Speco Technologies AP200M Handleiding

Speco Technologies Wifi-repeater AP200M

Lees hieronder de 📖 handleiding in het Nederlandse voor Speco Technologies AP200M (4 pagina's) in de categorie Wifi-repeater. Deze handleiding was nuttig voor 47 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
A
AP
P2
20
00
0M
M/
/A
AP
P3
30
00
0M
M 300Mbps, Outdoor Network Video Bridge w/DIP
function
Thank you for your choice of Speco Technologies’ point-to-point AP. These units are designed AP200M or AP300M
and manufactured to provide an efficient way to connect from two to five networking points directly and securely
at a distance of up to 7000’ line of site.
INCLUDED IN PACKAGE:
(1) AP dish
(1) Mount Assembly
(1) PoE Power Adapter
(1) AC Cord
(1) Package Mounting Hardware
OPERATING INSTRUCTIONS:
1) You will need two Cat5 cables for each dish to complete assembly
2) The PoE power adapter has 3 inputs. One is for the AC cord, and two are for networking. Please note the
PoE adapter and power cord are not designed for outdoor use and should be used indoors only.
a. The bottom of the adapter has two RJ45 connections. One marked POE and one marked LAN.
b. Using one Cat5 cable, connect one end to “LAN” and the
other end to your camera, recorder, PC, etc.
c. Use the other Cat5 cable to connect your AP dish to the
POE input.
3) Antennas should be mounted level with each other, and
transmission distance is greatly reduced if line of site is not clear
4) Antenna should always be mounted upright (RJ45 ports facing down) with port cover connected to ensure
maximum weather resistance.
5) Both RJ45 ports (black and yellow) on antenna are LAN connections.
6) DIP switch instructions:
Toggle 1 changes the mode of the dish. UP is access point (AP) mode for use with your recorder,
PC, etc.. DOWN is for use with your camera.
Toggles 2 through 6 are for matching AP dishes together. There are 32 various combinations
that can be made from the 5 keys, which corresponds to 32 different SSIDs and 32 different
segments. The chart below shows all possible combinations.
Toggles 7 & 8 are for point to multi-point functionality. To use up to 4 cameras with one
recorder, configure the DIP switches as follows:
1) On the recorder/PC/Switch side, switches 7 and 8 should remain up.
2) On the camera side, select one of 4 configurations for switches 7 and 8:
a. Camera 1: 7 Up and 8 Up
b. Camera 2: 7 Up and 8 Down
c. Camera 3: 7 Down and 8 Up
d. Camera 4: 7 Down and 8 Down
3) You cannot duplicate the switch settings between Cameras for switches 7 & 8 or you will
experience interference, thus the max of 4 points.
4) Each dish has a reception angle of 30 degrees horizontal and 60 degrees vertical.
SPECIFICATIONS:
Chipset Atheros AR9344 600MHz
DRAM DDR2 64MByte
FLASH
8MByte
IC
SiGe5004L
Port 10/100Mbps LAN*2
Speed
11a:54M,48M,36M,24M,18M,12M,9M,6Mbps
HT20:7.2M,14.4M,21.7M,28.9M,43.3M,57.8M,65M,72.2M,14.4M,
28.9M,43.3M,57.8M,86.7M,115.6M,130M,144.4Mbps
HT40:15M,30M,45M,60M,90M,120M,135M,150M,30M,60M,90M,120M,
180M,240M,270M,300Mbps
Transmission
DSSS, up to 7000’ line of sight with no interference
Dimensions 7.9” Diameter x 2.5” H (5.2” High with mount attached)
Modulation OFDM/BPSK/QPSK/CCK/DQPSK/DBPSK
Standard IEEE802.11n,IEEE802.11g,IEEE802.11b,IEEE802.3u,IEEE802.3af
Protocol CSMA/CA,TCP/IP,IPX/SPX,NetBEUI,DHCP,NDIS3,NDIS4,NDIS5
Channel AP200M: 2.372 ~ 2.532GHz AP300M: 4.96 6.065GHz ～
Power dissipation
≤6W
Power POE 24V 1A
RF
@25±2dB
802.11a
6-24Mbps
27±2dB
36-48Mbps 26±2dB
54Mbps
25±2dB
802.11n
HT20
MCS 0-3 27±2dB
MCS 4 26±2dB
MCS 5 25.5±2dB
MCS 6 25±2dB
MCS 7 24.5±2dB
HT40
MCS 0-3 26±2dB
MCS 4 25.5±2dB
MCS 5 25±2dB
MCS 6 24.5±2dB
MCS 7 24±2dB
Sensitivity
802.11a 6Mbps ≤ -89 54Mbps ≤ -73 ；
802.11n
HT20
MCS 0 ≤ -86; MCS 7 ≤ -68
HT40
MCS 0 ≤ -83; MCS 7 ≤ -65
Antenna
Frequency 4900 6100MHz ～
Direction Horizontal/Vertical
Gain
18DBi
Management
WEP management
Yes
SNMP MIB Yes
Telnet Yes
Serial Yes
Security
MAC address control
Yes
Encryption WEP 64/128bits,WPA,WPA2,802.1x
Operating conditions
Working temperature -22F~149F
Storage Temperature -58F~176F
Humidity (non-condensed) ≤95% NA（ ）

Product specificaties

Merk: Speco Technologies
Categorie: Wifi-repeater
Model: AP200M

Heb je hulp nodig?

Als je hulp nodig hebt met Speco Technologies AP200M stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Wifi-repeater Speco Technologies

Speco Technologies

Speco Technologies AP200M Handleiding

13 Mei 2023
Speco Technologies

Speco Technologies AP300M Handleiding

12 Mei 2023

Handleiding Wifi-repeater

Nieuwste handleidingen voor Wifi-repeater

Amped Wireless

Amped Wireless Artemis-AP APA1300M Handleiding

26 April 2024
Essentiel B

Essentiel B Easy WiFi 300P Handleiding

9 April 2024
Essentiel B

Essentiel B Easy WiFi AC 750 Handleiding

9 April 2024
Lindy

Lindy 43365 Handleiding

9 April 2024
TP Link

TP Link RE900XD Handleiding

27 Maart 2024
IDIS

IDIS DA-LP1101R Handleiding

24 Maart 2024
IDIS

IDIS DA-LP1101T Handleiding

24 Maart 2024
Hawking Technologies

Hawking Technologies Hi-Gain HW5AC Handleiding

21 Maart 2024
Hawking Technologies

Hawking Technologies Hi-Gain HWABN25 Handleiding

21 Maart 2024
TP Link

TP Link RE655 Handleiding

19 Maart 2024