StarTech.com 2P6GR-PCIE-SATA-CARD Handleiding

Bekijk gratis de handleiding van StarTech.com 2P6GR-PCIE-SATA-CARD (2 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 35 mensen en kreeg gemiddeld 4.2 sterren uit 9 reviews. Heb je een vraag over StarTech.com 2P6GR-PCIE-SATA-CARD of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Quick-Start Guide

To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.

Manual Revision: June 17, 2021

Product Diagram (2P6GR-PCIE-SATA-CARD)

Front View

PortFunction

1SATA Ports x 2

• Connect to the SATA Stoage DevicesSATA

Controller Card SATA Cable using a

2

RAID Conguration

Jumper (J1)

• ON - Allow RAID to be congured

• OFF - Lock RAID conguration

3LED Headers

• LED Header

Connect LED to monitor activity of a connected

SATA Storage Device

• ERR Header

Connect to monitor errors in the LEDRAID array

4PCIe p1-x2 Connector

• Connect the to the SATA Controller CardPCIe Slot

in the Computer

Product Information

For the latest product information, technical specications, manuals, and Declarations

of Conformance, please visit:

www.startech.com/2P6GR-PCIE-SATA-CARD.

Package Contents

• SATA Controller Card x 1

• Full-Prole Bracket (Installed) x 1

• Low-Prole Bracket x 1

• Quick-Start Guide x 1

2 Port SATA 6Gbps PCIe SATA Controller Card w/ RAID

Requirements

• Computer with an available PCIe slot (x4/8/16)

• Phillips Head Screwdriver

• SATA Cables

Hardware Installation

Warning: PCIe Cards can be damaged by static electricity. Make sure that the

InstallerComputer Case is properly grounded before they open the or touch the

SATA Controller Card. The should wear an when InstallerAnti-Static Strap

installing any computer component. If an is not available, discharge Anti-Static Strap

any built-up static electricity by touching a large for several Grounded Metal Surface

seconds. Only handle theby its edges and do not touch the SATA Controller Card

gold connectors.

Installing the Low-Prole Bracket

By default the is attached to the . Full-Prole BracketSATA Controller Card

Depending on the system conguration it may be necessary to remove the Full-

Prole BracketLow-Prole Bracket to replace with the (included).

1. Remove the 2x securing the , using a Phillips Head ScrewsFull-Prole Bracket

Phillips Head Screwdriver.

2. Remove the and replace with the Full-Prole Bracket Low-Prole Bracket

(included).

3. Install the 2x removed in step 1 and tighten, using a Phillips Head Screws Phillips

Head Screwdriver.

Installing the Card

1. Turn o the and any that are connected ComputerPeripheral Devices

(e.g. printers, external hard drives, etc.).

2. Unplug the from the rear of the and disconnect any Power CableComputer

Peripheral Devices that are connected.

3. Remove the from the . CoverComputer Case

Note: Consult the documentation that came with the for details about Computer

how to do this safely.

4. Locate an open (x4/8/16) and remove the corresponding PCIe SlotMetal Cover

PlateComputer CaseMetal Cover Plate from the rear of the . In most instances, the

is attached to the rear of the with a single . Computer CasePhillips HeadScrew

Save this for the next step. Phillips Head Screw

5. Gently insert the into the open (x4/8/16) and fasten SATA Controller Card PCIe Slot

the to the rear of the , using the BracketComputer CasePhillips HeadScrewfrom

step 4.

4

1

3

2

Product specificaties