VDO Dayton CR 2100 Handleiding

VDO Dayton Autoradio CR 2100

Lees hieronder de 📖 handleiding in het Nederlandse voor VDO Dayton CR 2100 (18 pagina's) in de categorie Autoradio. Deze handleiding was nuttig voor 24 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/18

* Depending on version

•Blue lead A5 (Electronic/Motor Aerial) :

This radio can provide a 12V signal for the

control of an automatic motor aerial or the

supply of an electronic aerial by connection.

Do not use this connection for the supply lead

of the aerial motor!

•Orange lead A6 (Pilot light) : Connect to

the dashboard illumination wiring of the car.

When the car headlights are switched on, the

backlight to the power key remains illuminated

(even when the radio is switched off). When

the set is on with this connection , the

brightness of the display is reduced.

CONNECTOR B (fig.2)

Loudspeakers (use 4 ohm loudspeakers

only)

• Do not connect any of the loudspeaker leads

to earth or directly to a booster/amplifier or via

an external fader!

• Connecting 4 loudspeakers

Front Rear

Left+ Green [B5] White [B7]

Left- Green/black [B6] White/black [B8]

Right+ Grey [B3] Blue [B1]

Right- Grey/black [B4] Blue/black [B2]

– To check the loudspeaker connections keep

the 'SCAN' key pressed and switch on the set.

To cancel switch off the set.

BLUE CONNECTOR C * for a Digital CD

changer (available separately) (fig. 3)

• You can only connect the following CD changer

with a digital output to this set :

- CH0400 or CH0600 or CH1000

Useful tips

Recommended connection instructions between

the CD changer and headunit :

1. Ensure that the Connector A (power supply) is

removed from the headunit.

2. Finish all connections between the CD changer

(see mounting instructions for the CD changer)

and the headunit.

3. Reconnect the Connector A (power supply) to

the headunit.

INSTALLATION

If your car is equipped with ISO connectors,

simply insert them in connectors of the car radio.

If not, you can use an adaptor cable (Refer to the

table on the separate installation card). Ensure all

cables are installed so that they cannot be

damaged by sharp edges or moving parts.

PREPARATION

Voltage and polarity: The set must be connected

to a 12V car battery with negative terminal to

earth (car chassis). Installation in vehicles not

fulfilling these requirements could result in

malfunction, damage or fire.

Warning: To prevent short-circuiting, disconnect

the negative car battery terminal until the set has

been mounted and connected (fig.1 See separate

installation card).

CONNECTOR A (fig.2)

POWER SUPPLY CONNECTIONS

•Red lead A7 : Connect to a permanent 12V

supply. This is the main power supply. Ensure

this connection can handle a current of 10A.

•Yellow/red lead A4 : Connect to a switched

12V supply (switched on/oﬀ by car ignition).

•Brown lead A8: Connect to earth (car

chassis).

This connection set up will enable you to make

full use of the ON/OFF LOGIC function of this set

limiting the use of the set to 1 hour after removal

of the ignition key. If this feature does not appear

to be functioning as expected you may require

an adapter cable (EA6259). See reverse of

installation card.

OPTIONAL CONNECTIONS (fig. 2)

•Pink lead A1 * (SDVC AND SPEED

WARNING) :

Speed Dependent Volume Control

automatically increases and decreases the

volume as a result of the car's speed.

Speed Warning can be used to inform you that

you are exceeding a certain speed.

•Connect pin A1 to a signal from the

speedometer of your car. Some cars are

already prepared for it (e.g. certain VW &

Vauxhall/Opel cars), please consult your dealer.

If not, you may need a more detailed

installation requiring extra equipment to

enable your car to become compatible.

This can only be accomplished by persons

familiar with automotive electrical and

mechanical systems. After connection see

‘SPECIAL FUNCTIONS’.

Complies with 21 CFR 1040.10

* Depending on version

OTHERS CONNECTIONS (fig.2)

Line-output *

• You can connect a power amplifier (with 2

additional loudspeaker) to this set with the RCA

cable.

– Connect Red socket to Right channel and white

socket to Left channel.

– Connect Blue wire to Amplifier Remote on/off.

Wired Remote Control

You can connect a wired remote control to this

set. Please note that you can also use an infrared

remote control* with this set.

TEMPERATURE SENSOR * (available

separately)

• You can connect a temperature sensor to this

set to automatically give a visible and audible

warning when the outside temperature

becomes lower than 3oC to warn of the

possibility of frost or black ice. The outside

temperature can also be shown by pressing

the 'DISPLAY' key.

– See the mounting instructions for the sensor.

– Connect the temperature sensor to the

connector marked (see separate installation

card).

