Tripp Lite PDU3VSR6L1530 Handleiding

Tripp Lite Stekkerdoos PDU3VSR6L1530

Lees hieronder de 📖 handleiding in het Nederlandse voor Tripp Lite PDU3VSR6L1530 (72 pagina's) in de categorie Stekkerdoos. Deze handleiding was nuttig voor 16 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/72

Owner’s Manual

3-Phase Switched 0U Power

Distribution Units

(Phase, Bank and Outlet Measurements)

208V MODELS

PDU3VSR6L2120 • PDU3VSR6L2130 • PDU3VSR6H50

(Series Number: AG-00BC) (Series Number: AG-00BA) (Series Number: AG-00BA)

PDU3VSR6L1530 • PDU3VSR6G30

(Series Number: AG-00BA) (Series Number: AG-00BA)

400V MODELS

PDU3XVSR6G20

(Series Number: AG-00BD)

Important Safety Instructions 2

Installation 3

Digital Display 6

Using the Digital Display 8

Features 15

Conﬁguration and Operation 17

Service 17

Warranty and Warranty 18

Registration

Español 19

Français 37

Русский 55

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

14-04-275-9332F8.indb 1 4/30/2014 4:29:16 PM

Important Safety Instructions

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that should be followed during

the installation, operation, and storage of this product. Failure to heed these

instructions and warnings may affect the product warranty.

• The PDU provides convenient multiple outlets, but it DOES NOT provide surge or line noise

protection for connected equipment.

• The PDU is designed for indoor use only in a controlled environment away from excess

moisture, temperature extremes, conductive contaminants, dust or direct sunlight.

• Do not connect the PDU to an ungrounded outlet or to extension cords or adapters that

eliminate the connection to ground.

• The power requirement for each piece of equipment connected to the PDU must not exceed

the individual outlet’s load rating.

• The total power requirement for equipment connected to the PDU must not exceed the

maximum load rating for the PDU.

• Do not drill into or attempt to open any part of the PDU housing. There are no user-serviceable

parts inside.

• Do not attempt to modify the PDU, including the input plugs and power cables.

• Do not attempt to use the PDU if any part of it becomes damaged.

• Do not attempt to mount the PDU to an insecure or unstable surface.

• Use of this equipment in life support applications where failure of this equipment can

reasonably be expected to cause the failure of the life support equipment or to signicantly

affect its safety or effectiveness is not recommended. Do not use this equipment in the

presence of a ammable anesthetic mixture with air, oxygen or nitrous oxide.

• Never attempt to install electrical equipment during a thunderstorm.

• Keep indoor ambient temperature between 32°F and 122°F (0°C and 50°C).

• Connect the PDU to an outlet that is in accordance with your local building codes and that is

adequately protected against excess currents, short circuits and earth faults.

• The PDU must be installed by a qualied technician only.

• Install in accordance with National Electrical Codes. Be sure to use the proper over current

protection for the installation, in accordance with the plug rating/equipment rating.

• The electrical sockets supplying power to the equipment shall be installed near the equipment

and be easily accessible.

• Be sure to provide a local disconnect device on any models that are permanently installed

without a plug that is easily accessible.

14-04-275-9332F8.indb 2 4/30/2014 4:29:16 PM

1-1 1-2

1-4

1-3

1-5

Installation

Mounting the PDU

Note: The illustrations may differ somewhat from your PDU model. Regardless of conﬁguration, the user must

determine the ﬁtness of hardware and procedures before mounting. The PDU and included hardware are designed

for common rack and rack enclosure types and may not be appropriate for all applications. Exact mounting

conﬁgurations may vary. Screws for attaching the mounting brackets to the PDU are included. Use only the screws

supplied by the manufacturer or their exact equivalent.

Note: Mounting buttons come preinstalled to the PDU for toolless mounting.

1-1 To attach the mounting brackets to the

PDU, remove the mounting buttons.

1-2 Attach the mounting brackets to the

PDU with the included screws.

1-3 Attach the PDU to a vertical rail in

your rack or rack enclosure. (Use the

mounting hardware that came with your

rack or rack enclosure to attach the

mounting brackets to the rail.)

1-4 To reinstall the mounting buttons for

toolless mounting, remove the mounting

brackets then install the mounting

buttons onto the PDU. Position the PDU

as desired in the rack enclosure, align

the buttons with the rack mounting

slots, and slide the PDU into position.

Note: Be sure to insert the 2 buttons into either

the upper hole at of the PDU or into each end

the lower hole at of the PDU.each end

1-5 To install the PDU with its outlets facing

the rear of the rack, use the included

PDUMVROTATEBRKT accessory. First,

attach the mounting button A to the

V-shaped bracket B using the included

screw and washer. Then, use the

button-mount slot to attach the bracket

to the PDU and the mounting button to

attach the PDU to the rack. The bracket

effectively repositions the mounting

brackets allowing for the PDU outlets to

face the rear of the rack.

14-04-275-9332F8.indb 3 4/30/2014 4:29:18 PM

Product specificaties

Merk:	Tripp Lite
Categorie:	Stekkerdoos
Model:	PDU3VSR6L1530
Kleur van het product:	Zwart
Gewicht:	7510 g
Gewicht verpakking:	10570 g
Soort:	Driefasig
Gebruikershandleiding:	Ja
Materiaal behuizing:	Metaal
Afmetingen verpakking (BxDxH):	1927.1 x 245.1 x 175 mm
Certificering:	UL/CAN 60950-1, NOM, TAA
Duurzaamheidscertificaten:	RoHS
Temperatuur bij opslag:	-15 - 60 °C
Stroomspanning bescherming:	Overbelasting
Luchtvochtigheid bij opslag:	5 - 95 procent
Hoogte, in bedrijf:	0 - 10000 m
Afmetingen (B x D x H):	1778 x 55 x 73 mm
Montage:	Verticaal
Stekker:	NEMA L15-30P
Rackcapaciteit:	0U
AC-ingangsfrequentie:	50 - 60 Hz
Bedrijfstemperatuur (T-T):	0 - 50 °C
Aantal AC uitgangen:	30 AC-uitgang(en)
Nominale input voltage:	200-240 V
Stopcontacttypes:	C13 coupler, C19 coupler
Stroom (max.):	60 A
PDU types:	Geschakeld
Netspanning, in bedrijf:	200-240 V
Spanningsbeveiliging:	Ja
Aantal masterstopcontacten:	24
Aantal slavestopcontacten:	6
Maximale ingang stroom per fase:	20 A