Toa HY-BH10B Handleiding

Toa Niet gecategoriseerd HY-BH10B

Lees hieronder de 📖 handleiding in het Nederlandse voor Toa HY-BH10B (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 109 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1

Tip: The wall bracket supplied with each speaker is not used.

Step 1. h the r t to the r of the r Attac speake bracke rea speake

cabinet. Use the screws supplied with the speaker.

Note: Attach the s r t ac g to the peake bracke cordin

speaker mounting orientation.

Step 2. h a t br ket to e r br t us g e Attac join ac th hange acke in th

supplied 4 screws.

Step 3. Mount the speaker to the joint bracket.

Ins t the s ker ket to the t c t d er pea brac in join bra ke an

loo el secur ixin bol emporar speakes y e the f g t for t y r

installation.

Step 4. Attach the sliding bracket to the hanger bracket using the

knob bolt and plain washer. Select either mounting hole A

or B in the sliding bracket, depending on the thickness of

the partition board.

[Mountable partition board thickness]

Step 5. Mount the speaker to the partition board.

S e the s g c t to ch the tit n d lid lidin bra ke pin par io boar

betwee th slidin brac an hange brac et hen e g ket d r k , t n

tighten the knob bolt.

Step 6. Connect the speaker cable to the speaker input terminal.

For connections, refer to the instruction manual enclosed

with the speaker.

Step 7. Adjust the speaker's vertical mounting angle and tighten

the fixing bolt.

The speaker angle can be adjusted in 7.5º ps within ste

the range as follows.

F-1000 series: 0º (horizontal) to 45º downward

F-1300 series: 0º (horizontal) to 37.5º downward

When protection against falls is required:

Fix the sliding bracket directly to the

partition board using screws.

Not tha th fixin rew ar noe t e g sc s e t

supplied.

• re n or , be re to r y ad l e Befoinstallatio use su ca efull re al th

instructions in this section for correct and safe operation.

• Be sure to follow all the precautionary instructions in this section,

whi on ai impor an warning and au ion regardinch c t n t t s /or c t s g

safety.

• After reading, keep this manual handy for future reference.

1. SAFETY PRECAUTIONS

Indi ate potentiall haza dou situatio whichc s a y r s n , if

mishandled, could result in death or serious personal injury.

WARNING

• Install the unit only in a location that can structurally support the

weight of the unit and the speaker. Doing otherwise may result in

the s r f g n d g l i y /or peake allin dow an causin persona njur and

property damage.

• S ce the t is s d for r use, do t l it in uni de igne indoo no in alst

outdoo installe outdoo th agin pa cause thrs. If d rs, e g of rts s e

speaker to fall off, resulting in personal injury.

• Do t e r s n f d to t e t. no us othe method tha speci ie moun th uni

Extreme force is applied to the unit and the speaker could fall off,

possibly resulting in personal injuries.

• T ten h t y. E e t t the t s no se igheac bol securel nsur ha uni ha loo

join ins alla io pre en ac iden ha oul results a er ft t t n to v t c ts t t c d t in

personal injury.

• Use the specified speaker in combination. Doing otherwise may

cause the speaker to fall off, resulting in personal injury.

• Do not mount the unit in locations exposed to constant vibration.

Th uni ca damage ce ibration potentialle t n be d by ex ssive v , y

causing the speaker to fall, which could result in personal injury.

• Do not use anti-rust lubricant. If it contacts resin or rubber parts,

t y d t te d e the t to f , s y he coul de eriora an caus uni all pos ibl

resulting in personal injury.

Indi ate potentiall haza dou situatio whichc s a y r s n , if

mi handled coul re ul modera mino personas , d s t in te or r l

injury, and/or property damage.

CAUTION

• Avoid touching the unit's sharp metal edge to prevent injury.

• Do not hang down from the unit as this may cause it to fall down

or drop, resulting in personal injury and/or property damage.

INSTALLATION MANUAL

BOARD HANGER BRACKET HY-BH10B

The HY-B B B d r B et is used to t an H10 oar Hange rack moun

F / 0 S s r to a t y t d tit n -1000 130 erie speake emporaril ins alle par io

board.

Th pea in talle eithe ve ti hori ontae s ker can be s d in r a r cal or z l

orientation.

2. GENERAL DESCRIPTION

3. COMPONENT PARTS

4. FINISHED ASSEMBLING DIAGRAM

5. SPECIFICATIONS

Note

The design and specifications are subject to change without notice

for improvement.

6. INSTALLATION

37.5°

30°

0°

(horizontal)

Joint bracket

Speaker bracket

45°

30°

0°

(horizontal)

Refer to the figures below for the positional relationship

between the speaker bracket's "groove" and the joint

bracket's "indentation."

[F-1000 series]

[F-1300 series]

Note

The mating surfaces of the speaker bracket and joint

bracket are designed to interlock.

Ensure that both parts are securely engaged with each

other after mounting is complete.

Partition board

[Vertical installation] [Horizontal installation]

Joint bracket

(supplied with the speaker)

Fixing bolt

(supplied with the speaker)

Speaker bracket

(supplied with the speaker)

Accessory screw M5 x 10

Knob bolt

Plain washer for kob bolt

Hanger bracket

Sliding bracket

Mounting hole A

Mounting hole B

3, 7

Screw M5 x 20 (supplied with the speaker)

Speaker system

F-1000 series

T a he figure t ft le shows the

s t sit s crew moun ing po ion

for the F-1300 series.

Knob bolt x 1

Plain washer for knob bolt x 1

Hanger bracket x 1

Sliding bracket x 1

Machine screws

M5 x 10 with washers x 4

Mounting hole (A)

6 – 38 mm

Mounting hole (B)

28 – 60 mm

URL: http:// w.ww toa.jp/

133-01-00120-00

Applic le Speakerab

F-1000B, F-1000BT, F-1000W, F-1000WT,

F-1300B, F-1300BT, F-1300W, F-1300WT

Finish Steel plate, b ck, paint la

Dimensions 48 (w) x 100 (h) x 108 (d) mm

(knob bolt excl ed)ud

Weight 300 g

Product specificaties

Merk:	Toa
Categorie:	Niet gecategoriseerd
Model:	HY-BH10B
Kleur van het product:	Zwart
Gewicht:	210 g
Breedte:	48 mm
Diepte:	108 mm
Hoogte:	100 mm
Materiaal:	Staal
Compatibiliteit:	F-1000, F-1300