Tripp Lite SREXTENDER Handleiding

Tripp Lite Niet gecategoriseerd SREXTENDER

Bekijk gratis de handleiding van Tripp Lite SREXTENDER (20 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 37 mensen en kreeg gemiddeld 3.7 sterren uit 19 reviews. Heb je een vraag over Tripp Lite SREXTENDER of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Download PDF

Pagina 1/20

Owner’s Manual

SREXTENDER

Rack Enclosure Extension Frame

Important Safety Instructions

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that must be followed during the installation and operation of the product described in this

manual. Failure to comply may invalidate the warranty.

• Theinstructionsinthismanualareforcommonrackenclosuretypesandmaynotbeappropriateforallmountingapplications.Youmust

determine the ﬁtness of hardware and procedures before mounting. If hardware or procedures are not suitable for your application, contact the

manufacturer of your equipment for a solution.

• Rackmountequipmentmaybeextremelyheavy—becarefulwhenmovingorliftingequipment.Useoneormoreassistantsifnecessary.

Preparation

Note: Tripp Lite recommends using an assistant during installation. Descriptions of left and right are relative to the rear of your rack

enclosure. Illustrations may differ slightly from your enclosure, but procedures are similar for 48U, 42U and 25U enclosures unless

otherwise noted.

• Phillips-headScrewdriver(user-supplied;cordlessscrewdriverrecommended)

Tools Required

1111W.35thStreet,Chicago,IL60609USA

(773)869-1234•www.tripplite.com

Warranty

Registration:

chance to win a FREE Tripp Lite

product—www.tripplite.com/warranty

Español 8

Français 15

A B C D E H N

48/42U

1-1

Preparation (continued)

Note: The hinge swivels H and 12 hinge swivel screws L are pre-installed in the vertical sections A through D.

Parts List (If any parts are missing, contact Tripp Lite.)

ALowerLeftVerticalSection(1)

BLowerRightVerticalSection(1)

CUpperLeftVerticalSection(1)

DUpperRightVerticalSection(1)

ETopSection(1)

FBottomSection(1)

G1UBlankingPanels(3)

HHingeSwivels(6-allpre-installed)

IHinges(4)

JCableManagerBrackets(2)

KM6x12mmFlat-HeadScrews(8)

LM6x12mmPan-HeadScrews

andWashers(14total-12pre-installed)

MM5x10mmPan-HeadScrews

andWashers(40)

NGroundingCable(1)

OM5x20mmPan-HeadScrewsand

Washers(4)

PM4x8mmPan-HeadScrews

andWashers(8)

1 – Frame Assembly

Note: For 25U enclosures, you will use only the lower vertical sections A and B. You will not use the upper vertical sections C and D.

For 48U and 42U enclosures, you will use all four vertical sections.

(For25Uenclosures,skipthisstep.)Slidethelowerleftvertical

section A inside the upper left vertical section C as shown.

Repeatforthelowerrightverticalsection B and the upper right

vertical section D. The vertical sections are not interchangeable,

so refer to the diagram to conﬁrm that you’re assembling the

correct sections.

1-1

48U

42U

A AB B

C CD D

1-2

1-3

1-4

1-5

1 – Frame Assembly (continued)

(For25Uenclosures,skipthisstep.)Alignthesetoffourscrew

holes in the lower left vertical section A and the upper left

vertical section C.Usethelowersetofscrewholesfor48U

enclosures(thiswillmaketheverticalsectionlonger).Usethe

uppersetofscrewholesfor42Uenclosures(thiswillmakethe

verticalsectionshorter).InsertfourM5x10mmscrewsand

washers Mandtightensecurely.(Startallthescrewsbefore

tightening.)Repeatforthelowerrightverticalsection B and the

upper right vertical section D.

Insert the lower end of the left vertical section into the

bottom section Fasshown.Alignthescrewholes,insertfour

M5x10mmscrewsandwashers Mandtightensecurely.(Start

allthescrewsbeforetightening.)Repeatthisstepfortheright

vertical section.

Insert the upper end of the left and right vertical sections into the

top section E.Alignthescrewholes,inserteightM5x10mm

screws and washers Mandtightensecurely.(Startallthescrews

beforetightening.)

Insertthe1Ublankingpanels G into the top section E.

EachblankingpanelwillsnapintoplacewiththeTrippLitelogo

facingoutward.Theblankingpanelsmayberemovedtoinstall

standard19-inchrackaccessoriesupto3U–contactTrippLite

for more information.

1-2

1-3

1-4

1-5

Product specificaties

Merk:	Tripp Lite
Categorie:	Niet gecategoriseerd
Model:	SREXTENDER
Kleur van het product:	Zwart
Gewicht:	22680 g
Breedte:	601.7 mm
Diepte:	199.4 mm
Hoogte:	2216.2 mm
Gewicht verpakking:	22680 g
Breedte verpakking:	221 mm
Diepte verpakking:	1193.8 mm
Hoogte verpakking:	215.9 mm
Land van herkomst:	China
Aantal per verpakking:	1 stuk(s)
(Buitenste) hoofdverpakking hoogte:	215.9 mm
(Buitenste) hoofdverpakking breedte:	221 mm
(Buitenste) hoofdverpakking brutogewicht:	22680 g
(Buitenste) hoofdverpakking lengte:	1193.8 mm
Hoeveelheid per (buitenste) hoofdverpakking:	1 stuk(s)
Rackcapaciteit:	48U
Code geharmoniseerd systeem (HS):	7326.90.8688