StarTech.com PEXUSB321C Handleiding

Bekijk gratis de handleiding van StarTech.com PEXUSB321C (2 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 10 mensen en kreeg gemiddeld 4.6 sterren uit 9 reviews. Heb je een vraag over StarTech.com PEXUSB321C of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Quick-Start Guide

To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.

Manual Revision: August 27, 2020

Product Diagram (PEXUSB321C)

Front Angle View

PortFunction

1USB-C Port

• Connect a USB Peripheral Device

• SuperSpeed USB 20Gbps

2Bracket

• Congurable for and Full Prole Low Height

installations

3PCIe p1-x4 Connector

• Connect the to the ® in USB CardPCI Express Slot

the Computer

Requirements

For the latest requirements, please visit:

www.startech.com/PEXUSB321C.

• Computer with an available PCI Express slot (x4, x8, or x16)

Tools

• Small Phillips Head Screwdriver

Hardware Installation

Warning: USB Cards can be damaged by static electricity. Make sure that the

InstallerComputer Case is properly grounded before they open the or touch the USB

Card. The should wear an when installing any computer InstallerAnti-Static Strap

component. If an is not available, discharge any built-up static Anti-Static Strap

electricity by touching a large for several seconds. Only Grounded Metal Surface

handle the by its edges and do not touch the gold connectors.USB Card

1-Port USB Card - SuperSpeed USB 20Gbps - 1x USB-C® - PCIe

Installing the Low Prole Bracket

By default the is attached to the . Depending on the Full Prole BracketUSB Card

system conguration it may be necessary to remove the and Full Prole Bracket

replace it with the (included).Low Prole Bracket

1. Using a , remove the two securing Small Phillips Head ScrewdriverBracket Screws

the to the .Full Prole BracketUSB Card

2. Align the on the with the on the Screw HolesUSB CardScrew HolesLow Prole

BracketUSB CardScrew HolesLow . Making sure the is sitting on-top of the on the

Prole Bracket.

3. Insert the through the and into the on the Bracket ScrewsUSB CardScrew Holes

Low Prole Bracket.

4. Using the , tighten the being Small Phillips Head ScrewdriverBracket Screws,

careful not to over-tighten.

Installing the USB Card

1. Turn o the and any that are connected ComputerPeripheral Devices

(e.g. printers, external hard drives, etc.).

2. Unplug the from the rear of the and disconnect any Power CableComputer

Peripheral Devices that are connected.

3. Remove the from the . CoverComputer Case

Note: Consult the documentation that came with the for details about Computer

how to do this safely.

4. Locate an open (x4, x8, or x16) and remove the corresponding PCI Express Slot

Metal Cover PlateComputer Case from the rear of the . In most instances, the

Metal Cover Plate Computer Case is attached to the rear of the with a single

ScrewScrew. Save this for the next step.

5. Gently insert the into the open and fasten the USB CardPCI Express SlotBracket

to the rear of the using the from step 4. Computer CaseScrew

6. Place the rear onto the . CoverComputer Case

7. Reconnect the to the rear of the .Power CableComputer

8. Reconnect all of the that were disconnected in step 2.Peripheral Devices

9. Connect a to the on the.USB Peripheral DeviceUSB-C Port USB Card

3

1

2

Product specificaties