Totolink EX200 Handleiding

Totolink Wifi-repeater EX200

Bekijk gratis de handleiding van Totolink EX200 (1 pagina’s), behorend tot de categorie Wifi-repeater. Deze gids werd als nuttig beoordeeld door 99 mensen en kreeg gemiddeld 3.5 sterren uit 50 reviews. Heb je een vraag over Totolink EX200 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Download PDF

Pagina 1/1

For more information, please go to www.totolink.net

Product Introduction

Method One: Quick Setup by Smart Phone

FAQ(Frequently Asked Questions)

Method Two: Wi-Fi Extension by WPS Button

Power on. Plug the device into any wall

socket that near the router. Wait until the

System LED blinks slowly.

1Press WPS button on Extender for about 2 seconds.

SSID: TOTOLINK_EX200

The Extend LED flash when

connecting and turns to solid

light when connected

Press WPS button on your router for about 2 seconds.

RST/WPS

Wi-Fi: Upper router’s SSID and password

The Extend LED turns to solid light, Wi-Fi extension successful. Please refer to to place the Extender.Relocate

EX200's default Network Name (SSID) is TOTOLINK_EX200 (no encryption).

With success repeater connection, this SSID (TOTOLINK_EX200) will change

to the same SSID (with same encryption) of upper Router/AP. After deployment,

just connect to the Router/AP's SSID. Congratulations, you have extended your

WiFi coverage successfully.

What should I do if I cannot access the extender’s web management

page?

A1: Make sure you have connected to the wireless network name of

the extender.

A2: Open any browser, enter 192.168.0.254 in the address bar and

press Enter.

A3: Reset the extender and connect to it again.

How to reset the extender to factory default settings?

Keep the extender power on, use a pin to press the RST button

on the bottom of device. When both System and Extend LED blinks,

release the button. The device will restore to factory default settings.

Quick Installation Guide

Wireless N Range Extender

Model No.: EX200

V1.0 | 1712

Information in this document is subject to change without prior notice.

On: The device is starting up or waiting for

extending.

Slow-blinking: The device is working normally.

Quick-flashing: The device is to restart.

Off: The device is power off.

On: Extending successfully.

-Good; -Normal; -Bad.Green Yellow Red

Slow-blinking: The device is extending to

upper Router/AP.

Quick-flashing: The device is to restart.

Off: No extending.

WPS: Press the button for about 2-3 seconds

to enable WPS.

LAN port: This port is used to connect to PC.

RST: Press the button for about 10 seconds, the

device will restore to factory default settings.

RST

Power on. Plug the device into any wall

socket that near the router. Wait until the

System LED blinks slowly.

1Connect to the Extender. Using your

smart phone to search Wi-Fi

TOTOLINK_EX200. (Settings—Wi-Fi)

2Login. The Setting page will turn up automatically.

Click . If below window doesn’tExtender Mode

appear, please open a browser and enter

192.168.0.254 manually.

3Extend Wi-Fi. Wait for a while, the Extender

auto-detects APs nearby. Choose your

router’s 2.4GHz SSID.

4 6 Verify. Check the LED status to verify

whether the Wi-Fi extension is

successful.

Configure . Enter its wireless password. Either keep

the default SSID or customize it for extended 2.4GHz

wireless network. Verify your settings and click Connect.

Relocate

Horizon Line

Host Network Extended Network

Vertically place the Extender

Wall Socket

Plug the extender into wall socket that halfway between your

router and the Wi-Fi dead zone. Wait about 30 seconds until

the Extend LED light turns solid green or yellow. If not, please

relocate it closer to your router to achieve better signal quality.

In order to make full use of extender, please keep the antennas

of the extender perpendicular to the horizontal plane. See blow:

Product specificaties

Merk:	Totolink
Categorie:	Wifi-repeater
Model:	EX200
Kleur van het product:	Wit
Soort:	Netwerkzender & -ontvanger
Materiaal behuizing:	Acrylonitrile butadiene styrene (ABS), Plastic, Polycarbonate (PC)
LED-indicatoren:	System, WLAN
Wi-Fi-standaarden:	802.11b, 802.11g, Wi-Fi 4 (802.11n)
Meegeleverde kabels:	LAN (RJ-45)
Snelstartgids:	Ja
Aantal Ethernet LAN (RJ-45)-poorten:	1
Plug and play:	Ja
Wifi-band:	Single-band (2.4 GHz)
Ethernet LAN, data-overdrachtsnelheden:	10, 100 Mbit/s
Bekabelingstechnologie:	10/100Base-T(X)
Netwerkstandaard:	IEEE 802.11b, IEEE 802.11g, IEEE 802.11n
Ondersteunde beveiligingsalgoritmen:	64-bit WEP, 128-bit WEP, WPA-PSK, WPA2-PSK
Soort antenne:	Extern
Antennas quantity:	2
Antenne versterkingsniveau (max):	4 dBi
Temperatuur bij opslag:	-40 - 70 °C
Draadloos LAN data-overdrachtsnelheid (max):	300 Mbit/s
Web-gebaseerd management:	Ja
Luchtvochtigheid bij opslag:	5 - 90 procent
Reset button:	Ja
Output current:	1 A
Spanning:	5 V
DHCP server:	Ja
Hostinterface:	RJ-45
DHCP client:	Ja
WPS Push Button Security:	Ja
Maximaal bereik:	30 m
Overdrachtssnelheid:	300 Mbit/s
Auto MDIX IEEE:	Ja
Wifi:	Ja
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	5 - 90 procent