounding plug for your personal safety. It must be plugged into a
mating 3-prong grounding receptacle, grounded in accordance with the national electrical code and local codes and ordinances. Do
not remove the ground prong. Do not use an extension cord.
7. Do not install in a cooking area or connect directly to any appliances.
8. Do not use to exhaust hazardous or explosive materials and vapors.
9. When performing installation, servicing or cleaning this unit, it is recommended to wear safety glasses and gloves.
10. When applicable local regulation comprises more restrictive installation and/or certification requirements, the aforementioned
requirements prevail on those of this document and the installer agrees to conform to these at his own expense.
11. Due to the weight of the unit, two installers are recommended to perform installation
CAUTION
1. To avoid prematurely clogged filters, turn the unit OFF during construction or renovation.
2. Please read specification label on product for further information and requirements.
3. Be sure to duct air outside – Do not intake/exhaust air into spaces within walls or ceiling or into attics, crawl spaces, or garage.
Do not attempt to recover the exhaust air from a dryer or a range hood.
4. Do not run any air ducts directly above or within 2 ft (0.61 m) of a furnace or its supply plenum, boiler, or other heat-producing
appliances. If a duct has to be connected to the furnace return plenum, it must be connected 10’ (3.1 m) away from plenum’s
connection to the furnace.
5. The ductwork is intended to be installed in compliance with all applicable local and national codes.
6. When leaving the house for a long period of time (more than two weeks), a responsible person should regularly check if the unit
operates adequately.
7. If the ductwork passes through an unconditioned space (e.g.: attic), the unit must operate continuously except when performing
maintenance and/or repair. Also, the ambient temperature of the house should never drop below 18°C (65°F).
8. At least once a year, the unit mechanical and electronic parts should be inspected by qualified service personnel.
9. Do not use your unit during construction or renovation of your house or when sanding drywall. Certain types of dust and vapors may
damage your ventilation system.
10. During winter, make sure that the outside intake and exhaust hoods are free from any snow. During a big snow storm, check that your
unit doesn’t draw in any snow. If it does, turn the unit OFF for a few hours.
11. Since the electronic control system of the unit uses a microprocessor, it may not operate correctly because of external noise or very
short power failure. If this happens, unplug the unit and wait approximately 10 seconds. Then, plug the unit in again.
12. Do not make excessive use of fragrance appliances or chemicals since some may damage the unit components material.
⚠WARNING
Product specificaties
| Merk: | Venmar |
| Categorie: | Airco |
| Model: | G2400HE |
Heb je hulp nodig?
Als je hulp nodig hebt met Venmar G2400HE stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Airco Venmar
11 Juni 2025
7 April 2025
1 April 2025
1 April 2025
Handleiding Airco
- Bestron
- Tomado
- Truma
- Tosot
- Toshiba
- Daizuki
- Perfect Aire
- Candy
- Teco
- NewAir
- Remeha
- Meaco
- Korona
- HQ
- Avalon Bay
Nieuwste handleidingen voor Airco
30 Juli 2025
29 Juli 2025
29 Juli 2025
29 Juli 2025
29 Juli 2025
29 Juli 2025
29 Juli 2025
29 Juli 2025
29 Juli 2025
29 Juli 2025