Thermocet VERSA LV-HV Handleiding
Lees hieronder de đź“– handleiding in het Nederlandse voor Thermocet VERSA LV-HV (14 pagina's) in de categorie Haarden. Deze handleiding was nuttig voor 23 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/14
Page.1
OPERATION AND INSTALLATION MANUAL
VERSA LV/HV
Page.2
CONTENTS
1. GENERAL Page 3
1.1 Delivery
1.2 Contents of packaging
1.3 First firing
1.4 Guarantee
2. OPERATING INSTRUCTIONS VERSA Page 3
2.1 Igniting
2.2 Operation of thermostat
2.3 Operation of glow-effect burner
2.4 Operation of fan
2.5 Switching off the fire
2.6 Maintenance
3. OUTLET SAFETY (T.T.B.) Page 4
4. ELECTRICAL INSTALLATION INSTRUCTIONS Page 5
5. GAS INSTALLATION INSTRUCTIONS Page 5
5.1 General instructions
5.2 Preparations for installing the fireplace
5.3 Installing the fireplace Page 6
6. DISMANTLING OF BURNER UNIT AND FAN Page 7
7. DISMANTLING OF T.T.B. BRACKET Page 7
8. LIST OF PARTS Page 7
9. GAS SPECIFICATIONS Page 8
DRAWINGS Pages 9/10
PHOTOGRAPHS LOG SET Page 11
Important tips Page 25
Guarantee certificate and registration card
Guarantee conditions Page 26
SUBJECT TO ALTERATIONS
NG 04240104 (2/22092003)
Page.3
We wish you happy heating with the purchase of this ThermoCet recessed gas fireplace. Please read
these instructions thoroughly before installing and using the fireplace. Keep these instructions care-
fully. Always state model and serial number in the event of a breakdown.
1. GENERAL
1.1 Delivery
You should inspect the appliance for damage in transit, immediately it has been delivered. If it is damaged,
you should report this without delay and as precisely as possible to your supplier. Please refer to the delivery
document.
1.2 Contents of packaging
1 x Completely assembled appliance
1 x Operation and installation manual
1 x Warranty card
1 x Pipe mouth with 4 self-tapping screws for connection of outlet
1.3 First firing
Your fireplace is coated with heat-resistant enamel that can withstand extremely high temperatures. Burn the
fire at high during the first hours of use and ventilate the room well. The curing of the enamel may produce a
smell/smoke, but this is harmless, however. Any marks on the glass can be removed immediately with glass
cleaner.
1.4 Guarantee ( see page 13 and 14)
Always complete your guarantee card in full and return it to your supplier immediately after purchase. Type
and serial number are shown on the plate that you will find on the bottom of the burner unit.
2. OPERATING INSTRUCTIONS VERSA
The Versa has a combined glow-effect and main burner (see page 10 figure 4). This burner can be operated
with either the thermostat knob (A) or the manual slide (B). You select the required setting with the thermo-
stat knob (A) and the modulating thermostat provides the right temperature. The hand-operated slide (B) al-
lows you to select the flame height you wish and the burner will continue to burn at that setting until you
change the selected setting.
2.1 Igniting.
* Open the gas stopcock fitted in the gas pipe to the appliance.
* Ensure that the thermostat knob (A) is at position n in the initial setting.
* Turn the thermostat knob (A) to the ignition position.Ă´
* Push the thermostat knob (A) and keep it pushed in.
* Push the ignition knob (C) all the way in until you hear a “click”; this is the spark ignition.
* You can see through the glass window whether the pilot light is burning. “Click” a few more
times if necessary, until the pilot light ignites.
* Keep the thermostat knob (A) pushed in for about another 30 seconds when the pilot light starts
burning and then release the knob.
* If the pilot light does not continue to burn, wait 5 minutes and then repeat the procedure.
* The burner is ignited by turning the thermostat knob (A) to the required setting (between set
tings 1 and 7, depending on the required temperature).
* To ignite the appliance with the glow-effect burner, move the slide (B) from position n depend-
ing on the required flame height (see figure). The glow-effect burner only functions when the
thermostat knob is between positions 1 and 7 (position 1 = low, position 7 = high).
Remark
Position (1) on the thermostat knob (A) is the pilot light setting if the room temperature is 10°C or more. If
the room temperature is below 10°C, the burner will also start to burn in position (1) until the temperature
has risen to 10°C.
Product specificaties
| Merk: | Thermocet |
| Categorie: | Haarden |
| Model: | VERSA LV-HV |
Heb je hulp nodig?
Als je hulp nodig hebt met Thermocet VERSA LV-HV stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Haarden Thermocet
12 Oktober 2023
12 Oktober 2023
12 Oktober 2023
12 Oktober 2023
12 Oktober 2023
12 Oktober 2023
12 Oktober 2023
12 Oktober 2023
12 Oktober 2023
12 Oktober 2023
Handleiding Haarden
- Haarden Quigg
- Haarden Altech
- Haarden Austroflamm
- Haarden Barbas
- Haarden Barbecook
- Haarden Bellfires
- Haarden Big Fire
- Haarden Blackline
- Haarden Blumfeldt
- Haarden Bocal
- Haarden Brula
- Haarden Brunner
- Haarden Dimplex
- Haarden Dovre
- Haarden DRU
- Haarden Edilkamin
- Haarden El Fuego
- Haarden Element4
- Haarden Faber
- Haarden Franco Belge
- Haarden Global Fires
- Haarden Godin
- Haarden Haas-Sohn
- Haarden Hergom
- Haarden Hwam
- Haarden Icon Fires
- Haarden Italiana Camini
- Haarden K-Stove
- Haarden Kago
- Haarden Kalfire
- Haarden Landmann
- Haarden Livin Flame
- Haarden M-design
- Haarden Manor House
- Haarden Mondena
- Haarden Napoleon
- Haarden Norsk Kleber
- Haarden Perel
- Haarden Qlima
- Haarden Ruby Fires
- Haarden Saey
- Haarden Spartherm
- Haarden Stuv
- Haarden Thermorossi
- Haarden Toolland
- Haarden Wanders
- Haarden Well Straler
- Haarden Xaralyn
- Haarden JAcobus
- Haarden Jydepejsen
- Haarden Olsberg
- Haarden OneConcept
Nieuwste handleidingen voor Haarden
4 December 2023
4 December 2023
4 December 2023
4 December 2023
4 December 2023
4 December 2023
4 December 2023
4 December 2023
17 Oktober 2023
17 Oktober 2023