SSV Works GN-F65 Handleiding
Bekijk gratis de handleiding van SSV Works GN-F65 (2 pagina’s), behorend tot de categorie Speaker. Deze gids werd als nuttig beoordeeld door 18 mensen en kreeg gemiddeld 4.6 sterren uit 9.5 reviews. Heb je een vraag over SSV Works GN-F65 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/2
GN-F65
Polaris General
6.5” Speaker Front Kick Panels
SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030
www.SSVworks.com | Phone: 818-991-1778 | Fax: 866-293-6751
!
Please read and understand these
instructions completely before
installation to avoid possible injury, or
damage to the accessory or vehicle.
WARRANTY INFORMATION:
All SSV Works enclosures are covered by a limited lifetime warranty against
defects in material or workmanship. All SSV Works Electronics are covered by a
limited 1 year warranty against defects in material or workmanship. All SSV Works
Speakers are covered by a limited 1 year warranty against defects in material or
workmanship. Labor for replacement of defective components is not covered.
Contact SSV Works for further warranty information.
TOOLS NEEDED FOR INSTALLATION
PARTS LIST IMAGES
CREASE LINE
CREASE LINE
PASSENGER SID E
CREASE LINE
CREASE LINE
DRIVER SIDE
2. M6 x 1.0 Screws x 6
1. GN-F65 Enclosures
(1 pair)
4. Drll Template
3. M6 Washers x 6
- T-30 Torx Driver - Drill with 1/4” Drill bit - Scribe or Punch tool
A. Cut out the INSIDE template (Driver/Passenger) along the cut
line. Position the template on kick panel above the foot rest
making sure to line up arrows on template to the curves of the
panel as seen on image A.
B. Using a scribing tool, mark the center of the 3 drill points
illustrated on the template as shown on image B.
A B
C. Using a ¼ drill bit, drill holes for mounting of kick Pods .
E. Use the provided M6 screws and washers and loosely tighten
the pod in place through the drilled holes. Once all screws
have been loosely installed, tighten down by hand.
F. Route the speaker wire away from any moving parts and any
sharp metal, then connect to the amplier.
Connecting the GN-F65 using the pre-installed, two-pin
connector will require an optional SSV Works plug-&-play
harness (WP-H1149 - sold separately). If you are not using the
WP-H1149 harness, simply cut off the two-pin connector and
follow the wiring instruction below.
C
E F
D. Place enclosure in location for mounting.
D
GN-F65 © 2017 SSV Works, Oxnard, CA 93030 GN-F65 Rev. A 10-5-17
WIRING INSTRUCTIONS
For proper sound, ensure the speaker polarity is correct
connect the “+” to the “+” and the “-“to the “-“from
the speaker wire to the amplier. If using with an SSV
Works complete system refer to the amplier wiring
instructions for more detailed wiring information.
“+”
“+”
“
-
”
“
-
”
Product specificaties
| Merk: | SSV Works |
| Categorie: | Speaker |
| Model: | GN-F65 |
Heb je hulp nodig?
Als je hulp nodig hebt met SSV Works GN-F65 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Speaker SSV Works
17 Augustus 2023
16 Augustus 2023
16 Augustus 2023
16 Augustus 2023
16 Augustus 2023
16 Augustus 2023
16 Augustus 2023
16 Augustus 2023
16 Augustus 2023
16 Augustus 2023
Handleiding Speaker
- Nyne
- Difrnce
- Audio Solutions
- Oppo
- Marshall Electronics
- Hama
- Harley Benton
- Tannoy
- TC Electronic
- AXESS
- ViewZ
- Autotek
- Dell
- The T.amp
- ERKEI SEHN
Nieuwste handleidingen voor Speaker
2 Augustus 2025
2 Augustus 2025
2 Augustus 2025
2 Augustus 2025
1 Augustus 2025
1 Augustus 2025
1 Augustus 2025
31 Juli 2025
31 Juli 2025
31 Juli 2025