Supermicro MBD-X9SAE-V-O Handleiding
Supermicro
Moederbord
MBD-X9SAE-V-O
Bekijk gratis de handleiding van Supermicro MBD-X9SAE-V-O (105 pagina’s), behorend tot de categorie Moederbord. Deze gids werd als nuttig beoordeeld door 66 mensen en kreeg gemiddeld 4.7 sterren uit 33.5 reviews. Heb je een vraag over Supermicro MBD-X9SAE-V-O of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/105

X9SAE
X9SAE-V
USER’S MANUAL
Revision 1.0

Manual Revision 1.0
Release Date: July 11, 2012
Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document. Information in this document is subject to change without notice.
Other products and companies referred to herein are trademarks or registered trademarks of their
respective companies or mark holders.
Copyright © 2012 by Super Micro Computer, Inc. All rights reserved.
Printed in the United States of America
The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our web site at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and docu-
mentation, is the property of Supermicro and/or its licensors, and is supplied only under a license.
Any use or reproduction of this product is not allowed, except as expressly permitted by the terms
of said license.
IN NO EVENT WILL SUPER MICRO COMPUTER, INC. BE LIABLE FOR DIRECT, INDIRECT,
SPECIAL, INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE
USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPER MICRO COMPUTER, INC.
SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED
WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING,
INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Supermicro's total liability for all
claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class B
digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reason-
able protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
manufacturer’s instruction manual, may cause interference with radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turn-
ing the equipment off and on, you are encouraged to try to correct the interference by one or more
of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and the receiver.
•Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•Consult the dealer or an experienced radio/television technician for help.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warn-
ing applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”.
WARNING: Handling of lead solder materials used in this prod-
uct may expose you to lead, a chemical known to the State of
California to cause birth defects and other reproductive harm.

iii
Preface
Preface
This manu al is writ ten f or sy ste m inte grat ors, PC tec hnician s an d
knowledgeable PC users. It provides information for the installation and use of the
X9SAE Motherboard Series.
About This Motherboard
The X9SAE Motherboard Series supports a single Intel® Xeon® E3-1200
v2 series, Xeon E3-1200 series, Pentium®, and Celeron® processor in an LGA
1155 socket. With the Intel® C216 chipset built in, the X9SAE Motherboard Series
motherboard offers substantial enhancement in system performance for the entry-
level workstation or PC gaming platform.
Please refer to our website (http://www.supermicro.com/products/) for processor and
memory support updates. This product is intended to be installed and serviced by
professional technicians.
Manual Organization
Chapter 1describes the features,specications andperformance of themother-
board.
Chapter 2 provides hardware installation instructions. Read this chapter when in-
stalling the processor, memory modules and other hardware components into the
system. If you encounter any problems, see , which describes troubleChapter 3 -
shooting procedures for video, memory and system setup stored in the CMOS.
Chapter 4 includes an introduction to the BIOS, and provides detailed information
on running the CMOS Setup utility.
Appendix A provides BIOS Error Beep Codes.
Appendix B lists software program installation instructions.
Appendix C contains UEFI BIOS Recovery instructions.
Product specificaties
Merk: | Supermicro |
Categorie: | Moederbord |
Model: | MBD-X9SAE-V-O |
Breedte: | 304.8 mm |
Diepte: | 243.8 mm |
Ethernet LAN: | Ja |
Aantal USB 2.0-poorten: | 4 |
VGA (D-Sub)poort(en): | 1 |
Aantal Ethernet LAN (RJ-45)-poorten: | 2 |
Duurzaamheidscertificaten: | RoHS |
Meegeleverde software: | SuperDoctor III\r\nWatch Dog\r\nNMI |
Temperatuur bij opslag: | -40 - 70 °C |
Aantal poorten USB 3.2 Gen 1 (3.1 Gen 1) Type A: | 2 |
Processor socket: | LGA 1155 (Socket H2) |
PCI Express slots versie: | 2.0, 3.0 |
Processorfabrikant: | Intel |
Maximum intern geheugen: | 32 GB |
Luchtvochtigheid bij opslag: | 5 - 95 procent |
Audio-uitgangskanalen: | 7.1 kanalen |
PCI Express sleufhoeveelheid: | 6 |
ECC: | Ja |
Ethernet interface type: | Gigabit Ethernet |
Chipset moederbord: | Intel® C216 |
Trusted Platform Module (TPM): | Ja |
PCI Express x1 slots: | 2 |
Ondersteunde opslagstationinterfaces: | SATA II, SATA III |
Seriële poort(en): | 1 |
PCI Express x8 slots: | 2 |
PCI Express x4 slots: | 2 |
Geheugen voltage: | 1.5 V |
LAN controller: | Intel 82574L, Intel 82579LM |
Soorten RAID: | 0, 1,5, 10 |
Aantal SATA III connectors: | 2 |
Non-ECC: | Ja |
PCI-slots: | 1 |
Aantal ondersteunde processoren: | 1 |
Intel® Xeon series: | E3-1200 |
Maximum UDIMM geheugen: | 32 GB |
Aantal DIMM sloten: | 4 |
Ondersteunende RDIMM klok snelheden: | 1333,1600 MHz |
Ondersteunde geheugen types: | DDR3-SDRAM |
Wifi: | Nee |
Bedrijfstemperatuur (T-T): | 10 - 35 °C |
Relatieve vochtigheid in bedrijf (V-V): | 8 - 90 procent |
Moederbord form factor: | ATX |
Supported memory clock speeds: | 1333,1600 MHz |
BIOS type: | UEFI AMI |
Grootte BIOS-geheugen: | 16 Mbit |
ACPI version: | 4.0 |
Aansluiting voor ventilator van voeding: | Ja |
USB 2.0 aansluitingen: | 4 |
TPM connector: | Ja |
Aantal SATA II connectors: | 4 |
Serial port headers: | 1 |
Ondersteunende UDIMM module capaciteit: | 1GB, 2GB, 4GB, 8GB |
Heb je hulp nodig?
Als je hulp nodig hebt met Supermicro MBD-X9SAE-V-O stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Moederbord Supermicro
18 December 2024
4 December 2024
4 December 2024
4 December 2024
4 December 2024
4 December 2024
4 December 2024
4 December 2024
17 November 2024
17 November 2024
Handleiding Moederbord
- Sharkoon
- AOpen
- Intel
- Tyan
- Advantech
- Biostar
- MSI
- Foxconn
- Asrock
- Elitegroup
- Raspberry Pi
- EPoX
- Gigabyte
- NZXT
- ECS
Nieuwste handleidingen voor Moederbord
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
29 Juli 2025
29 Juli 2025
29 Juli 2025
29 Juli 2025