Technoline WT 535 Handleiding

Technoline Radio WT 535

Lees hieronder de 📖 handleiding in het Nederlandse voor Technoline WT 535 (12 pagina's) in de categorie Radio. Deze handleiding was nuttig voor 39 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/12

Projector lens

RADIO CONTROLLED PROJECTION CLOCK WITH DIGITAL THERMOMETER

Instructions manual

INTRODUCTION:

Congratulations on purchasing this Projection clock with DCF-77 radio-controlled time. The operation of this

product is simple and straightforward and by reading this operating manual, users will receive the optimum

benefits of all its features.

FEATURES:

DCF-77 Radio controlled time with manual setting option

24 hours time display (hour, minutes, seconds)

Time projection (hour and minute)

Projection with adjustable brightness and projection orientation possible

Calendar display (weekday, date, month)

Alarm setting with snooze function

Time zone (±9 hours)

Indoor temperature display in degree Celsius

LED back-light

SETTING UP:

The Projection clock can be batteries operated or powered by the provided AC/DC adapter.

BATTERIES INSTALLATION

The Projection Clock uses 2 x AA, IEC LR6, 1.5V batteries. To install and replace the batteries, please follow

the steps below (the battery cover is located at the back of the unit):

1a) Press down at the arrow mark on top of the battery cover and pull to

open to reveal the battery compartment

b) Observing the correct polarity, insert the batteries (see markings inside

the battery compartment)

c) After inserting the batteries, replace the battery cover by clicking into

place

MODE/MIN key

AL/HR key Battery cover

Adjustable projector

SNOOZE key

Brightness key Direction key

Adapter socket

2a) Using a finger or other suitable object in the space at the

bottom center of the battery cover and pull to remove

b) Observing the correct polarity, insert the batteries (see

markings inside the battery compartment)

c) After inserting the batteries, replace the battery cover by

clicking into place

1. When the batteries are inserted, all the segments of the LCD will light up briefly and a “beep” will sound.

The Projection clock will now start receiving the DCF time signal. After approximate 3 to 5 minutes, the

DCF time and ‘DCF-77 Tower’ icon will be displayed.

2. If reception is not successful within approximately 10 minutes, either manually set the time or wait for the

clock to receive DCF time. Usually, the Projection clock will attempt to receive the DCF signal in the next

following hour. When this is successful, the received DCF time will override the manually set time. The

date is also updated with the received DCF time (Please refer also to notes on “Radio Controlled Time”

and “Manual Time Setting”).

Your Projection clock is now operational.

Note:

If the batteries are used as the main power source:

1. Projected image brightness, alarm volume and back-light strength would be weaker.

2. Battery life time would be much less than 1 year.

TO USE THE PROJECTOR POWER ADAPTER

The unit comes with an adapter unit for using the projector for an extended period of time, such as throughout

the night.

TO CONNECT THE ADAPTER:

Important!

Make sure that your household voltage is 230V! Otherwise it can result in damaging your

Projection clock.

1. Connect the power adapter to a wall socket.

2. Insert the adapter into the jack at the bottom of the clock.

3. The Projection clock will now start receiving the DCF time signal. After approximate 3 to 5 minutes, the

DCF time and ‘DCF-77 Tower’ icon will be displayed.

4. If reception is not successful within approximately 10 minutes, either manually set the time or wait for the

clock to receive DCF time. Usually, the Projection clock will attempt to receive the DCF signal in the next

following hour. When this is successful, the received DCF time will override the manually set time. The

date is also updated with the received DCF time (Please refer also to notes on “Radio Controlled Time”

and “Manual Time Setting”).

Your Projection clock is now operational.

Note:

If the Projection clock is powered through the adapter, the projection will be constantly ON at the highest

brightness level unless the brightness level is manually changed to a lower brightness level afterwards. And the

brightness of the projection can be change accordingly to enhance the clarity of the projected time by pressing

the key.

If the Projection clock is battery operated, the projection will be ON at the highest brightness level only when the

SNOOZE key is pressed. The intensity of the brightness level of the projection cannot be changed. If the

SNOOZE is released, the projection will be turned OFF.

Important!

If the DCF-77 signal is not being received, no keys functions can be used. In that case, either

wait for the next reception of the DCF signal or proceed to manual time setting after reset of the

clock for activation of the keys function.

BATTERIES POWERED WITH THE USE OF AC/DC ADAPTER

If the Projection clock is first powered by batteries and the power adapter is subsequently used for extended

period of time, the main power source of the Projection clock will switch to AC/DC power. The batteries will then

act as a backup power source in case of power failure.

TO RESET THE PROJECTION CLOCK

To reset the Projection clock to the factory default setting or in case of a malfunction, please remove all

batteries from the unit and unplug the AC/DC adapter from any power source. Wait at least for 3 minutes

before powering up the Projection clock again.

FUNCTION KEYS:

The radio-controlled Projection clock uses the following keys:

SNOOZE : Activate or deactivate snooze function

Alarm snooze function

: Activate the projection brightness at the highest level

: Exit the setting modes

: Back-light-On

AL/HR : Enter alarm setting mode

: Activate or deactivate alarm

: Stop alarm and snooze function

: Set the hours and day

: Back-light-On

MODE/MIN : Enter manual time setting mode

: Toggle between indoor temperature, seconds, alarm time, and date display

: Enter time zone setting mode

: Set the minutes, weekday and month

: Stop alarm and snooze function

: Back-light-On

: Set the brightness level of the projection (in A/C power mode)

(4 levels: High, Medium, Low, OFF)

: Back-light On

(BRIGHTNESS

key)

: Project the image direction (can display 4 different orientations)

: Back-light On

(DIRECTION

key)

Product specificaties

Merk:	Technoline
Categorie:	Radio
Model:	WT 535
Kleur van het product:	Zilver
Ingebouwd display:	Ja
Garantiekaart:	Ja
Alarm functie:	Ja
Agenda:	Ja
Snooze functie:	Ja
Gemiddeld vermogen:	- W
Backlight:	Ja
Thermometer:	Ja
MP3 afspelen:	Nee
Ophangsysteem voor aan de muur:	Ja
Ondersteunde frequentiebanden:	FM
Radio:	Klok
Afmetingen (B x D x H):	117 x 51 x 93 mm
Apple docking-compatibiliteit:	Niet ondersteund
Type batterij:	AA
Display met achtergrondverlichting:	Ja
Projectie functie:	Tijd
Projectie oppervlak:	Ceiling,Wall