Swann SWHOM-DC822P Handleiding

Swann Deurbel SWHOM-DC822P

Bekijk gratis de handleiding van Swann SWHOM-DC822P (4 pagina’s), behorend tot de categorie Deurbel. Deze gids werd als nuttig beoordeeld door 61 mensen en kreeg gemiddeld 3.7 sterren uit 31 reviews. Heb je een vraag over Swann SWHOM-DC822P of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Download PDF

Pagina 1/4

WIRELESS ALERT

Security Made Smarter

Wireless Door Chime

with Mains Power

EN INSTRUCTION MANUAL

PRODUCT OVERVIEW

INSTALLING THE DOORBELL

INSTALLING THE CHIME SPEAKER

1. Insert a small flat-head screwdriver into the small notch at the base of the Doorbell

and lift slightly to remove the rear cover.

2. Install the supplied "CR2032" battery with the "+" symbol facing up. Make sure the

battery is held down securely by the metal prongs.

Note: When replacing the rear cover, make sure the rubber weather seal is in place.

WARNING: The Doorbell unit contains a coin/button cell battery. If the coin/button cell battery is

swallowed, it can cause severe internal burns in just 2 hours and can lead to death. If the battery

compartment does not close securely, stop using the product and keep it away from children.

If you think the battery might have been swallowed or placed inside any part of the body, seek

immediate medical attention.

No wiring is necessary. Just plug the Chime Speaker into an easily accessible power point

and switch the power point on. The Chime Speaker, upon receiving power, automatically

goes into pairing mode for 10 seconds. Within this period, press the Doorbell button

to pair the Doorbell with the Chime Speaker. You will hear the default chime played as

confirmation.

If your Wireless Door Chime system comes with two Chime Speakers, simply repeat the

above procedures to install the additional Chime Speaker.

Note: To pair the Doorbell later, see " .Pairing the Doorbell"

1LED Indicator

2 (Pairing) Button

3VOL (Volume) Button

4 (Chime Select) Button

5Button

6Nameplate

Chime Speaker Doorbell

CHANGING THE CHIME

PAIRING THE DOORBELL

ADJUSTING THE CHIME SPEAKER VOLUME

MOUNTING THE DOORBELL

To change the chime that the Chime Speaker plays when someone presses the Doorbell

button, follow the steps below:

1. Press the button repeatedly on the Chime Speaker to cycle through the available

sounds.

2. Stop when you hear a sound that you would like played the next time someone

presses the Doorbell button.

3. Press the Doorbell button to test the chime.

To pair the Doorbell with the Chime Speaker, follow the steps below:

1. Press the button on the Chime Speaker.

2. Within 10 seconds, press the Doorbell button. The Chime Speaker sounds out the

chime that is currently selected as confirmation.

The Chime Speaker can support a maximum of 5 Doorbells at any one time. Additional

Doorbells are available for purchase separately.

The volume of the Chime Speaker is adjustable, if necessary, by pressing the button VOL

until the desired volume level is obtained.

The Doorbell can easily be mounted to the wall with the included double-sided adhesive

tape. The operating distance between the Chime Speaker and the Doorbell is up to

50m/165ft but the range may vary depending on local conditions.

Note: The Doorbell is not suitable for mounting on metal surfaces and UPVC doorframes

as these materials will interfere with the Doorbell's ability to communicate with the Chime

Speaker.

Product specificaties

Merk:	Swann
Categorie:	Deurbel
Model:	SWHOM-DC822P
Kleur van het product:	Wit
Montage gereedschap:	Ja
Type stroombron:	Batterij/Accu
Indicatielampje:	Ja
Ondersteund aantal accu's/batterijen:	1
Ingangsspanning:	100 - 240 V
Aantal:	1
Maximumbereik:	50 m
Frequentie:	433 MHz
Aantal inbegrepen batterijen:	1 stuk(s)
Batterijen inbegrepen:	Ja
Type batterij:	CR2032
Aantal belvolumeniveaus:	3
Regelbaar volume:	Ja
Verbindingstype:	Draadloos
Installatie instructie:	Ja