Trust 56K PCI Modem Handleiding

Trust Router 56K PCI Modem

Lees hieronder de 📖 handleiding in het Nederlandse voor Trust 56K PCI Modem (8 pagina's) in de categorie Router. Deze handleiding was nuttig voor 22 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8

TRUST 56K PCI MODEM

U K

1. Introduction

This instruction manual is intended for the 'TRUST 56K PCI Modem’. This high-

speed, 56K PCI modem gives you a fast connection for Internet and e-mail use.

With the SuperVoice software, the Trust 56K PCI Modem is also ideal to use as a

handsfree telephone or a fax machine.

1.1 V92 standard

V92 is the future global standard devised by the ITU (International Telecom Union)

for communication between analogue modems. This improved standard is the

successor to the current V90 standard.

V92 is fully compatible with V90 and both standards have a download bandwidth of

56kbits/s. V92, however, has the following benefits:

• Improved data compression standard: V44 (V90 uses V42bis). This allows

for better data compression during data transfer, resulting in a higher

download speed. The increase in speed strongly depends of the nature of

the data being transferred: when downloading data that cannot be

compressed very easily, such as pictures in jpg format, the speed will equal

the speed achieved with V90.

• Increased upload speed (the maximum data transfer speed from your PC to

the Internet) to 48 kbit/s. V90 is limited to 33k6 bit/s.

• Faster 'connect time'. This is the time it takes to establish a full connection

with your ISP (Internet Service Provider). The technical name for this is V92

QuickConnect. This standard produces connect times of between 5 and 10

seconds.

• The 'modem standby' property. This property allows data communication to

be temporarily interrupted to accept incoming calls and to restart it after the

call has been ended.

At the time this manual was written, the V92 standard had not yet been issued. It is

expected to be ready in late October 2001, however, there may be some delay. As

soon as V92 becomes available, a firmware/driver update for the Trust 56K PCI

Modem will be placed on the Trust Internet site.

If you register your modem via www.trust.com/11709, you will be automatically

informed when the V92 firmware/driver is available.

Note: When the V92 standard is issued, it will probably take a few

months before your local ISP (Internet Service Provider) will

support the new standard. For further information, contact your

ISP.

TRUST 56K PCI MODEM

2 Safety

Carefully read the following instructions before use:

2.1 General information

1. Computer components may contain static electricity. You may receive an

electric shock if you touch the computer casing.

2. Turn the computer off and remove the plug from the plug socket before

opening the computer.

3. Make sure that the components you wish to add to your computer are

compatible with your system.

2.2 Modems

1. The modem is intended for connecting to a standard analogue telephone

line. Do not connect it to digital telephone systems, such as ISDN or ADSL.

This may cause damage and is dangerous.

2. During a thunderstorm, it is recommended to remove the telephone cable

from the telephone socket to prevent damage resulting from a lightning

strike.

3 Installation

3.1 Installing the hardware

Follow the steps below to install the Trust 56K PCI Modem:

1. Turn the computer off.

2. Remove the plug from the plug socket.

3. Remove the cover from the computer casing.

4. If fitted, remove the metal cover plate on the rear of a free PCI slot (white).

5. Insert the Trust 56K PCI Modem into the free PCI slot and screw it firmly

into place.

6. Place the cover back onto the computer.

7. Insert the plug into the plug socket.

8. Connect the telephone cable provided to the ‘LINE’ connection on the rear

of the modem.

9. Connect the other end of the telephone cable to your analogue telephone

socket.

You have now completed the installation of the hardware. Continue to the next

chapter for instructions on how to install the driver and the applications.

3.2 Installation in Windows 95, Windows 98, Windows ME,

Windows 2000 and Windows XP

1. Start Windows.

TRUST 56K PCI MODEM

U K

2. Windows will detect new hardware and ask for the location of the driver.

3. Insert the CD-ROM containing the driver and the applications into your CD-

ROM drive.

Note: The Trust Software Installer may start automatically when the

CD-ROM is inserted into your CD-ROM drive. You do not need

to use this and may close it.

4. Select the option to have Windows search in a specific location. Give one of

the paths below as the location:

- [D:\Win95] for installation in Windows 95

- [D:\Win98] for installation in Windows 98

- [D:\WinMe] for installation in Windows ME

- [D:\Win2000] for installation in Windows 2000

- [D:\WinXP] for installation in Windows XP

Note: The letter 'D' is used in the example above to indicate your CD-

ROM drive. Check which letter is used to indicate your CD-ROM

drive.

5. The driver will be found. Follow the instructions to install the program. Two

components will be installed:

- Trust 56K PCI Modem

- Wave Device for the Trust 56K PCI Modem (only in Windows 95, Windows

98 and Windows ME)

Note: During installation in Windows 2000 and Windows XP, you may

receive a message saying that the driver has not been signed.

This does not cause a problem for the functionality and you can

continue with the installation.

Note: If you register your 56K PCI modem via www.trust.com/11709,

you will be automatically informed when a signed driver is

available.

6. A modem Properties window will appear after the driver has been installed.

Select the ‘International Settings’ tab (see figure 1).

7. Select your country from the list and click on ‘Apply’ (see figure 1).

8. Click on ‘OK’ to close the window. You can display this window again at any

time via ‘Start – Settings – Control Panel’ and then double clicking on the

‘HaM Configuration’ icon.

9. Restart your system after the driver has been installed.

3.3 Installation in Windows NT4

The driver must be installed from the CD-ROM before the modem can be used.

1. Start Windows NT.

2. Log in as ‘Administrator’.

3. The ‘Trust Software Installer’ will start automatically. If it does not start

automatically, go to ‘Start – Run’ and type [D:\Setup.exe] in the command

line. Next, click on ‘OK’ (see figure 2).

4. Click on the ‘Windows NT4 Driver’ button to start the installation of the

driver (see figure 2).

5. Make sure the option to manually search for the driver is not selected and

click on ‘Next’. Windows NT4 will now automatically search for the driver.

6. The Trust 56K PCI Modem will be found. Click on ‘Next’.

Product specificaties

Merk:	Trust
Categorie:	Router
Model:	56K PCI Modem
Interface:	PCI
Plug and play:	Ja
Intern:	Ja
Compatibele besturingssystemen:	Win Windows 95, 98, ME, NT4, 2000
Mac-compatibiliteit:	Nee
Modemsnelheid:	56 Kbit/s
Minimale systeemeisen:	4x CD-ROM
Minimale processor:	Pentium 166 MHz
Minimale RAM:	16 MB
Modem (RJ-11) poort:	1