Ultimaker S5 Pro Bundle Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Ultimaker S5 Pro Bundle (41 pagina's) in de categorie Printer. Deze handleiding was nuttig voor 46 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/41
Ultimaker S5 Pro Bundle
Installation and user manual
EN 08/2020 v2.2 Original instructions
Ultimaker S5 Pro Bundle user manual 1
Table of contents
1. Safety and compliance
1.1 Safety messages 4
1.2 General safety information 4
1.3 Hazards 4
1.4 Health and safety 5
1.5 FCC / ISED regulatory notices 6
2. Introduction
2.1 Main components 8
2.2 Specications 11
3. Installation
3.1 Unboxing 13
3.2 What’s in the box 14
3.3 Hardware installation 15
3.4 Welcome setup 16
3.5 Firmware update 18
3.6 Install Ultimaker Cura 18
4. Operation
4.1 Touchscreen 20
4.2 Materials 20
4.3 Preparing a print with Ultimaker Cura 22
4.4 Remove the print 24
4.5 Remove support material 25
4.6 Change the printer conguration 26
4.7 Calibration 27
4.8 Uninstalling the Air Manager 29
4.9 Humidity control 29
5. Maintenance
5.1 Update the rmware 31
5.2 Material handling and storage 32
5.3 Maintenance schedule 32
5.4 Replace the Air Manager lter 33
6. Troubleshooting
6.1 Error messages 35
6.2 Print core troubleshooting 35
6.3 Print quality issues 35
6.4 Material Station troubleshooting 36
6.5 Air Manager troubleshooting 37
7. Warranty
7.1 General 39
7.2 Conditions 39
7.3 Notication 40
7.4 Exclusions 40
7.5 Applicable law and competent court 40
Ultimaker S5 Pro Bundle user manual 2
Disclaimer
Please carefully read and understand the contents of this installation and user manual. Failure to read the manual
may lead to personal injury, inferior results or damage to the Ultimaker S5 or its peripherals. Always make sure that
anyone who uses this 3D printer knows and understands the contents of the manual to make the most out of the
Ultimaker S5 Pro Bundle.
The Ultimaker S5, together with the Material Station and the Air Manager form the Ultimaker S5 Pro Bundle. This
user manual specically describes the intended workow and operation for the Ultimaker S5 Pro Bundle.
The conditions or methods used for assembling, handling, storage, use or disposal of the device are beyond our
control and may be beyond our knowledge. For this and other reasons, Ultimaker does not assume responsibility
and expressly disclaims liability for loss, injury, damage, or expense arising out of or in any way connected with the
assembly, handling, storage, use, or disposal of the product.
Intended use
The Ultimaker S5 Pro Bundle is a unique combination of the Ultimaker S5, Ultimaker S5 Air Manager, and the
Ultimaker S5 Material Station, which operate together.
Optimized software proles precisely control Air Manager ltering for every Ultimaker material and
compatible third-party laments. No worries about ultrane particles (UFPs), and no extra time is required
conguring your printer.
The Material Station and Air Manager empower the Ultimaker S5 to deliver high-quality 3D printed parts and
models at maximum output. The Ultimaker S5 Pro Bundle’s huge capacity and end-to-end material handling
increases print success rate, print quality, and uptime to 24/7 reliable production while minimizing human error,
print job time, and operator time.
The Ultimaker S5 Pro Bundle is built to deliver; it boosts condence to unlock more demanding applications with an
extended range of materials, while busy engineers and designers can focus all day doing their best work.
Product specificaties
| Merk: | Ultimaker |
| Categorie: | Printer |
| Model: | S5 Pro Bundle |
Heb je hulp nodig?
Als je hulp nodig hebt met Ultimaker S5 Pro Bundle stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Printer Ultimaker
31 Mei 2023
25 Mei 2023
22 April 2023
17 Januari 2023
11 Januari 2023
12 November 2022
Handleiding Printer
- Printer HP
- Printer Sony
- Printer Samsung
- Printer Xiaomi
- Printer Panasonic
- Printer Epson
- Printer LG
- Printer Huawei
- Printer Canon
- Printer Honeywell
- Printer Olympus
- Printer Toshiba
- Printer Xerox
- Printer Brother
- Printer Builder
- Printer Dell
- Printer Digitus
- Printer Dymo
- Printer Frama
- Printer Fujifilm
- Printer Fujitsu
- Printer Ibm
- Printer Intermec
- Printer Kodak
- Printer Konica Minolta
- Printer Kyocera
- Printer Lenovo
- Printer Lexmark
- Printer Minolta
- Printer Mitsubishi
- Printer MSI
- Printer Nec
- Printer Paxar
- Printer Polaroid
- Printer Primera
- Printer Renkforce
- Printer Ricoh
- Printer Roland
- Printer Royal Sovereign
- Printer Sagem
- Printer Seiko
- Printer Sharp
- Printer Star
- Printer Thomson
- Printer Tomy
- Printer Toshiba TEC
- Printer Triumph-Adler
- Printer Velleman
- Printer Zebra
- Printer Oce
- Printer Oki
- Printer Olivetti
- Printer Olympia
- Printer Argox
- Printer DTRONIC
- Printer Metapace
- Printer Citizen
- Printer Nilox
- Printer Approx
- Printer Bixolon
- Printer Brady
- Printer GoDEX
- Printer Testo
- Printer EC Line
- Printer Pantum
- Printer DNP
- Printer TSC
- Printer Equip
- Printer StarTech.com
- Printer Fichero
- Printer GG Image
- Printer Posiflex
- Printer ZKTeco
- Printer Star Micronics
- Printer Datamax-O'neil
- Printer Panduit
- Printer Dascom
- Printer HiTi
- Printer Vupoint Solutions
- Printer Elite Screens
- Printer Phoenix Contact
- Printer Colop
- Printer Raspberry Pi
- Printer Evolis
- Printer IDP
- Printer Fargo
- Printer Microboards
Nieuwste handleidingen voor Printer
26 April 2024
26 April 2024
26 April 2024
17 April 2024
17 April 2024
9 April 2024
9 April 2024
8 April 2024
8 April 2024
5 April 2024