Vaddio RoboTRAK Handleiding
Pagina's 2 Engels Bewakingscamera
Bekijk de handleiding van Vaddio RoboTRAK gratis online of download de PDF. 17 mensen vonden deze handleiding nuttig. Vraag over dit model? Stel een vraag
© 2016 Vaddio - All Rights Reserved. Drop Down Mounts for RoboTRAK- Document Number 342-XXXX Rev A Page 1 of 2
Drop-Down Mount Accessory for RoboTRAK™
UNPACKING:
Carefully remove the product and all of the parts from the
packaging. Unpack and identify the following parts (cameras not
included):
➊
One (1) 1-14 Hex Nut (jamb nut)1.5” across by .375” Tall
➋
One (1) Offset Pipe with 1-14 Threads
➌
One (1) Mounting Flange (5” diameter)
➍
One (1) Tile Support Brace
➎
One (1) Large 5” Washer
➏
Two (2) 1-14 Hex Nut, 1.5” across x .547” Tall (one used as
fastener and the other as a top jamb nut)
(Cameras are not included)
Step 1: For suspended ceiling installations, mark a position in the center of
a ceiling tile where the ceiling mount is to be placed. The hole must be
positioned at the center of the ceiling tile lengthwise for 2’ x 4’ ceiling tiles to
line up with the tile support brace. Use the tile support brace as a template.
The tile support brace is meant to span the tile and distribute the weight into
the grid.
For drywall ceiling installations, mark a position in the ceiling while making
sure that there are no obstructions (structural supports, electrical, etc.) in the
area above the mount.
Step 2: Drill or cut a 1” (25.4mm) diameter hole in the tile or drywall at the
point where you marked the hole. For suspended ceiling installations, place
the support brace on the top of the ceiling tile and align the hole with the tile
support brace. There are six holes drilled in the support brace for attaching
to the building structure where regional codes require this additional support.
For drywall ceiling installations, place the Mounting Flange over the 1” hole,
and mark the four locations in the flange to install appropriate hardware (wall
anchors) for mounting the flange to the ceiling.
Step 3: Thread the 1.5” x .375” Jam Nut onto the bottom of the pipe (the side with the shorter threads), then thread the
Camera Platform all the way onto the pipe. Back the Camera Platform off the pipe (one rotation or less) until the back of the
Camera Platform aligns with the cable pass-thru. Carefully tighten the 1.5” x .375” Jam Nut down onto the threaded nut of the
Camera Platform.
Step 4: Thread the painted 5” flange onto the other end of the pipe.
Step 5: For suspended ceiling installations, slide the pipe with 5” flange end through the hole in the ceiling tile. From one tile
over, place the 5” washer onto the threaded pipe, and screw the first 1.5” x 5.5” hex nut onto the pipe thread and tighten the
hex nut down, then thread the second hex nut (jam nut) onto the top of the pipe and tighten it. Carefully feed the Cat-5 cabling
through the pipe and the cable pass-thru at the back of the camera mount. There are six (6) mounting points on the Tile
Support Brace to allow the integrator to tie the assembly to the structure for safety in seismic prone areas.
For drywall ceiling installations, once the appropriate mounting hardware for the flange is installed, carefully pull the Cat-5
cabling through the 1” hole in your drywall ceiling. Thread the cabling through the pipe, and pull it through the cable pass thru
at the back of the camera platform. Place the flange on the ceiling and tighten the screws down onto the mounting hardware.
Step 6: Place your camera onto the mount and secure it to the camera platform using the supplied black screw(s). Connect
the Cat. 5 cabling to the back of the camera and carefully feed excess Cat. 5 cabling back into the ceiling. Use the ¼” - 20
x .375: screws for the RoboSHOT cameras.
Installation and User Guide
➊
➏
➎
➍
➌
➋
Product specificaties
| Merk: | Vaddio |
| Categorie: | Bewakingscamera |
| Model: | RoboTRAK |
| Kleur van het product: | Zwart, zilver |
| Gewicht: | 1360 g |
| Breedte: | 155 mm |
| Diepte: | 145 mm |
| Hoogte: | 163 mm |
| Gebruiksaanwijzing: | Ja |
| Stroom: | 3 A |
| Ondersteuning voor plaatsing: | Muur |
| Connectiviteitstechnologie: | Bedraad |
| Ethernet LAN: | Ja |
| Type stroombron: | DC |
| Meegeleverde kabels: | AC, USB |
| Infrarood wavelength: | 850 nm |
| DC voltage input: | 12 V |
| Aansluiting voor netstroomadapter: | Ja |
| Beeldsensorformaat: | - " |
| Levensduur accu/batterij: | 40 uur |
| Ingebouwde camera: | Ja |
| Ethernet LAN, data-overdrachtsnelheden: | 10, 100 Mbit/s |
| Merkcompatibiliteit: | Vaddio |
| Temperatuur bij opslag: | -5 - 60 °C |
| Aansluiting: | RJ-45 |
| Web-gebaseerd management: | Ja |
| Luchtvochtigheid bij opslag: | 20 - 80 procent |
| Ophangsysteem voor aan de muur: | Ja |
| Aantal personen: | - persoon/personen |
| USB oplader inclusief: | Ja |
| Wand montagekit: | Ja |
| Bedrijfstemperatuur (T-T): | 0 - 24 °C |
| Relatieve vochtigheid in bedrijf (V-V): | 15 - 80 procent |
| Type product: | Volgsysteem |
| Code geharmoniseerd systeem (HS): | 85299097 |
| Aantal Power over Ethernet plus (PoE +)-poorten: | 1 |
| Kabel standaard: | Cat5e |
| Horizontale rotatie hoek: | -90 - 90 ° |
| Interface afstandsbediening: | IR Draadloos |
| Afmetingen camera (BxDxH): | 155 x 145 x 163 mm |
| Inclusief PoE-adapter: | Ja |
| Camera kabellengte (max): | 15.2 m |
| Conpensatiehoek: | 20 ° |
| Gewicht trackingmarkering: | 91 g |
| Afmetingen trackingmarkering: | 51 x 25 x 51 mm |
| Oplaadtijd trackingmarkering: | 4 uur |
| Inclusief trackingmarkering: | Ja |
| Type trackingmarkering: | Infrarood (IR) |
| Werkingsafstandbereik infraroodcamera: | 3.7 - 15.2 m |
| Aantal vooringestelde posities: | 10 |
Heb je hulp nodig?
Als je hulp nodig hebt met Vaddio RoboTRAK stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Bewakingscamera Vaddio
Vaddio Thin Profile Wall Mount Bracket Handleiding Vaddio RoboFLIP 30 HDBT Handleiding Vaddio EasyIP 20 Handleiding Vaddio EasyIP 30 Handleiding Vaddio EasyIP 5 ePTZ Handleiding Vaddio ZoomSHOT 20 SE AVBMP Handleiding Vaddio ConferenceSHOT ePTZ Handleiding
Alle Vaddio Bewakingscamera handleidingen
Handleiding Bewakingscamera
Nieuwste handleidingen voor Bewakingscamera
Hanwha Vision TNV-C8034RM Handleiding Hanwha Vision TID-600R Handleiding Hanwha Vision TNO-C4050T Handleiding Hanwha Vision QNP-6320HS Handleiding Kogan KASMSCPT12C Handleiding Hanwha Vision TNO-C4082T Handleiding Hanwha Vision XNV-A8084RS Handleiding Kogan KASMCMODSLA Handleiding Hanwha Vision TNO-6322ER Handleiding Hanwha Vision SLA-T4680DSA Handleiding