TP Link EAP110-Outdoor V3 Handleiding

Bekijk gratis de handleiding van TP Link EAP110-Outdoor V3 (4 pagina’s), behorend tot de categorie Access point. Deze gids werd als nuttig beoordeeld door 57 mensen en kreeg gemiddeld 4.2 sterren uit 5 reviews. Heb je een vraag over TP Link EAP110-Outdoor V3 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Indoor/Outdoor Access Point

Overview

Package Contents

Panel Layout

© 2020 TP-Link 7106508837 REV3.3.0

Power LED:

On: Power on

Off: Power off

Note: EAP225-Outdoor does not support the Remote Reset feature.

Passive PoE Adapter

Remote Reset:

Press and hold for about 8 seconds until

the LED is quickly flashing yellow then

green. The EAP will restore to factory

default settings.

LED StatusIndication

Solid greenThe device is initializing or working properly.

Flashing yellowSystem errors. RAM, Flash, Ethernet, WLAN or

rmware may be malfunctioning.

Flashing yellow, greenFirmware update is in progress. Do not disconnect

or power o the device.

Quickly ashing yellow, green The device is being reset to its factory default

settings.

Flashes green twiceInitialization is completed.

SYS LED Explanation

Flashing green slowly

(Only for EAP225-Outdoor)The device is in an isolated state.

1

Lightning and ESD Protection

Before mounting the EAP, you should consider Lightning and ESD

Protection to ensure safety.

Proper grounding is extremely important for outdoor devices. By using a

shielded CAT5e (or above) cable for connection, you can reduce the

damage of ESD attacks.

Hardware Installation

Mount the EAP

The EAP can be pole-mounted or wall-mounted. Follow the steps below

for the appropriate installation.

Option 1: Pole Mounting

Lead the end of the pole mounting strap

through the back of the EAP.

Step 1:

Position the EAP and wrap the pole

mounting strap around the pole. Feed the

end through the screw-block and tighten

the strap until the EAP is secure.

Step 2:

Option 2: Wall Mounting

Step 1:

Place the mounting bracket (for EAP) in

the right position. Mark two positions

for the screw holes .

Drill two 6 mm holes for the screws at

the marked positions.

Step 2:

Insert the plastic wall anchors into the 6

mm holes. Align the bracket (for EAP) to

the plastic wall anchors and drive the

self-tapping screws into the anchors

through the bracket (for EAP).

Step 3:

Align the mounting tabs on the back of

the EAP with the slot of the mounting

bracket (for EAP). Push and slide the

EAP downward until it locks into place.

3Connect Cables

Firmly grasp the rear of the interface

cover and pull it downward.

Step 1:

Use an adequate Ethernet cable to

connect the LAN port. The length of

cable is up to 100 m for steady power

supply. Shielded CAT5e (or above) cable

is recommended.

Step 2:

Step 3:

Attach the waterproof rubber insert to the

groove at the underside of the device for

waterproong. Move the Ethernet cable to

the hole of the waterproof rubber insert.

Flatten the waterproof rubber insert until

it gets parallel to the device. Replace the

cover until it rmly locks into place.

Step 4:

EAP

Grounded PoE Adapter

Shielded CAT5e (or above)

Cable

Grounded 3-wire

Power Outlet

RESETShielded Ethernet

Port LAN

Passive PoE Adapter

(Mounting Bracket Included)

Power Cord

M3×28 Plastic Wall

Anchors (Qty.4)

M3×20 Self-tapping

Screws (Qty.2)

EAP

Antennas (Qty.2)

Mounting Bracket

(for EAP)

Installation Guide

Pole Mounting StrapWaterproof Rubber

Insert

M3×16 Self-tapping

Screws (Qty.2)

45

45

Connect the antennas to the EAP. For

optimal Wi-Fi performance, adjust the

direction of the antennas. It is recom-

mended to position the antennas at

45-degree angles.

Step 3:

45

45

Step 4:

Connect the antennas to the EAP. For

optimal Wi-Fi performance, adjust the

direction of the antennas. It is recom-

mended to position the antennas at

45-degree angles.

2

Quick Installation Guide

Setup with videos

Visit https://www.tp-link.com/support/setup-video/ or scan the QR

code to search for the setup video of your product model.

Product specificaties