– See INITIAL SETTINGS; select Option 'TEMP'

and set the Choice to 'C' (Celsius) or 'F'

(Fahrenheit).

This device is an aid only and cannot be

used to determine exact road conditions.

Use your own judgement at all times to decide

whether it is safe to continue driving.

Pink lead wire (Telephone mute)

• If your car telephone or the car kit of your mobile

phone provides a mute signal, it can be used to

automatically interrupt the set's sound output.

– Connect the telephone mute wire to Pink lead

wire (TEL. MUTE).

– See INITIAL SETTINGS; select

1 Option 'TEL' and set the Choice to 'MUTE'

2 Option 'PHONE' and set the Choice to 'LO' or

'HI' according to phone type.

TELEPHONE IN

• If your car telephone or the car kit of your mobile

phone provides both the mute signal and

loudspeaker connection, its output can be

amplified through the car's front speaker.

– Connect the telephone mute wire to Pink lead

wire (TEL. MUTE).

– Connect connector F (yellow) to the

loudspeaker output of your car phone or car

kit.

– See INITIAL SETTINGS; select

1 Option 'TEL' and set the Choice to 'IN'

2 Option 'PHONE' and set the Choice to 'LO' or

'HI' according to phone type.

Useful tips

Do not operate cellular phones near the set or

even in a car without using an outside antenna, it

may cause disturbances to all electrical systems

in the car.

REAR STUD

Screw rubber buffer E onto fixing stud at rear of

set.

AERIAL

Fix antenna adaptor * (EA6257/00) if needed.

• Insert aerial plug into aerial socket (good

reception is only possible with a good aerial).

* Depending on version

LEGEND

Briefly press the key.

Press and hold the key.

Press the key until you hear a

confirmation beep.

Turn the rotary knob.

Useful tips

ENVIRONMENT

This booklet is printed on low-chlorine

recyclable paper that can be used for

recycling.

CHECK BEFORE REQUESTING SERVICE

There may be times when you suspect that your

car radio is not functioning as you expected it to.

Before calling for service, please read the

operating / installation instructions and check for

useful tips under each section. You may find that

an apparent malfunction can easily be rectiﬁed.

If you still have to send your set for service, always

send the complete set (with detachable front). Do

not try to open the set to service it yourself.

MOUNTING

METAL SLEEVE (fig.4)

• Install the metal sleeve (dimension 182x53 mm) in the dashboard. For optimal performance of

the CD player*, the metal sleeve should be positioned horizontally (between -10

o and +30o).

• Fix metal sleeve into place by pressing the metal tags outwards using a screwdriver.

MOUNTING RADIO

This radio can be properly installed either from conventional Front Mounting or Rear Mounting.

FRONT MOUNTING

• Slide the radio into the metal sleeve until the springs at either side of the radio snap into the openings

of the sleeve (fig.5).

• Finally reconnect the negative car battery terminal (fig.6).

REMOVING RADIO (using the two U- brackets supplied)

• Remove the front, see 'SECURITY', 'DETACHABLE FRONT'.

• Insert both U-brackets into the holes on the front of the set until they lock. Pull out the radio (Fig.7).

REAR MOUNTING (fig.8)

• Remove the trimplate around the front panel and the side springs.

• Select a position where the screw holes of the mounting bracket and the screw holes of the radio

become aligned and tighten the screws at 2 places on each side.

• Only use M5 screws that are not longer than 6mm.

REPLACING FUSE (Fig. 2)

• Replace with a 10A blade-type fuse. The new fuse must be of exactly this value and type otherwise

the set will not be adequately protected. Ignoring this procedure may lead to damage to the set,

which will invalidate the guarantee.

INTERFERENCE SUPPRESSION

• Most modern cars have sufficient interference suppression. If you experience interference generated

by the car, consult your garage.

Product specificaties

Merk:	VDO Dayton
Categorie:	Autoradio
Model:	CR 2100
Kleur van het product:	Zwart
Afstandsbediening:	wird
Geïntegreerde geheugenkaartlezer:	Nee
Audiosysteem:	Dolby Digital
Gemiddeld vermogen:	76 W
Equalizer-instellingen:	Ja
Audio-uitgangskanalen:	4.0 kanalen
Diashow:	Nee
Ondersteunde frequentiebanden:	FM, LW, MW
Afmetingen (B x D x H):	180 x 150 x 50 mm
Inclusief RDS tuner:	Ja
CD-R afspelen:	Ja
CD-RW afspelen:	Ja
Te gebruiken met een iPod:	Nee
Maximaal vermogen per kanaal:	19 W
ISO-aansluiting:	Ja
Fader:	Ja